journal article·2013-06Open access

An Investigation on the Fatigue Fracture of P/M Al-SiC Nanocomposites

H. Ghasemi Yazdabadi, A. Ekrami, H. S. Kim, A. Simchi

Abstract

A tensile-compression fatigue response of Al matrix composites containing different amount of SiC nanoparticles (50 nm diameter) up to 6 vol. pct was studied. The nanocomposite powders were prepared by a powder metallurgy (P/M) route consisting of mechanical alloying, hot extrusion, and hot closed-die forging. The microstructure of the materials was evaluated by optical microscopy, scanning and transmission electron microscopies, and electron backscattered diffraction. A fine distribution of the nanoparticles in submicron and ultrafine grains was obtained. The low cycle fatigue behavior was examined in stress control mode under fully reversed tension-compression cycle at 1 Hz up to 1000 cycles. High cycle fatigue was conducted using a push-pull test up to 107 cycles with the minimum to maximum stress ratio of 0.1 at a frequency of 40 Hz. Cyclic hardening was observed at a low cycle fatigue regime with an enhanced hardening rate in the presence of SiC nanocomposite. The fatigue endurance limit at 107 cycles was also improved by nanoparticles. Fractographic studies revealed a mixture of ductile-brittle fracture modes with an increase in the ductile fracture mode at higher SiC fractions. The fatigue fracture mechanism was found to be local ductile deformation, microscopic void formation, and coalescence.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. M.A. Meyers, A. Mishra, and D.J. Benson, Prog. Mater Sci., 2006, vol. 51, pp. 427–56.10.1016/j.pmatsci.2005.08.003 ↗
2. V. Viswanathan, T. Laha, K. Balani, A. Agarwal, and S. Seal, Mater. Sci. Eng. R, 2006, vol. 54, pp. 121–285.10.1016/j.mser.2006.11.002 ↗
3. C. Borgonovo and D. Apelian, Mater. Sci. Forum, 2011, vol. 678, pp. 1–22.10.4028/www.scientific.net/MSF.678.1 ↗
4. S.K. Thakur, K.S. Tun, and M. Gupta, J. Eng. Mater. Technol., 2010, vol. 132, pp. 041002–06.10.1115/1.4002150 ↗
5. L. Kollo, M. Leparoux, C.R. Bradbury, C. Jäggi, E. Carreno-Morelli, and M. Rodríguez-Arbaizar, J. Alloys Compd., 2010, vol. 489, pp. 394–400.10.1016/j.jallcom.2009.09.128 ↗
6. E.Y. Gutmamas, Prog. Mater Sci., 1990, vol. 34, pp. 261–366.10.1016/0079-6425(90)90003-R ↗
7. H. Asgharzadeh, A. Simchi, and H.S. Kim, Mater. Sci. Eng. A, 2011, vol. 528, pp. 3981–89.10.1016/j.msea.2011.01.082 ↗
8. H. Asgharzadeh, A. Simchi, and H.S. Kim, Mater. Sci. Eng. A, 2012, vol. 542, pp. 56–63.10.1016/j.msea.2012.02.031 ↗
9. Z.R. Hesabi, H.R. Hafizpour, and A. Simchi, Mater. Sci. Eng. A, 2007, vol. 455, pp. 89–98.10.1016/j.msea.2006.11.129 ↗
10. A.H. Monazzah, A. Simchi, and S.M.S. Reihani, Mater. Sci. Eng. A, 2010, vol. 527, pp. 2567–71.10.1016/j.msea.2010.01.060 ↗
11. R.W. Hertzberg: Deformation and Fracture Mechanics of Engineering Materials, Wiley, New York, 1996.
12. H. Simchi and A. Simchi, Mater. Sci. Eng. A, 2009, vol. 507, pp. 200–06.10.1016/j.msea.2009.01.037 ↗
13. H. Mughrabi, Procedia Eng., 2010, vol. 2, pp. 3-26.10.1016/j.proeng.2010.03.003 ↗
14. T. Hanlon, Y.-N. Kwon, and S. Suresh, Scripta Mater., 2003, vol. 49, pp. 675–80.10.1016/S1359-6462(03)00393-2 ↗
15. H.W. Höppel, M. Kautz, C. Xu, M. Murashkin, T.G. Langdon, R.Z. Valiev, and H. Mughrabi, Int. J. Fatigue, 2006, vol. 28, pp. 1001–10.10.1016/j.ijfatigue.2005.08.014 ↗
16. H. Mughrabi and H.W. Höppel, Int. J. Fatigue, 2010, vol. 32, pp. 1413–27.10.1016/j.ijfatigue.2009.10.007 ↗
17. H. Höppel, H. Mughrabi, M. Zhouy, and R.Z. Valiev, Philos. Mag. A, 2002, vol. 82, pp. 1781–95.10.1080/01418610208235689 ↗
18. L.B. Kong, T.S. Zhang, J. Ma, and F. Boey, Prog. Mater Sci., 2008, vol. 53, pp. 207–322.10.1016/j.pmatsci.2007.05.001 ↗
19. C. Suryanarayana, Prog. Mater Sci., 2001, vol. 46, pp. 1–184.10.1016/S0079-6425(99)00010-9 ↗
20. H. Asgharzadeh, A. Simchi, and H.S. Kim, Mater. Sci. Eng. A, 2010, vol. 527, pp. 4897–4905.10.1016/j.msea.2010.04.031 ↗
21. X.Z.L. F. Zhou, Y.T. Zhu, S. Dallek, and E.J. Lavernia, Acta Mater., 2003, vol. 51, pp. 2777–91.10.1016/S1359-6454(03)00083-1 ↗
22. R.B. Calhoun and D.C. Dunand: in Comprehensive Composite Materials, Pergamon, Oxford, 2000.
23. C. Tekmen, I. Ozdemir, U. Cocen, and K. Onel, Mater. Sci. Eng. A, 2003, vol. 360, pp. 365–71.10.1016/S0921-5093(03)00461-1 ↗
24. N. Hansen, Scripta Mater., 2004, vol. 51, pp. 801–06.10.1016/j.scriptamat.2004.06.002 ↗
25. J.R. Bowen, P.B. Prangnell, D. Juul Jensen, and N. Hansen, Mater. Sci. Eng. A, 2004, vols. 387–389, pp. 235–39.10.1016/j.msea.2004.01.127 ↗
26. Z. Zhang and D.L. Chen, Scripta Mater., 2006, vol. 54, pp. 1321–26.10.1016/j.scriptamat.2005.12.017 ↗
27. C. Tjong, Adv. Eng. Mater., 2007, vol. 9, pp. 639–52.10.1002/adem.200700106 ↗
28. Z. Zhang and D.L. Chen, Mater. Sci. Eng. A, 2008, vol. 484, pp. 148–52.10.1016/j.msea.2006.10.184 ↗
29. W.D. Callister Jr., Materials Science and Engineering: An Introduction, 6th ed., Wiley, New York, 2003.
30. W.Z. Han, A. Vinogradov, and C.R. Hutchinson, Acta Materialia 2011, vol. 59, pp. 3720–36.10.1016/j.actamat.2011.03.007 ↗
31. J. LLorca, Prog. Mater. Sci., 2002, vol. 47, pp. 283–353.10.1016/S0079-6425(00)00006-2 ↗
32. J. Schijve, Int. J. Fatigue, 2005, vol. 27, pp. 1031–39.10.1016/j.ijfatigue.2005.03.001 ↗
33. H.D. Solomon, Low Cycle Fatigue: A Symposium, ASTM International, New York, 1988.10.1520/STP942-EB ↗
34. P. Cavaliere, Int. J. Fatigue, 2009, vol. 31, pp. 1476–89.10.1016/j.ijfatigue.2009.05.004 ↗
35. Z.Z. Chen and K. Tokaji, Mater. Lett., 2004, vol. 58, pp. 2314–21.10.1016/j.matlet.2004.02.034 ↗