journal article·2015-07

End Closure Joining of Ferritic-Martensitic and Oxide-Dispersion Strengthened Steel Cladding Tubes by Magnetic Pulse Welding

Jung-Gu Lee, Jin-Ju Park, Min-Ku Lee, Chang-Kyu Rhee, Tae-Kyu Kim, Alexey Spirin, Vasiliy Krutikov, Sergey Paranin

Publisher page

Abstract

The magnetic pulse welding (MPW) technique was employed for the end closure joining of fuel pin cladding tubes made of ferritic-martensitic (FM) steel and oxide-dispersion strengthened (ODS) steel. The technique is a solid-state impact joining process based on the electromagnetic force, similar to explosive welding. For a given set of optimal process parameters, e.g., the end-plug geometry, the rigid metallurgical bonding between the tube and end plug was obtained by high-velocity impact collision accompanied with surface jetting. The joint region showed a typical wavy morphology with a narrow grain boundary-like bonding interface. There was no evidence of even local melting, and only the limited grain refinement was observed in the vicinity of the bonding interface without destructing the original reinforcement microstructure of the FM-ODS steel, i.e., a fine grain structure with oxide dispersion. No leaks were detected during helium leakage test, and moreover, the rupture occurred in the cladding tube section without leaving any joint damage during internal pressure burst test. All of the results proved the integrity and durability of the MPWed joints and signified the great potential of this method of end closure joining for advanced fast reactor fuel pin fabrication.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fusion materials and technologies · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. R.L. Klueh and A.T. Nelson: J. Nucl. Mater., 2007, vol. 371, pp. 37-52.10.1016/j.jnucmat.2007.05.005 ↗
2. S. Kumar, R.P. Kushwaha, B.C. Maji, K. Bhanumurthy, and G.K. Dey: Metall. Mater. Trans. A, 2014, vol. 45A, pp. 531-6.10.1007/s11661-013-2151-7 ↗
3. C. Cayron, E. Rath, I. Chu, and S. Launois: J. Nucl. Mater., 2004, vol. 335, pp. 83-102.10.1016/j.jnucmat.2004.06.010 ↗
4. X. Boulnat, D. Fabregue, M. Perez, M.-H. Mathon, and Y. Decarlan: Metall. Mater. Trans. A, 2014, vol. 44A, pp. 2461-5.
5. A.A. Nikitina, V.S. Ageev, A.P. Chukanov, V.V. Tsvelev, N.P. Porezanov, and O.A. Kruglov: J. Nucl. Mater., 2012, vol. 428, pp. 117-24.10.1016/j.jnucmat.2012.02.022 ↗
6. V.G. Krishnardula, N.I. Sofyan, W.F. Gale, and J.W. Fergus: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 497-500.10.1007/s11661-006-0021-2 ↗
7. M. Seki, K. Hirako, S. Kono, Y. Kihara, T. Kaito, and S. Ukai: J. Nucl. Mater., 2004, vol. 329-333, pp. 1534-8.10.1016/j.jnucmat.2004.04.172 ↗
8. D. Dean and M. Hidekazu: Comput. Mater. Sci., 2006, vol. 37, pp. 209-19.10.1016/j.commatsci.2005.06.010 ↗
9. S. Noh, R. Kasada, N. Oono, N. Iwata, and A. Kimura: Fusion Eng. Design, 2010, vol. 85, pp. 1033-7.10.1016/j.fusengdes.2010.01.001 ↗
10. R.N. Raoelison, N. Buiron, M. Rachik, D. Haye, G. Franz, and M. Habak: J. Mater. Process. Technol., 2013, vol. 213, pp. 1348-54.10.1016/j.jmatprotec.2013.03.004 ↗
11. J. Y. Shim, I. S. Kim, K. J. Lee, and B. Y. Kang: Met. Mater. Int., 2011, vol. 17, pp. 957-61.10.1007/s12540-011-6014-8 ↗
12. Y. Zhang, S.S. Babu, C. Prothe, M. Blakely, J. Kwasegroch, M. LaHa, and G.S. Daehn: J. Mater. Process. Technol., 2011, vol. 211, pp. 944-52.10.1016/j.jmatprotec.2010.01.001 ↗
13. J.H. Kim and S.H. Kim: J. Nucl. Mater., 2013, vol. 443, pp. 112-9.10.1016/j.jnucmat.2013.06.051 ↗
14. T. Jayakumar, M.D. Mathew, K. Laha, and R. Sandhya: Nucl. Eng. Des., 2013, vol. 265, pp. 1175-80.10.1016/j.nucengdes.2013.05.001 ↗
15. V. Krutikov, S. Paranin, V. Ivanov, A. Spirin, D. Koleukh, J.G. Lee, M.K. Lee, and C.K. Rhee: 6th Int. Conf. High Speed Forming, Daejeon, Korea, 2014, pp. 207–14.
16. K.J. Lee, S. Kumai, T. Arai, and T. Aizawa: Mater. Sci. Eng. A, 2007, vol. A471, pp. 95-101.10.1016/j.msea.2007.04.033 ↗
17. M. Watanabe and S. Kumai: Mater. Trans., 2009, vol. 50, pp. 286-92.10.2320/matertrans.L-MRA2008843 ↗
18. A.P. Manogaran, P. Manoharan, D. Priem, S. Marya, and G. Racineux: J. Mater. Process. Technol., 2014, vol. 214, pp. 1236-44.10.1016/j.jmatprotec.2014.01.007 ↗
19. A. Durgutlu, H. Okuyucu, and B. Gulenc: Mater. Des., 2008, vol. 29, pp. 1480-4.10.1016/j.matdes.2007.07.012 ↗
20. Y. Iwahashi, Z. Horita, M. Nemoto, and T.G. Langdon: Acta Mater., 1998, vol. 46, pp. 3317-31.10.1016/S1359-6454(97)00494-1 ↗
21. Y. Zhang, S.S. Babu, and G.S. Daehn: J. Mater. Sci., 2010, vol. 45, pp. 4645-51.10.1007/s10853-010-4676-0 ↗