journal article·2011-07

Effects of Rolling and Cooling Conditions on Microstructure and Tensile and Charpy Impact Properties of Ultra-Low-Carbon High-Strength Bainitic Steels

Hyo Kyung Sung, Sang Yong Shin, Byoungchul Hwang, Chang Gil Lee, Nack J. Kim, Sunghak Lee

Publisher page

Abstract

Six ultra-low-carbon high-strength bainitic steel plates were fabricated by controlling rolling and cooling conditions, and effects of bainitic microstructure on tensile and Charpy impact properties were investigated. The microstructural evolution was more critically affected by start cooling temperature and cooling rate than by finish rolling temperature. Bainitic microstructures such as granular bainites (GBs) and bainitic ferrites (BFs) were well developed as the start cooling temperature decreased or the cooling rate increased. When the steels cooled from 973 K or 873 K (700 °C or 600 °C) were compared under the same cooling rate of 10 K/s (10 °C/s), the steels cooled from 973 K (700 °C) consisted mainly of coarse GBs, while the steels cooled from 873 K (600 °C) contained a considerable amount of BFs having high strength, thereby resulting in the higher strength but the lower ductility and upper shelf energy (USE). When the steels cooled from 673 K (400 °C) at a cooling rate of 10 K/s (10 °C/s) or 0.1 K/s (0.1 °C/s) were compared under the same start cooling temperature of 873 K (600 °C), the fast cooled specimens were composed mainly of coarse GBs or BFs, while the slowly cooled specimens were composed mainly of acicular ferrites (AFs). Since AFs had small effective grain size and contained secondary phases finely distributed at grain boundaries, the slowly cooled specimens had a good combination of strength, ductility, and USE, together with very low energy transition temperature (ETT).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. J.Y. Koo, M.J. Luton, N.V. Bangaru, R.A. Petkovic, D.P. Fairchild, C.W. Petersen, H. Asahi, T. Hara, Y. Terada, M. Sugiyama, H. Tamehiro, Y. Komizo, S. Okaguchi, M. Hamada, A. Yamamoto, and I. Takeuchi: Proc. 13th Int. Offshore and Polar Engineering Conf., Honolulu, HI, International Society of Offshore and Polar Engineers, Cupertino, CA, 2003, pp. 10–18.
2. B.L. Bramfitt and J.G. Speer: Metall. Trans. A, 1990, vol. 21A, pp. 817–29.10.1007/BF02656565 ↗
3. H. Ohtani, S. Okaguchi, Y. Fujishiro, and Y. Ohmori: Metall. Trans. A, 1990, vol. 21A, pp. 877–88.10.1007/BF02656571 ↗
4. T. Araki: Atlas for Bainitic Microstructures, ISIJ, Tokyo, 1992, pp. 1–100.
5. G. Krauss and S.W. Thompson: ISIJ Int., 1995, vol. 35, pp. 937–45.10.2355/isijinternational.35.937 ↗
6. H.K.D.H. Bhadeshia: Mater. Sci. Eng., 2004, vol. A378, pp. 34–39.10.1016/j.msea.2003.10.328 ↗
7. C. Garcia-Mateo, M. Peet, F.G. Caballero, and H.K.D.H. Bhadeshia: Mater. Sci. Technol., 2004, vol. 20, pp. 814–18.10.1179/026708304225017355 ↗
8. C.H. Lee, H.K.D.H. Bhadeshia, and H.-C. Lee: Mater. Sci. Eng., 2003, vol. A360, pp. 249–57.10.1016/S0921-5093(03)00477-5 ↗
9. S. Han, H. Seong, Y. Ahn, C.I. Garcia, A.J. DeArdo, and I. Kim: Met. Mater. Int., 2009, vol. 15, pp. 521–29.10.1007/s12540-009-0521-x ↗
10. S.Y. Han, S.Y. Shin, S. Lee, J. Bae, and K. Kim: Metall. Mater. Trans. A, 2010, vol. 41A, pp. 329–40.10.1007/s11661-009-0135-4 ↗
11. R. Denys: Pipeline Technology Conf., Elsevier, Amsterdam, The Netherlands, 2000, vols. 1–II, pp. 1–116.
12. U.S. Patent No. 200,701,936,662,007, 2007.10.1086/512765 ↗
13. U.G. Gang, J.C. Lee, and W.J. Nam: Met. Mater. Int., 2009, vol. 15. pp. 719–25.10.1007/s12540-009-0719-3 ↗
14. T. Hara, Y. Shinohara, Y. Terada, and H. Asahi: Proc. 18th Int. Offshore and Polar Engineering Conf., Vancouver, BC, Canada, International Society of Offshore and Polar Engineers, Cupertino, CA, 2008, pp. 73–79.
15. D.B. Lillig: Proc. 18th Int. Offshore and Polar Engineering Conf., Vancouver, BC, Canada, International Society of Offshore and Polar Engineers, Cupertino, CA, 2008, pp. 1–12.
16. I. Tamura, H. Sekine, T. Tanaka, and C. Ouchi: Thermomechanical Processing of High-Strength Low-Alloy Steels, Butterworth & Co., Ltd., London, 1988, pp. 80–100.10.1016/B978-0-408-11034-1.50007-6 ↗
17. M. Diaz-Fuentes, A. Iza-Mendia, and I. Gutierrez: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2505–16.10.1007/s11661-003-0010-7 ↗
18. ASTM Standard E8m-09: Standard Test Methods for Tension Testing of Metallic Materials, Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2009.
19. ASTM Standard E23-09: Standard Test Method for Notched Bar Impact Testing of Metallic Materials, Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2009.
20. W. Oldfield: Curve Fitting Impact Test Data—a Statistical Procedure, ASTM Standardization News, West Conshohocken, PA, 1975, pp. 24–29.
21. J.M. Jang, S.J. Kim, N.H. Kang, K.M. Cho, and D.W. Suh: Met. Mater. Int., 2009, vol. 15, pp. 909–16.10.1007/s12540-009-0909-7 ↗
22. H.W. Swift: J. Mech. Phys. Solids, 1952, vol. 1, pp. 1–16.10.1016/0022-5096(52)90002-1 ↗
23. J.H. Hollomon: Trans. AIME, 1945, vol. 162, pp. 268–90.
24. B.-W. Choi, D.-H. Seo, and J.-I. Jang: Met. Mater. Int., 2009, vol. 15, pp. 373–78.10.1007/s12540-009-0373-4 ↗
25. S.K. Kim, Y.M. Kim, Y.J. Lim, and N.J. Kim: Proc. 15th Conf. on Mechanical Behaviors of Materials, Korea Institute of Metals and Materials, Seoul, 2001, pp. 177–86.
26. N.J. Kim : Mater. Sci. Eng., 1990, vol. A129, pp. 35–44.10.1016/0921-5093(90)90342-Z ↗
27. H.K. Sung, S.Y. Shin, B. Hwang, C.G. Lee, N.J. Kim, and S. Lee: J. Kor. Inst. Met. Mater., 2010, vol. 48, pp. 615–24.
28. Y. Ohomori, H. Ohtani, and T. Kunitake: Met. Sci., 1974, vol. 8, pp. 357–66.10.1016/0036-9748(74)90138-0 ↗
29. F.B. Pickering and T. Gladman: ISI Spec. Rep., 1961, vol. 81, pp. 10–20.