journal article·2017-08

Microstructural and Mechanical Evolution of a Low Carbon Steel by Friction Stir Processing

Dursun Murat Sekban, Semih Mahmut Aktarer, Hao Zhang, Peng Xue, Zongyi Ma, Gencaga Purcek

Publisher page

Abstract

A low carbon steel (Grade A) was subjected to friction stir processing (FSP), and the effect of FSP on the microstructure and mechanical properties was investigated systematically. It was found that two distinct zones called stir zone (SZ) and heat-effected zone (HAZ) were formed during FSP. The SZ and HAZ consist mainly of ferrite, widmanstatten ferrite, ferrite+cementite aggregates, and martensite. FSP considerably refined the microstructure of the steel by means of dynamic recrystallization mechanism and formed a volumetric defect-free basin-like processed region. The ferritic grain size of the steel decreased from 25 µm in the coarse-grained state to about 3 µm in the fine-grained state, and the grains formed were separated mostly by high angle of misorientation with low density of dislocations. This microstructural evolution brought about a considerable increase in both hardness and strength values without a considerable decrease in ductility. Ultrafine-grained microstructure formed around and just beneath the pin increased the hardness of the steel from 140 Hv0.3 to about 245 Hv0.3. However, no hardness uniformity was formed throughout the processed zone due to the changes in deformation- and temperature-induced microstructure. Both yield and tensile strength values of processed zone increased from 256 and 435 MPa to about 334 and 525 MPa, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. A. Ozekcin, H.W. Jin, J.Y. Koo, N. V Bangaru, R. Ayer and G. Vaughn, A: Int. J. Offshore Polar Eng., 2004, vol.14, pp. 1053–5381.
2. P. Xue, B.L. Xiao, W.G. Wang, Q. Zhang, D. Wang, Q.Z. Wang, et al.: Mater. Sci. Eng. A., 2013, vol.575, pp. 30–34.10.1016/j.msea.2013.03.033 ↗
3. G. Purcek, O. Saray, I. Karaman and T. Kucukomeroglu: Mater. Sci. Eng. A., 2008, vol.490, pp. 403–410.10.1016/j.msea.2008.01.080 ↗
4. A. Azushima, R. Kopp, A. Korhonen, D.Y. Yang, F. Micari, G.D. Lahoti, et al.: CIRP Ann. - Manuf. Technol., 2008, vol. 57, pp. 716–735.10.1016/j.cirp.2008.09.005 ↗
5. R.Z. Valiev and T.G. Langdon: Prog. Mater. Sci., 2006, vol. 51, pp. 881–981.10.1016/j.pmatsci.2006.02.003 ↗
6. S.M. Aktarer, D.M. Sekban, O. Saray, T. Kucukomeroglu, Z.Y. Ma and G. Purcek: Mater. Sci. Eng. A., 2015, vol. 636, pp. 311–319.10.1016/j.msea.2015.03.111 ↗
7. Z.Y. Ma: Metall. Mater. Trans. A., 2008, vol.39, pp. 642–658.10.1007/s11661-007-9459-0 ↗
8. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R Reports., 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
9. Y.N. Zhang, X. Cao, S. Larose and P. Wanjara: Can. Metall. Q., 2012, vol. 51, pp. 250–261.10.1179/1879139512Y.0000000015 ↗
10. H.S. Arora, H. Singh and B.K. Dhindaw: Int. J. Adv. Manuf. Technol., 2012, vol. 61, pp. 1043–1055.10.1007/s00170-011-3758-8 ↗
11. R.S. Mishra and Z.Y. Ma: Mater. Sci. Eng. R Reports., 2005, vol. 50, pp. 1–78.10.1016/j.mser.2005.07.001 ↗
12. Y.C. Chen and K. Nakata: Mater. Charact., 2009, vol. 60, pp. 1471–1475.10.1016/j.matchar.2009.07.004 ↗
13. D.M. Sekban, O. Saray, S.M. Aktarer, G. Purcek and Z.Y. Ma: Mater. Sci. Eng. A., 2015, vol. 642, pp. 57–64.10.1016/j.msea.2015.06.068 ↗
14. A. Chabok and K. Dehghani: Mater. Sci. Eng. A., 2010, vol. 528, pp. 309–313.10.1016/j.msea.2010.08.096 ↗
15. C. Lorenzo-Martin and O.O. Ajayi: Wear, 2015, vol. 332-333, pp. 962–970.10.1016/j.wear.2015.01.052 ↗
16. S.H. Aldajah, O.O. Ajayi, G.R. Fenske and S. David: Wear, 2009, vol. 267, pp. 350–355.10.1016/j.wear.2008.12.020 ↗
17. A. Rahbar-kelishami, A. Abdollah-zadeh, M.M. Hadavi, R. A. Seraj and A.P. Gerlich: Appl. Surf. Sci., 2014, vol. 316, pp. 501–507.10.1016/j.apsusc.2014.08.033 ↗
18. M.I. Costa, D. Verdera, M.T. Vieira and D.M. Rodrigues: Appl. Surf. Sci., 2014, vol. 296, pp. 214–220.10.1016/j.apsusc.2014.01.094 ↗
19. S. Khodir, Y. Morisada and H. Fujii: J. Mater. Sci., 2013, vol. 48, pp. 4313–4320.10.1007/s10853-013-7246-4 ↗
20. P. Xue, Z.Y. Ma, Y. Komizo and H. Fujii: Mater. Lett., 2016, vol. 162, pp. 161–164.10.1016/j.matlet.2015.09.115 ↗
21. M. Abbasi, T.W. Nelson and C.D. Sorensen: Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2012, vol. 43, pp. 4940–4946.10.1007/s11661-012-1356-5 ↗
22. N. Yasavol and H. Jafari: J. Mater. Eng. Perform., 2015, vol. 24, pp. 2151–2157.10.1007/s11665-015-1484-3 ↗
23. N. Yasavol, A. Abdollah-Zadeh, M.T. Vieira and H.R. Jafarian: Appl. Surf. Sci., 2014, vol. 293, pp. 151–159.10.1016/j.apsusc.2013.12.122 ↗
24. Y. Morisada, H. Fujii, T. Mizuno, G. Abe, T. Nagaoka and M. Fukusumi: Surf. Coatings Technol., 2011, vol. 205, pp. 3397–3403.10.1016/j.surfcoat.2010.11.062 ↗
25. M.H. Razmpoosh, A. Zarei-Hanzaki and A. Imandoust: Mater. Sci. Eng. A., 2015, vol. 638, pp. 15–19.10.1016/j.msea.2015.04.022 ↗
26. M.I. Costa, C. Leitão, A. Ramalho and D.M. Rodrigues: J. Mater. Process. Technol., 2015, vol. 217, pp. 272–277.10.1016/j.jmatprotec.2014.11.026 ↗
27. A. Amirafshar and H. Pouraliakbar: Meas. J. Int. Meas. Confed., 2015, vol. 68, pp. 111–116.10.1016/j.measurement.2015.02.051 ↗
28. R. Li, T. Yuan, Z. Qiu, K. Zhou and J. Li: Surf. Coat. Technol., 2014, vol. 258, pp. 415–425.10.1016/j.surfcoat.2014.08.059 ↗
29. H.S. Grewal, H.S. Arora, H. Singh, A. Agrawal and S. Mukherjee: J. Tribol., 2014, vol. 136, pp 1-10.10.1115/1.4027622 ↗
30. H.S. Grewal, H.S. Arora, H. Singh and A. Agrawal: Appl. Surf. Sci., 2013, vol. 268, pp. 547–555.10.1016/j.apsusc.2013.01.006 ↗
31. S. Noh, R. Kasada, A. Kimura, S.H.C. Park and S. Hirano: J. Nucl. Mater., 2011, vol. 417, pp. 245–248.10.1016/j.jnucmat.2011.01.059 ↗
32. M. Hajian, A. Abdollah-zadeh, S.S. Rezaei-Nejad, H. Assadi, S.M.M. Hadavi, K. Chung, et al.: Mater. Des., 2015, vol. 67, pp. 82–94.10.1016/j.matdes.2014.10.082 ↗
33. J.D. Escobar, E. Velásquez, T.F.A. Santos, A.J. Ramirez and D. López: Wear., 2013, vol. 297, pp. 998–1005.10.1016/j.wear.2012.10.005 ↗
34. S. Dodds, A.H. Jones and S. Cater: Wear., 2013, vol. 302, pp. 863–877.10.1016/j.wear.2013.01.007 ↗
35. M. Mehranfar and K. Dehghani: Mater. Sci. Eng. A., 2011, vol. 528, pp. 3404–3408.10.1016/j.msea.2011.01.016 ↗
36. Y.S. Sato, T.W. Nelson and C.J. Sterling: Acta Mater., 2005, vol. 53, pp. 637–645.10.1016/j.actamat.2004.10.017 ↗
37. International Institute for Welding Document IX-1533-88 IXJ-123-87 Revision 2, Guide to the Light Microscope Examination of Ferritic Steel Weld Metals., 1998.
38. M. Jafarzadegan, A.H. Feng, A. Abdollah-Zadeh, T. Saeid, J. Shen and H. Assadi: Mater. Charact., 2012, vol. 74, pp. 28–41.10.1016/j.matchar.2012.09.004 ↗
39. G. Thewlis: Mater. Sci. Technol., 2004, vol. 20, pp. 143–160.10.1179/026708304225010325 ↗
40. X. He, F. Gu and A. Ball: Prog. Mater. Sci., 2014, vol. 65, pp. 1–66.10.1016/j.pmatsci.2014.03.003 ↗
41. S. Tutunchilar, M. Haghpanahi, M.K.B. Givi, P. Asadi and P. Bahemmat: Mater. Des., 2012, vol. 40, pp. 415–426.10.1016/j.matdes.2012.04.001 ↗
42. K.N. Krishnan: Mater. Sci. Eng. A., 2002, vol. 327, pp. 246–251.10.1016/S0921-5093(01)01474-5 ↗
43. K. Kumar and S. V Kailas: Mater. Sci. Eng. A., 2008, vol. 485, pp. 367–374.10.1016/j.msea.2007.08.013 ↗
44. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, W.H. Bingel and R.A. Spurling: Metall. Mater. Trans. A., 1998, vol. 29, pp. 1955–1964.10.1007/s11661-998-0021-5 ↗
45. M.A. Sutton, B. Yang, A.P. Reynolds and R. Taylor: Mater. Sci. Eng. A., 2002, vol. 323, pp. 160–166.10.1016/S0921-5093(01)01358-2 ↗
46. T. Lienert and W.S. Jr: Weld. J. Res. Suppl., 2003, vol. 82, pp. 1–9.
47. J.-H. Cho, D.E. Boyce and P.R. Dawson: Mater. Sci. Eng. A., 2005, vol. 398, pp. 146–163.10.1016/j.msea.2005.03.002 ↗
48. P. Cizek, F. Bai, W.M. Rainforth and J.H. Beynon: Mater. Trans., 2004, vol. 45, pp. 2157–2164.10.2320/matertrans.45.2157 ↗
49. S.F. Di Martino and G. Thewlis: Metall. Mater. Trans. A., 2014, vol. 45, pp. 579–594.10.1007/s11661-013-2035-x ↗
50. P.L. Threadgill: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 357–360.10.1179/174329307X197629 ↗
51. J.C. Lippold: Welding Metallurgy and Weldability, Wiley, Ohio, USA, 2014.
52. J. Benjamin: Sci. Am., 1976, vol 234(5), pp. 40–48.10.1038/scientificamerican0576-40 ↗
53. B. Burton: Philos. Mag. A., 2002, vol. 82, pp. 2303–2320.10.1080/01418610208235740 ↗
54. I. Milas and E.A. Carter: J. Mater. Sci., 2009, vol. 44, pp. 1741.10.1007/s10853-008-3191-z ↗
55. C.B. Smith, W. Crusan, J.R. Hootman, J.F. Hinrichs, R.J. Heideman and J.S. Noruk: 2001 TMS Annu. Meet. Automot. Alloy. Join. Alum. Symp. (Aluminum 2001), 2001, pp. 175–185.
56. Y. Sugino, S. Ukai, B. Leng, N. Oono, S. Hayashi, T. Kaito, et al.: J. Nucl. Mater., 2014, vol. 452, pp. 628–632.10.1016/j.jnucmat.2014.05.040 ↗
57. J.-Q. Su, T.W. Nelson and C.J. Sterling: Mater. Sci. Eng. A., 2005, vol. 405, pp. 277–286.10.1016/j.msea.2005.06.009 ↗
58. P.B. Prangnell and C.P. Heason: Acta Mater., 2005, vol. 53, pp. 3179–3192.10.1016/j.actamat.2005.03.044 ↗