journal article·2017-10

Fabrication and Tribological Behavior of Stir Cast Mg/B4C Metal Matrix Composites

Amandeep Singh, Niraj Bala

Publisher page

Abstract

Magnesium-based metal matrix composites (MMMCs) have emerged as good alternative material to conventional materials due to their promising advanced properties. In the present work, magnesium-based metal matrix composites (MMMCs) reinforced with B4C particles were successfully fabricated by cost-effective conventional stir casting technique. MMMCs with an average particle size of 63 µm and different weight percent (wt pct) of B4C between 3 and 12 were fabricated. Wear tests were carried out using a pin-on-disk against a steel disk under dry sliding condition at loads that varied between 1 and 5 kg at fixed sliding velocity of 1 m/s. The wear data clearly showed that wear resistance of cast composites is better than that of unreinforced magnesium, which is attributed to dispersion hardening caused by carbide particles. An increase in wt pct of B4C showed the wear resistance and hardness to increase significantly. The wear rate and coefficient of friction increased with an increase in applied load. The SEM and EDS analysis of the worn surfaces delineated the dominant wear mechanisms to be abrasion, adhesion, and oxidation under the different sliding conditions. At lower loads, the wear mechanism transformed from severe abrasive wear in pure magnesium (Mg) to mild abrasion, slight delamination, and oxidation in the Mg/12 wt pct B4C fabricated composite. At higher loads, severe abrasion, adhesion, delamination, and oxidation were found to be the major wear mechanisms in pure Mg, whereas in the Mg/12 wt pct B4C fabricated composites the corresponding mechanisms were mild abrasion, mild adhesion, slight delamination, and oxidation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Magnesium Alloys: Properties and Applications · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. H.Z. Ye and X.Y. Liu, Journal of Materials Science 2004, vol. 39, pp. 6153-6171.10.1023/B:JMSC.0000043583.47148.31 ↗
2. L. Chen and Y. Yao, Acta Metallurgica Sinica (English Letters) 2014, vol. 27, pp. 762-774.10.1007/s40195-014-0161-0 ↗
3. P. Rohatgi, JOM 1991, vol. 43, pp. 10-15.10.1007/BF03220538 ↗
4. B. V. Ramnath, C. Elanchezhian, R. Annamalai, S. Aravind, T. S. A. Atreya, V. Vignesh and C. Subramanian, Mater. Sci 2014, vol. 38, pp. 55-60.
5. S. R. Yu and Z. Q. Huang, Journal of Materials Engineering and Performance 2014, vol. 23, pp. 3480-3488.10.1007/s11665-014-1157-7 ↗
6. S.-J. Huang, Y.-R. Jeng, V. I. Semenov and Y.-Z. Dai, Tribology Letters 2011, vol. 42, pp. 79-87.10.1007/s11249-011-9751-4 ↗
7. K. Xiu, H. Y. Wang, H. L. Sui, Y. Wang, C. L. Xu, J. G. Wang and Q. C. Jiang, Journal of Materials Science 2006, vol. 41, pp. 7052-7058.10.1007/s10853-006-0946-2 ↗
8. J. Yao, W. Li, L. Zhang, F. Wang, M. Xue, H. Jiang and J. Lu, Tribology letters 2010, vol. 38, pp. 253-257.10.1007/s11249-010-9600-x ↗
9. M. Abbasi, B. Bagheri, M. Dadaei, H. R. Omidvar and M. Rezaei, The International Journal of Advanced Manufacturing Technology 2015, vol. 77, pp. 2051-2058.10.1007/s00170-014-6577-x ↗
10. T. Chen, Z. Zhu, Y. Ma, Y. Li and Y. Hao, Journal of Wuhan University of Technology-Mater. Sci. Ed. 2010, vol. 25, pp. 223-227.10.1007/s11595-010-2223-0 ↗
11. G. M. Reddy, A. S. Rao and K. S. Rao, Transactions of the Indian Institute of Metals 2013, vol. 66, pp. 13-24.10.1007/s12666-012-0163-4 ↗
12. S. K. Jo, W. J. Lee, Y. H. Park and I. M. Park, Tribology Letters 2012, vol. 45, pp. 101-107.10.1007/s11249-011-9866-7 ↗
13. C. Lim, S. Lim and M. Gupta, Wear 2003, vol. 255, pp. 629-637.10.1016/S0043-1648(03)00121-2 ↗
14. Q. Jiang, H. Wang, B.-X. Ma, Y. Wang and F. Zhao, Journal of Alloys and Compounds 2005, vol. 386, pp. 177-181.10.1016/j.jallcom.2004.06.015 ↗
15. G. Arslan, F. Kara and S. Turan, Journal of the European Ceramic Society 2003, vol. 23, pp. 1243-1255.10.1016/S0955-2219(02)00304-7 ↗
16. P. Poddar, V. C. Srivastava, P. K. De and K. L. Sahoo, Materials Science and Engineering: A 2007, vol. 460–461, pp. 357-364.10.1016/j.msea.2007.01.052 ↗
17. R. Saravanan and M. Surappa, Materials Science and Engineering: A 2000, vol. 276, pp. 108-116.10.1016/S0921-5093(99)00498-0 ↗
18. M. Balakrishnan, I. Dinaharan, R. Palanivel and R. Sivaprakasam, Journal of Magnesium and Alloys 2015, vol. 3, pp. 76-78.10.1016/j.jma.2014.12.007 ↗
19. Q. Jiang, X. Li and H. Wang, Scripta Materialia 2003, vol. 48, pp. 713-717.10.1016/S1359-6462(02)00551-1 ↗
20. L. F. Guleryuz, S. Ozan, D. Uzunsoy and R. Ipek, Acta Physica Polonica A 2013, vol. 123, pp. 488-489.10.12693/APhysPolA.123.488 ↗
21. S. Yu and Z. Huang, Journal of Materials Engineering and Performance 2014, vol. 23, pp. 3480-3488.10.1007/s11665-014-1157-7 ↗
22. J. Archard, Journal of applied physics 1953, vol. 24, pp. 981-988.10.1063/1.1721448 ↗
23. Q.-J. Qi, Transactions of nonferrous metals society of china 2006, vol. 16, pp. 1135-1140.10.1016/S1003-6326(06)60390-7 ↗
24. H. Yong and R. Li, Transactions of Nonferrous Metals Society of China 2012, vol. 22, pp. 2659-2664.10.1016/S1003-6326(11)61514-8 ↗
25. Z. Zhenfang, Z. Liangchi and M. Yiu-Wing, Wear 1994, vol. 176, pp. 231-237.10.1016/0043-1648(94)90151-1 ↗
26. P. Asadi, G. Faraji, A. Masoumi and M. K. Givi, Metall. Mater. Trans. A 2011, vol. 42A, pp. 2820-2832.10.1007/s11661-011-0698-8 ↗
27. L. Falcon-Franco, E. Bedolla-Becerril, J. Lemus-Ruiz, J. G. Gonzalez-Rodríguez, R. Guardian and I. Rosales, Composites Part B: Engineering 2011, vol. 42, pp. 275-279.10.1016/j.compositesb.2010.11.012 ↗
28. H. Arora, H. Singh and B. Dhindaw, Wear 2013, vol. 303, pp. 65-77.10.1016/j.wear.2013.02.023 ↗
29. M. Srinivasan, C. Loganathan, M. Kamaraj, Q. Nguyen, M. GUPTA and R. Narayanasamy, Transactions of Nonferrous Metals Society of China 2012, vol. 22, pp. 60-65.10.1016/S1003-6326(11)61140-0 ↗
30. S. Sharma, B. Anand and M. Krishna, Wear 2000, vol. 241, pp. 33-40.10.1016/S0043-1648(00)00349-5 ↗
31. G. Gertsberg, E. Aghion, A. A. Kaya and D. Eliezer, Journal of Materials Engineering and Performance 2009, vol. 18, pp. 886-892.10.1007/s11665-008-9306-5 ↗