journal article·2004-08

Second-order stresses and strains in heterogeneous steels: Self-consistent modeling and X-ray diffraction analysis

K. Inal, J. L. Lebrun, M. Belassel

Publisher page

Abstract

Theoretical and experimetal methods have been developed to characterize the effect of mechanical loading on the mesoscopic and macroscopic mechanical state of polycrystalline materials. Ferritic and austenitic single-phase materials were first analyzed, then phase interaction was studied in a multiductile phase material (austeno-ferritic duplex steel) and a natural reinforced composite (pearlitic steel). The theoretical method is based on the self-consistent approach in which elastic and plastic characteristics of the phases have been applied through the micromechanical behavior of single-crystal-using slip systems and microscopic hardening. The effects of a crystallographic texture and phase interaction during loading and after unloading were studied. The elastic and plastic anisotropy of the grains having the same crystallographic orientation were assessed by diffraction strain analysis. The simulation was compared with the experiments performed using the X-ray diffraction technique. In the considered duplex and pearlitic steels, it was observed that the ferrite stress state is much lower than the austenite and cementite ones. The results of diffraction strain distribution have showed the pertinence of the models and give valuable information, for example, for the yield stress and the hardening parameters of each phase in a two-phase material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Composite Material Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (80)

Show source-provided references
1. G.B. Greenough: Proc. R. Soc. London A, 1949, vol. 197, pp. 182–86.
2. G. Maeder: Chem. Scripta, 1986, vol. 26A, p. 23.
3. E. Macherauch, H. Wohlfahrt, and U. Wolfstieg: High Temp. Mater. Proc., 1973, vol. 28, p. 201.
4. V. Hauk, R.V.M. Oudelhoven, and G.J.H. Vaessen: Metall. Trans. A, 1982, vol. 13A, pp. 1239–44.10.1007/BF02645507 ↗
5. I.C. Noyan and J.B. Cohen: Mater. Sci. Eng., 1986, vol. 79, p. 149.10.1016/0025-5416(86)90398-8 ↗
6. R.A. Winholtz and J.B. Cohen: Metall. Trans. A, 1992, vol. 23A, pp. 341–54.10.1007/BF02660876 ↗
7. P. Hadmar, P. Mabelly, L. Barrallier, and J.M. Sprauel: J. Phys. IV, 1996, vol. 6, p. 219.
8. G.A. Webster and R.C. Wimpory: J. Mater. Processing Technol., 2001, vol. 117, pp. 395–99.10.1016/S0924-0136(01)00802-0 ↗
9. Y.Y. Qiu: J. Alloys Compounds, 1996, vol. 234, pp. 157–66.10.1016/0925-8388(95)02082-9 ↗
10. A.J. Wilkinson: Proc. ICRS 6, Oxford, United Kingdom, July 10–12, 2000, IOM Communications, London, UK, 2000, vol. 1, p. 625.
11. J. Brechbühl, J. Bauch, and H.J. Ullrich: Cryst. Res. Technol., 1999, vol. 34, pp. 59–70.10.1002/(SICI)1521-4079(199901)34:1<59::AID-CRAT59>3.0.CO;2-# ↗
12. A. Wanner and D.C. Dunand: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 2949–62.10.1007/BF02830344 ↗
13. U. Lienert, H.F. Poulsen, R.V. Martins, and A. Kvick: Mater. Sci. Forum, 2000, vols. 347–349, pp. 95–100.10.4028/www.scientific.net/MSF.347-349.95 ↗
14. S. Taira and K. Hayashi: Proc. 13th Jpn. Congr. on Materials Research, ISMS Publications, Kyrtr, 1970, p. 20.
15. H. Dölle, V. Hauk, H. Kockelmann, and H. Sesemann: J. Strain Anal., 1977, vol. 12 (1), p. 62.10.1243/03093247V121062 ↗
16. H. Dölle and J.B. Cohen: Metall. Trans. A, 1980, vol. 11A, pp. 831–36.10.1007/BF02661212 ↗
17. C.M. Brakman: Cryst. Res. Technol, 1985, vol. 20 (5), p. 593.10.1002/crat.2170200503 ↗
18. M. Barral M, J.L. Lebrun, J.M. Sprauel, and G. Maeder: Metall. Trans. A, 1987, vol. 18A, pp. 1229–38.10.1007/BF02647192 ↗
19. K. Inal, P. Gergaud, M. François, and J.L. Lebrun: Scand. J. Metall., 1999, vol. 28, pp. 139–50.
20. V. Hauk: Structural and Residual Stress Analysis by Nondestructive Methods, Elsevier, New York, NY, 1997.
21. V. Van Acker, P. Van Houtte, and E. Aernoudt: Proc. ICRS4, Baltimore, June 8–10, 1994, SEM, Bethel, USA, pp. 402–09.
22. A. Baczmanski, K. Wierzbanowski, and J. Tarasiuk: Z. Metallkd., 1995, vol. 86 (7), pp. 507–11.
23. K. Inal and M. François: Proc. ECRS4, Cluny, France, 1996.
24. B. Bacroix, G. Canova, and H. Mecking: Large Plastic Deformation, Balkema Publishers, Rotterdam, 1993, p. 101.
25. D. Raabe: Mater. Sci. Eng., 1995, vol. A197, pp. 31–37.10.1016/0921-5093(94)09770-4 ↗
26. R.A. Lebensohn and G.R. Canova: Acta Mater., 1997, vol. 45 (9), pp. 3687–94.10.1016/S1359-6454(97)00067-0 ↗
27. P. Van Houtte, L. Delannay, and S.R. Kalidindi: Int. J Plast., 2002, vol. 18, pp. 359–77.10.1016/S0749-6419(00)00102-9 ↗
28. T.H. Lin: J. Mech. Phys. Solids, 1957, vol. 5, p. 143.10.1016/0022-5096(57)90058-3 ↗
29. M. Berveiller and A. Zaoui: J. Mech. Phys. Solids, 1979, vol. 6, p. 326.
30. T. Iwakuma and S. Nemat-Nasser: Proc. R. Soc. London, 1984, vol. A394, pp. 87–119.
31. D.J. Eshelby: Proc. R. Soc. London, 1986, vol. A407, p. 343.
32. G.I. Taylor: J. Inst. Met., 1938, vol. 62, p. 307.
33. R. Hill: J. Mech. Phys. Solids, 1965, vol. 13, pp. 89–161.10.1016/0022-5096(65)90023-2 ↗
34. D.J. Eshelby: Proc. R. Soc. London, A241 1957, vol. A241, pp. 376–96.
35. E. Kröner: Acta Metall., 1961, vol. 9, pp. 155–61.10.1016/0001-6160(61)90060-8 ↗
36. P.R. Morris: Int. J. Eng. Sci., 1970, vol. 8, pp. 49–61.10.1016/0020-7225(70)90014-5 ↗
37. P. Lipinski and M. Berveiller: Int. J. Plast., 1989, vol. 5, pp. 149–72.10.1016/0749-6419(89)90027-2 ↗
38. R. Masson, M. Bornert, P. Suquet, and A. Zaoui: J. Mech. Phys. Solids, 2000, vol. 48, pp. 1203–27.10.1016/S0022-5096(99)00071-X ↗
39. A. Paquin, S. Berbenni, V. Favier, X. Lemoine, and M. Berveiller: Int. J. Plast., 2001, vol. 17, pp. 1267–1302.10.1016/S0749-6419(00)00047-4 ↗
40. T. Mori and K. Tanaka: Acta Metall., 1973, vol. 21, p. 571.10.1016/0001-6160(73)90064-3 ↗
41. M. Kato, T. Fujii, and S. Onaka: Mater. Sci. Eng., 2000, vol. A285, pp. 144–50.10.1016/S0921-5093(00)00639-0 ↗
42. M. Cherkaoui, H. Sabar, and M. Berveiller: J. Phys. III, 1994, vol. 4, pp. 719–32.10.1051/jp3:1994161 ↗
43. H. Sabar, M. Berveiller, and M. Buisson: C. R. Acad. Sci. Paris, 1990, vol. 310, Sér. II, pp. 447–52.
44. P. Gergaud, G. Dour, K. Inal, and J.L. Lebrun: Adv. X-ray Anal., 1997, vol. 39, pp. 225–35.
45. F. Eberl, G. Cailletaud, and J.L. Lebrun: Adv. X-ray Anal., 1998, vol. 42, pp. 116–21.
46. L. M’Cirdi, K. Inal, J.L. Lebrun, and G. Barbier: Acta Mater., 2001, vol. 49, pp. 3879–3987.10.1016/S1359-6454(01)00249-X ↗
47. C. Rey and P. Viaris De Lesegno: Mater. Sci. Eng., 1997, vol. A234–A236, pp. 1007–10.10.1016/S0921-5093(97)00383-3 ↗
48. F. Eberl, S. Forest, T. Wroblewski, G. Cailletaud, and J.L. Lebrun: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2825–33.10.1007/s11661-002-0268-1 ↗
49. L. M’Cirdi: Ph.D. Thesis, Ecole Nationale Supérieure des Arts et Métiers de Paris, Paris, 2000.
50. M. Sachtleber, Z. Zhao, and D. Raabe: Mater. Sci. Eng., 2002, vol. A336, pp. 81–87.10.1016/S0921-5093(01)01974-8 ↗
51. J.F. Nye: Acta Metall., 1953, vol. 1, pp. 153–62.10.1016/0001-6160(53)90054-6 ↗
52. K. Kondo: Memoirs on the Unifying Stdu of the Basic Problems in Engineering Sciences by Means of Geometry, K. Kondo, ed., Gakujutsu Bunken Fukyu-Kai, Tokyo, 1955, vol. 1, pp. 1–10.
53. E. Kröner: Kontinuumstheorie der Versetzungen and Eigenspannungen, Springer, Berlin, 1958.10.1007/978-3-642-94719-3 ↗
54. A.M. Kosevich: in Dislocations in Solids, F.R.N. Nabarro, ed., North Holland Publishing Company, Amsterdam, 1979, vol. 1, pp. 33–141.
55. J.W. Steeds and J.R. Willis: Dislocations in Solids, F.R.N. Nabarro, ed., North Holland Publishing Company, Amsterdam, 1979, vol. 1, pp. 143–65.
56. J.P. Hirth and J. Lothe: Theory of Dislocations, 2nd ed., Krieger Publishing Company, Malabar, FL, 1982.
57. C. Teodosiu: Elastic Models of Crystal Defects, Springer-Verlag, Bucharest, 1982.10.1007/978-3-662-11634-0 ↗
58. T. Mura: Micromechanics of Defects in Solids, Martinus Nijhoff Publishers. Kluwer, Dordrecht, The Netherlands, 1987.10.1007/978-94-009-3489-4 ↗
59. E. Kröner: Int. J. Solids Structures, 2001, vol. 38, pp. 1115–34.10.1016/S0020-7683(00)00077-9 ↗
60. V.V. Bulatov and L.P. Kubin: Current Opinion in Solid State and Materials Science, 1998, vol. 3, pp. 558–61.10.1016/S1359-0286(98)80025-9 ↗
61. V. Popov and E. Kröner: Comput. Mater. Sci., 1999, vol. 16, pp. 218–36.10.1016/S0927-0256(99)00065-8 ↗
62. A. Needleman and E. Van Der Giessen: Mater. Sci. Eng., 2001, vol. A309–A310, pp. 1–13.10.1016/S0921-5093(00)01684-1 ↗
63. P. Franciosi: Rev. Phys. Appl., 1988, vol. 23, p. 383.10.1051/rphysap:01988002304038300 ↗
64. P. Franciosi and A. Zaoui: Int. J. Plast., 1991, vol. 7, pp. 295–311.10.1016/0749-6419(91)90037-Y ↗
65. C. Schmitt, P. Lipinski, and M. Berveiller: Int. J. Plast., 1997, vol. 13, pp. 183–99.10.1016/S0749-6419(95)00007-0 ↗
66. M. Cherkaoui, M. Berveiller, and X. Lemoine: Int. J. Plast., 2000, vol. 16, p. 1215.10.1016/S0749-6419(00)00008-5 ↗
67. J.M. Sprauel and L. Castex: Proc. 1st EPDIC, Munich, 1991, p. 146.
68. H. Dölle: J. Appl. Cryst., 1979, vol. 12, p. 489.10.1107/S0021889879013169 ↗
69. J.M. Sprauel: Thèse de Docteur d’état es Sciences, Université Paris VI, Paris, 1988.
70. H.J. Bunge: Int. Mater. Rev., 1987, vol. 32 (6), pp. 265–91.10.1179/imr.1987.32.1.265 ↗
71. V. Hauk, W.K. Krug, R.W.M. Oudelhoven, and P. Pintschovius: Z. Metallkd., 1988, vol. 79, p. 159.
72. M. François: Ph.D. thesis, Ecole Nationale Supérieure des Arts et métiers de Paris, Paris, 1991.
73. J. Krier, M. Berveiller, P. Lipinski, and H. Ruppersberg: Text. Microstr., 1991, vols. 14–18, p. 1147.10.1155/TSM.14-18.1147 ↗
74. M. Ortiz and A. Pochettino: J. Nucl. Mater., 1994, vol. 229, p. 65.10.1016/0022-3115(95)00205-7 ↗
75. W.F. Hosford: The Mechanics of Crystals and Textured Polycrystals, Oxford University Press, New York, 1993.
76. H. Landolt and R. Börnstein: Springer-Verlag, Berlin, 1984, Gruppe III, Bands 11–18.
77. M. Belassel: Ph.D. Thesis, Ecole Nationale Supérieure des Arts et métiers de Paris, Paris, 1994.
78. B.M. Drapkin and B.V. Fokin: Phys. Met. Metall., 1980, vol. 49, p. 177.
79. J. Foct: Scripta Metall., 1993, vol. 29, p. 153.10.1016/0956-716X(93)90300-H ↗
80. H. Bougrab, K. Inal, and M. Berveiller: Mater. Sci. Forum, 2002, vols. 404–407, pp. 133–40.10.4028/www.scientific.net/MSF.404-407.133 ↗