journal article·2012-09

Microstructural and Residual Stress Development due to Inertia Friction Welding in Ti-6246

Moataz M. Attallah, Michael Preuss, Chatri Boonchareon, Axel Steuwer, John E. Daniels, Darren J. Hughes, Christopher Dungey, Gavin J. Baxter

Publisher page

Abstract

A thorough investigation has been performed to assess the microstructural properties, mechanical properties (hardness and elastic modulus), and residual stress development in Ti-6Al-2Sn-4Zr-6Mo (Ti-6246) inertia friction welds in the as-welded and postweld heat-treated conditions. It was evident that the thermomechanical deformation in the weld region occurred above the b transus, forming dynamically recrystallized b grains and precipitating acicular a within the b grains, which resulted in a localized hardness increase. In the heat-affected zone, a ghost microstructure of the base metal formed because of the absence of sufficient time for diffusion, resulting in Mo segregation in the prior primary a plates. Energy-dispersive synchrotron X-ray diffraction and neutron diffraction were used to assess the residual stress development in the three principal directions. The variation in the unstrained lattice parameters across the weld regions was established by imposing a stress balance on the axial stress component in the radial direction. It was found that the maximum stresses occurred in the hoop direction, with significantly lower stresses present in the radial and axial directions. The maximum tensile hoop stresses were located at ~4 mm from the weld centerline and not at the dynamically recrystallized b-rich weld zone. This was associated with the a fi b phase transformation and the subsequent acicular a precipitation within the region surrounding the weld centerline. © The Mineral, Metals & Materials Society and ASM International 2012.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. J. Esslinger and G. Lütjering: Proc. of the 10 th World Conference on Titanium (Ti-2003), J. Albrecht, ed., Wiley-VCH, Weinheim, Germany, 2003, pp. 2837-44.
2. G. Lütjering and J.C. Williams: Titanium, 2nd ed., Springer-Verlag, Berlin, Germany, 2007.
3. O.E. Kosing, R. Scharl, and H.J. Schmuhl: ASME Turbo Expo 2001, New Orleans, LA, 2001, pp. 1–6.
4. T.L. Oberle, C.D. Loyd, and M.R. Calton: SAE Trans., 1967,vol. 75, no. 660470, pp. 28–35.
5. C.G. Nessler, D.A. Rutz, R.D. Eng, and P.A. Vozzella: Weld. J., 50, 1971, pp. 79s–385s.
6. A. Barussaud and A. Prieur: Titanium ‘95—Science and technology; the 8th World Conference on Titanium, Birmingham, U.K., 1996, pp. 798–804.
7. C.L. English: Fabtech International ‘95, Society of Manufacturing Engineers, Chicago, IL, 1995, pp. 1237–50.
8. W.A. Baeslack III, D. Phillips, C. English, and A.P. Woodfield: J. Mater. Sci. Lett., 1991, vol. 10, pp. 1401–08.10.1007/BF00735692 ↗
9. O. Roder, D. Helm, and G. Lutjering: Tenth World Conference on Titanium, Wiley VCH, Hamburg, Germany, 1999, pp. 2875–82.
10. A. Barussaud and A. Prieur: 8 th World Conf. on Titanium (Titanium ‘95: Science and Technology), P.A. Blenkinsop, W.J. Evans, and H.M. Flower, eds., The Institute of Materials, Birmingham, U.K., 1995, pp. 798–804.
11. M. Preuss, P.J. Withers, and G.J. Baxter: Mater. Sci. Eng. A, 2006, vol. 437, pp. 38–45.10.1016/j.msea.2006.04.058 ↗
12. W.A. Baeslack III, D.W. Becker, and F.H. Froes: JOM, 36, 1984, pp. 46–58.10.1007/BF03338455 ↗
13. R.J. Moat, D.J. Hughes, A. Steuwer, N. Iqbal, M. Preuss, S.E. Bray, and M. Rawson: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 2098–2108.10.1007/s11661-009-9915-0 ↗
14. M.J. Donachie Jr.: Titanium: A Technical Guide, ASM International, Materials Park, OH, 1998.
15. C. Sauer and G. Luetjering: J. Mater. Process. Technol., 117, 2001, pp. 311–17.10.1016/S0924-0136(01)00788-9 ↗
16. M.M. Attallah, S. Zabeen, R.J. Cernik, and M. Preuss: Mater. Charact., 2009, vol. 60, pp. 1248–56.10.1016/j.matchar.2009.05.006 ↗
17. CSM+ Indentation Software User’s Guide, Peseux, Switzerland, 2008.
18. A. Steuwer, J. Santisteban, M. Turski, P.J. Withers, and T. Buslaps: J. Appl. Crystallogr., 2004, vol. 37, pp. 883–89.10.1107/S0021889804023349 ↗
19. A.C. Larson and R.B. Von Dreele: General Structure Analysis Software (GSAS). Los Alamos National Laboratory Report No. LAUR 86-748, Los Alamos National Laboratory, Los Alamos, NM, 2000, http://www.ncnr.nist.gov/xtal/software/gsas.html.
20. M.R. Daymond, M.A.M. Bourke, and R.B. Von-Dreele: J. Appl. Phys., 1999, vol. 85, pp. 739–47.10.1063/1.369154 ↗
21. P.J. Withers, M. Preuss, A. Steuwer, and J.W.L. Pang: J. Appl. Crystallogr., 2007, vol. 40, pp. 891–904.10.1107/S0021889807030269 ↗
22. M. Preuss, J.W.L. Pang, P.J. Withers, and G.J. Baxter: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 3227–34.10.1007/s11661-002-0308-x ↗
23. M. Attallah, S. Bray, and M. Preuss: The 8 th Int. Conf. on Trends in Welding Research, Pine Mountain, GA, 2008.
24. Y. Ito, Y. Moriguchi, and T. Nishimura: Tetsu-To-Hagané, 1986, vol. 72, pp. 625–32.10.2355/tetsutohagane1955.72.6_625 ↗
25. I. Sen and U. Ramamurty: Scripta Mater., 2010, vol. 62, pp. 37–40.10.1016/j.scriptamat.2009.09.022 ↗
26. M.M. Attallah, M. Preuss, and S. Bray: The 8 th Int. Conf. on Trends in Welding Research, ASM International, Pine Mountain, GA, 2008.
27. Y.T. Lee and G. Welsch: Mater. Sci. Eng. A, 1990, vol. 128, pp. 77–89.10.1016/0921-5093(90)90097-M ↗
28. Z. Fan: Scripta Metall. Mater., 1993, vol. 29, pp. 1427–32.10.1016/0956-716X(93)90331-L ↗
29. J. Romero, M.M. Attallah, M. Preuss, M. Karadge, and S.E. Bray: Acta Mater., 2009, vol. 57, pp. 5582–92.10.1016/j.actamat.2009.07.055 ↗
30. M. Karadge, M. Preuss, C. Lovell, P.J. Withers, and S. Bray: Mater. Sci. Eng. A, 2007, vol. 49, pp. 182–91.10.1016/j.msea.2006.12.095 ↗
31. G. Lütjering: Mater. Sci. Eng. A, 1998, vol. 243, pp. 32–45.10.1016/S0921-5093(97)00778-8 ↗
32. A.R. Denton and N.W. Ashcroft: Phys. Rev. A, 1991, vol. 43, pp. 3161–71.10.1103/PhysRevA.43.3161 ↗
33. M. Preuss, P.J. Withers, and G.J. Baxter: Mater. Sci. Eng. A, 2006, vol. 437, pp. 38–45.10.1016/j.msea.2006.04.058 ↗
34. S. Bein and J. Bechet: J. Phys., 1996, vol. 6, pp. 99–108.
35. J.W.L. Pang, M. Preuss, P.J. Withers, G.J. Baxter, and C. Small: Mater. Sci. Eng. A, 2003, vol. 356, pp. 405–13.10.1016/S0921-5093(03)00153-9 ↗