Characterization of the Hot Deformation Behavior and Microstructure Evolution of a New γ-γ′ Strengthened Cobalt-Based Superalloy
Source abstract
Abstract
Recently, cobalt-based γ-γ′ microstructured superalloys have attracted attention. However, studies on their processing behavior [i.e., processing maps (the variation of strain rate sensitivity (m) with temperature)] are limited. Thus, the high-temperature flow behavior of a γ-γ′ Co-30Ni-10Al-5Mo-2Ta-2Ti-5Cr (at. pct) superalloy was investigated using isothermal compression tests between 1348 and 1498 K at strain rates from 0.001 to 10 s−1. The m contour map was generated using the experimental flow stress values, which were used to locate the optimum hot workability and desired microstructural processing range. A strong dependence of m on the deformation parameters (temperature, strain rate, and strain) was observed. A maximum m value of around 0.3 at 1460 K to 1498 K and strain rates of 0.01 to 0.5 s−1 was found. The deformed samples show a fully recrystallized microstructure at high m. Unstable domains showed the formation of cavities at the grain boundary triple points and cracks along the grain boundaries at high strain rates (1 to 10 s−1), corresponding to m < 0.10. A constitutive model was developed using an Arrhenius hyperbolic sine function, yielding an apparent activation energy of 540 ± 30 kJ mol−1 for hot deformation. This study indicates reasonable formability under certain conditions below the solvus, thus opening possibilities for further thermomechanical treatment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · High Temperature Alloys and Creep · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. A. S. M. International Handbook Committee, ASM Int. 1, 1993.
2. R.C. Reed: The Superalloys Fundamentals and Applications, Cambridge, Cambridge University Press, 2006.10.1017/CBO9780511541285 ↗
3. M. O. Alniak and F. Bedir: Mater. Des., 2010, vol. 31, pp. 1588-1592.10.1016/j.matdes.2009.09.020 ↗
4. J. W. Brooks, Mater. Des., 2000, vol. 21, pp. 297-303.10.1016/S0261-3069(99)00069-2 ↗
5. A. Dehghan-Manshadi, M. R. Barnett and P. D. Hodgson: Metall. Mater. Trans. A, 2008, vol. 39, pp. 1359-1370.10.1007/s11661-008-9512-7 ↗
6. F.J. Humphreys and M.Hatherly: Recrystallization and Related Annealing Phenomena, 2004.10.1016/B978-008044164-1/50016-5 ↗
7. D. Coutsouradis, A. Davin, and M. Lamberigts: Mater. Sci. Eng. A, 1987, vol. 88, pp. 11-19.10.1016/0025-5416(87)90061-9 ↗
8. D. L. Douglass, V. S. Bhide, and E. Vineberg: Oxid. Met., 1981, vol. 16, pp. 29-79.10.1007/BF00603744 ↗
9. N. Eliaz, G. Shemesh, and R. M. Latanision: Eng. Fail. Anal., 2002, vol. 9, pp. 31-43.10.1016/S1350-6307(00)00035-2 ↗
10. W. H. Jiang, X. D. Yao, H. R. Guan and Z. Q. Hu: J. Mater. Sci. Lett., 1999, vol. 8, pp. 303-05.10.1023/A:1006627122234 ↗
11. W.H Jiang, X. D. Yao, H. R. Guan, and Z. Q. Hu: J. Mater. Sci., 1999, vol. 4, pp. 2859-2864.10.1023/A:1004683301816 ↗
12. J. Sato, T. Omori, K. Oikawa, I. Ohnuma, R. Kainuma, and K. Ishida: Science., 2006, vol. 312, pp. 90-91.10.1126/science.1121738 ↗
13. S. K. Makineni, B. Nithin, and K. Chattopadhyay: Scr. Mater., 2015, vol. 98, pp. 36-39.10.1016/j.scriptamat.2014.11.009 ↗
14. A. Bauer, S. Neumeier, F. Pyczak, and M. Göken: Scr. Mater., 2010, vol. 63, pp.1197 -1200.10.1016/j.scriptamat.2010.08.036 ↗
15. G. Feng, H. Li, S. S. Li, and J. B. Sha: Scr. Mater., 2012, vol. 67, pp.499-502.10.1016/j.scriptamat.2012.06.013 ↗
16. F. B. Ismail, V. A. Vorontsov, T. C. Lindley, M. C. Hardy, D. Dye, and B. A. Shollock: Corros. Sci., 2017, vol. 116, pp. 44-52.10.1016/j.corsci.2016.12.009 ↗
17. L. Klein, A. Bauer, S. Neumeier, M. Göken, and S. Virtanen: Corros. Sci., 2011, vol. 53, pp. 2027-2034.10.1016/j.corsci.2011.02.033 ↗
18. Eric A. Lass, D. J. Sauza, D. C. Dunand, and D. N. Seidman: Acta Mater., 2018. vol. 147, pp. 284-295.10.1016/j.actamat.2018.01.034 ↗
19. T. M. Pollock, J. Dibbern, M. Tsunekane, J. Zhu, and A. Suzuki: JOM., 2010. vol. 62, pp. 58-63.10.1007/s11837-010-0013-y ↗
20. M.S. Titus, A. Suzuki, and T.M. Pollock: Superalloys, 2012, pp. 823–32.10.1002/9781118516430.ch91 ↗
21. H. Y. Yan, V. A. Vorontsov, and D. Dye: Intermetallics., 2014. vol. 48, pp. 44-53.10.1016/j.intermet.2013.10.022 ↗
22. H. Y. Yan, V. A. Vorontsov, and D. Dye: Corros. Sci., 2014. vol. 83, pp. 382-395.10.1016/j.corsci.2014.03.002 ↗
23. C. H. Zenk, S. Neumeier, H. J. Stone, and M. Göken: Intermetallics., 2014. vol. 55, pp. 28-39.10.1016/j.intermet.2014.07.006 ↗
24. S. K. Makineni, B. Nithin, and K. Chattopadhyay: Acta Mater., 2015, vol. 85, pp. 85-94.10.1016/j.actamat.2014.11.016 ↗
25. S. K. Makineni, A. Samanta, T. Rojhirunsakool, T. Alam, B. Nithin, A. K. Singh, R. Banerjee, and K. Chattopadhyay: Acta Mater., 2015, vol. 97, pp. 29-40.10.1016/j.actamat.2015.06.034 ↗
26. B. Nithin, A. Samanta, S. K. Makineni, T. Alam, P. Pandey, A. K. Singh, R. Banerjee, and K. Chattopadhyay: J. Mater. Sci., 2017, vol. 52, pp. 11036-11047.10.1007/s10853-017-1159-6 ↗
27. P. Pandey, S.K. Makineni, A.Samanta, A.Sharma, S.M. Das, C. Srivastava, B. Gault, D. Raabe, A.K, Singh, and K. Chattopadhyay, Under Prep., 2017.
28. A. N. Behera, A. Chaudhuri, R. Kapoor, J. K. Chakravartty, and S. Suwas: Mater. Des., 2016, vol. 92, pp. 750-759.10.1016/j.matdes.2015.12.077 ↗
29. R. Kapoor, J. K. Chakravartty, C. C. Gupta, and S. L. Wadekar: Mater. Sci. Eng. A., 2005, vol. 392, pp. 191-202.10.1016/j.msea.2004.09.023 ↗
30. S. Roy and S. Suwas: J. Alloys Compd., 2013, vol. 548, pp. 110-125.10.1016/j.jallcom.2012.08.123 ↗
31. R. Kapoor and J. K. Chakravartty: J. Nucl. Mater., 2002, vol. 306, pp. 126-133.10.1016/S0022-3115(02)01290-4 ↗
32. R. Kapoor, A.N. Behera, A. Sarkar, and J.K. Chakravartty: BARC Newsletter, 2015.
33. A. N. Behera, R. Kapoor, B. Paul, and J. K. Chakravartty: Mater. Charact., 2017, vol. 126, pp. 135-145.10.1016/j.matchar.2017.02.021 ↗
34. Y. V. R. K. Prasad, H. L. Gegel, S. M. Doraivelu, J. C. Malas, J. T. Morgan, K. a. Lark, and D. R. Barker: Metall. Trans. A., 1984, vol. 15, pp. 1883-1892.10.1007/BF02664902 ↗
35. S. Venugopal and S. L. Mannan: Mater. Sci. Eng. A., 1994, vol. 177, pp. 143-149.10.1016/0921-5093(94)90486-3 ↗
36. Y.V.R.K. Prasad and S. Sasidhara: Hot Working Guide: Compendium of Processing Maps, ASM International, Materials Park, OH, 1997.
37. Ika Kartika, H. Matsumoto, and A. Chiba: Metall. Mater. Trans. A., 2009, vol. 40, pp. 1457-1468.10.1007/s11661-009-9829-x ↗
38. V. A. Kumar, R. K. Gupta, S. V. S. N. Murty, and A. Durga: J. Alloys Compd., 2016, vol. 676, pp. 527-541.10.1016/j.jallcom.2016.03.186 ↗
39. A. Chiba, S. Lee, H. Matsumoto, and M. Nakamura: Mater. Sci. Eng. A., 2009, vol. 514, pp. 286-293.10.1016/j.msea.2009.02.044 ↗
40. T. Sakai: J. Mater. Process. Technol., 1995, vol. 53, pp. 349-361.10.1016/0924-0136(95)01992-N ↗
41. H. Jiang, J. Dong, M. Zhang, L. Zheng, and Z. Yao: J. Alloys Compd., 2015, vol.647, pp. 338-350.10.1016/j.jallcom.2015.05.192 ↗
42. C. M. Sellars, and W. J. Mctegart: Acta Mater., 1966, vol. 14, pp. 1136-1138.10.1016/0001-6160(66)90207-0 ↗
43. H. Y. Wu, F. J. Zhu, S. C. Wang, W. R. Wang, C. C. Wang, and C. H. Chiu: J. Mater. Sci., 2012, vol. 47, pp. 3971-3981.10.1007/s10853-012-6250-4 ↗
44. H. J. Mcqueen and N. D. Ryan: Mater. Sci. Eng. A., 2002, vol. 322, pp. 43-63.10.1016/S0921-5093(01)01117-0 ↗
45. B. Paul, R. Kapoor, J. K. Chakravartty, A. C. Bidaye, I. G. Sharma, and A. K. Suri: Scr. Mater., 2009, vol. 60, pp. 104-07.10.1016/j.scriptamat.2008.09.012 ↗
46. S. S. Satheesh Kumar, T. R. Pinaki, and P. B. G. Appa: J. Mater. Sci., 2015, vol. 50, pp. 6444-6456.10.1007/s10853-015-9200-0 ↗
47. H. Monajati, M. Jahazi, and A. K. Taheri: Metall. Mater. Trans. A., 2005, vol. 36, pp. 895-905.10.1007/s11661-005-0284-z ↗
48. H. Ziegler: Progress in Solid Mechanics, 1963, pp. 63–193.10.1007/BF00498655 ↗
49. P. C. J. Gallagher: Metall. Trans. A, 1970, vol. 1, pp. 2429-2461.10.1007/BF03038370 ↗
50. D. Li, Q. Guo, S. Guo, H. Peng, and Z. Wu: Mater. Des., 2011, vol. 32, pp. 696-705.10.1016/j.matdes.2010.07.040 ↗
51. S. Mitsche, C. Sommitsch, D. Huber, M. Stockinger, and P. Poelt: Mater. Forum., 2012, vol 709, pp. 2440-2445.10.4028/www.scientific.net/MSF.706-709.2440 ↗
52. G. R. Ebrahimi, A. Momeni, M. Jahazi, and P. Bocher: Metall. Mater. Trans. A ., 2014, vol. 45, pp. 2219-2231.10.1007/s11661-013-2119-7 ↗
53. L. Wang, F. Liu, J. J. Cheng, Q. Zuo, and C. F. Chen: J. Alloys Compd., 2015, vol. 623, pp. 69-78.10.1016/j.jallcom.2014.10.034 ↗
54. Y. Wu, M. Zhang, X. Xie, J. Dong, and F. Lin: J. Alloys Compd., 2016, vol. 656, pp. 119-131.10.1016/j.jallcom.2015.09.219 ↗
55. F. L. Sui, L. X. Xu, L. Q. Chen, and X. H. Liu: J. Mater. Process. Technol., 2011, vol. 211, pp. 433-440.10.1016/j.jmatprotec.2010.10.015 ↗
56. I. Kartika, Y. Li, H. Matsumoto, and A. Chiba: Mater. Trans., 2009, vol. 50, pp. 2277-2284.10.2320/matertrans.M2009103 ↗
57. P. K. Chaudhury, and Dan Zhao. Atlas of Formability Haynes 188, 1993.pp. 1-64.
58. S. Guo, D. Li, H. Pen, Q. Guo, and J. Hu: J. Nucl. Mater., 2011, vol. 410, pp.52-58.10.1016/j.jnucmat.2010.12.309 ↗
59. V. M. Sample, G. L. Fitzsimonss, and A. J. Deardo: Acta Mater., 1987, vol. 35, pp. 367-379.10.1016/0001-6160(87)90244-6 ↗