journal article·2017-04

Statistically Guided Development of Laser-Assisted Cold Spray for Microstructural Control of Ti-6Al-4V

Aaron M. Birt, Victor K. Champagne, Richard D. Sisson, Diran Apelian

Publisher page

Abstract

Laser-assisted cold spray (LACS) was used to deposit Ti-6Al-4V powders onto Ti-6Al-4V substrates using nitrogen as a carrier gas. An L25 orthogonal array was created with three parameters independent of particle velocity considered thus to be the independent thermal parameters (ITPs) of LACS: powder feed rate, raster speed, and laser power. A signal-to-noise analysis of the influence of the ITPs on porosity, microhardness, and expected thickness was performed revealing that optimum parameter selection is highly dependent on the targeted property, with the ITPs having the largest influence on porosity. Additional bulk trials (>2.5 mm thick) were deposited using parameters of interest from the orthogonal study. These scaled trials demonstrate that it is possible to produce deposits of Ti-6Al-4V via LACS using nitrogen as a carrier gas with porosity less than 1 pct, which is comparable with values described in literature for more expensive helium-based cold spray of Ti-6Al-4V. Additionally, variation of the ITPs indicates that secondary phases and morphologies can be produced and controlled through the thermomechanical treatment caused in situ to LACS.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Particle Dynamics in Fluid Flows

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. O. Dreier: Sourcing of Titanium for Airbus & the EADS, 2014.
2. Justin Hale: Aero Quarterly, Boeing.com Commercial Aeromagazine, 2006, vol. 4, pp. 17–23.
3. M.J. Donachie: Titanium: A Technical Guide, ASM International, 2000.10.31399/asm.tb.ttg2.9781627082693 ↗
4. S. Hodge: Report Information from Proquest, 2014.
5. Erhard Brandl, Frank Palm, Vesselin Michailov, Bernd Viehweger, and Christoph Leyens: Mater. Des., 2011, vol. 32, pp. 4665–75.10.1016/j.matdes.2011.06.062 ↗
6. Bernd Baufeld, Omer Van der Biest, and Rosemary Gault: Mater. Des., 2010, vol. 31, pp. S106–S111.10.1016/j.matdes.2009.11.032 ↗
7. M.B. Mathisen: Norwegian University of Science and Technology, Trondheim, Norway, Thesis, 2012.
8. Lore Thijs, Frederik Verhaeghe, Tom Craeghs, Jan Van Humbeeck, and Jean-Pierre Kruth: Acta Mater., 2010, vol. 58, pp. 3303–12.10.1016/j.actamat.2010.02.004 ↗
9. Thomas Vilaro, Christophe Colin, and Jean-Dominique Bartout: Metall. Mater. Trans. A, 2011, vol. 42, pp. 3190–99.10.1007/s11661-011-0731-y ↗
10. Eric Irissou, Jean-Gabriel Legoux, Anatoly Ryabinin, Bertrand Jodoin, and Christian Moreau: J. Therm. Spray Technol., 2008, vol. 17, pp. 495–516.10.1007/s11666-008-9203-3 ↗
11. T Stoltenhoff, H Kreye, and HJ Richter: J. Therm. Spray Technol., 2002, vol. 11, pp. 542–50.10.1361/105996302770348682 ↗
12. RM Molak, H Araki, M Watanabe, H Katanoda, N Ohno, and S Kuroda: J. Therm. Spray Technol., 2014, vol. 23, pp. 197–212.10.1007/s11666-013-0024-7 ↗
13. Gyuyeol Bae, Yuming Xiong, S Kumar, Kicheol Kang, and Changhee Lee: Acta Mater., 2008, vol. 56, pp. 4858–68.10.1016/j.actamat.2008.06.003 ↗
14. V.K. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, 1st ed., Woodhead: Cambridge, 2007.10.1533/9781845693787 ↗
15. Heli Koivuluoto, Andrew Coleman, Keith Murray, Martin Kearns, and Petri Vuoristo: J. Therm. Spray Technol., 2012, vol. 21, pp. 1065–75.10.1007/s11666-012-9790-x ↗
16. V.K. Champagne: Varying Reactive Material Properties and Their Effects on Energy Release, 2007.
17. Saden H Zahiri, Christian I Antonio, and Mahnaz Jahedi: J. Mater. Process. Technol., 2009, vol. 209, pp. 922–29.10.1016/j.jmatprotec.2008.03.005 ↗
18. Steve Yue, Ahmad Rezaeian, Jean Gabriel Legoux, Wilson Wong, and Eric Irissou: Adv. Mater. Res., 2010, vol. 89, pp. 639–44.
19. Wilson Wong, Eric Irissou, Anatoly N Ryabinin, Jean-Gabriel Legoux, and Stephen Yue: J. Therm. Spray Technol., 2011, vol. 20, pp. 213–26.10.1007/s11666-010-9568-y ↗
20. Gyuyeol Bae, Kicheol Kang, Jay-Jung Kim, and Changhee Lee: J. Mater. Sci. Eng. A, 2010, vol. 527, pp. 6313–19.10.1016/j.msea.2010.06.037 ↗
21. T Hussain: Key Eng. Mater., 2013, vol. 533, pp. 53–90.10.4028/www.scientific.net/KEM.533.53 ↗
22. J. Sieniawski, W. Ziaja, K. Kubiak, and M. Motyka: Titanium Alloys—Advances in Properties Control, Intech, 2013, Chapter 4. http://www.intechopen.com/books/titanium-alloys-advances-in-properties-control/microstructure-and-mechanical-properties-of-high-strength-two-phase-titanium-alloys10.5772/56197 ↗
23. W-Y Li, Chao Zhang, Xueping Guo, Jinling Xu, C-J Li, Hanlin Liao, Christian Coddet, and Khiam Aik Khor: Adv. Eng. Mater., 2007, vol. 9, pp. 418–23.
24. P. Vo, E. Irissou, J.-G. Legoux, and S. Yue: J. Therm. Spray Technol., 2013, pp. 1–11.
25. A.M. Birt, V.K. Champagne Jr., R.D. Sisson Jr., and D. Apelian: J. Therm. Spray Technol., 2015, pp. 1–12.
26. RE Blose, BH Walker, RM Walker, and SH Froes: Metal Powder Report, 2006, vol. 61, pp. 30–37.10.1016/S0026-0657(06)70713-5 ↗
27. Matthew Bray, Andrew Cockburn, and William O’Neill: Surf. Coat. Technol., 2009, vol. 203, pp. 2851–57.10.1016/j.surfcoat.2009.02.135 ↗
28. M Perton, S Costil, W Wong, D Poirier, E Irissou, J-G Legoux, A Blouin, and S Yue: J. Therm. Spray Technol., 2012, vol. 21, pp. 1322–33.10.1007/s11666-012-9812-8 ↗
29. B Samareh, O Stier, V Lüthen, and A Dolatabadi: J. Therm. Spray Technol., 2009, vol. 18, pp. 934–43.10.1007/s11666-009-9363-9 ↗
30. AP Alkhimov, VF Kosarev, and SV Klinkov: J. Therm. Spray Technol., 2001, vol. 10, pp. 375–81.10.1361/105996301770349466 ↗
31. Victor K Champagne, Dennis J Helfritch, Surya P G Dinavahi, and Phillip F Leyman: J. Therm. Spray Technol., 2011, vol. 20, pp. 425–31.10.1007/s11666-010-9530-z ↗
32. A. Birt, . Champagne, R. Sisson, and D. Apelian: Pittsburgh, PA, USA, in MS&T Conf., 2014.
33. G.F Vander Voort: Metallography: Principles and Practices, ASM International, 1984.10.31399/asm.tb.mpp.9781627082600 ↗
34. C.A. Schneider, W.S. Rasband, K.W. Eliceiri, others, Nat Methods, 2012, vol. 9, pp. 671–675.10.1038/nmeth.2089 ↗
35. Minitab: What is the signal-to-noise ratio in a Taguchi design? (2014), http://support.minitab.com. Accessed 12/26/2014.
36. T. Schmidt, F. Gärtner, H. Assadi, H. Kreye, Acta Materialia, 2006, vol. 54, pp. 729–742.10.1016/j.actamat.2005.10.005 ↗