journal article·2015-09

On the Achievement of Nanostructured Interstitial Free Steel by Four-Layer Accumulative Roll Bonding Process at Room Temperature

Roohollah Jamaati, Mohammad Reza Toroghinejad, Sajjad Amirkhanlou, Hossein Edris

Publisher page

Abstract

In this study, the four-layer accumulative roll bonding (ARB) process at room temperature for nanostructuring the interstitial free (IF) steel was used for the first time. Hardness and tensile tests were performed and the microstructure was characterized using scanning transmission electron microscopy. It was found that the grain size decreased into the nanostructured domain after fourth cycle, reaching grain sizes of smaller than 100 nm. The stored energy was retained in the material until the continuous dynamic recrystallization led to nanostructuring of the IF steel. The dislocation density was measured by microhardness indentation size effect using the Nix–Gao model. The results indicated that an increase in the number of ARB cycles leads to increase in the dislocation density. The dislocation density increased from 2.02 × 109 cm−2 for initial sample to 9.47 × 109 cm−2 after fourth cycle. The yield strength of the IF steel after fourth cycle was 10.8 times (909 MPa) higher than that of the initial sample (84 MPa). Finally, the contribution of individual mechanisms such as the grain refinement, dislocation, and precipitation in strengthening of the IF steel were evaluated.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Metal Alloys Wear and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. [1] R.Z. Valiev: Nat. Mater., 2004, vol. 3, pp. 511-6.10.1038/nmat1180 ↗
2. [2] R.Z. Valiev, A.V. Korznikov, and R.R. Mulyukov: Mater. Sci. Eng. A, 1993, vol. 168, pp. 141-8.10.1016/0921-5093(93)90717-S ↗
3. [3] M.J. Zehetbauer and Y.T. Zhu: Bulk Nanostructured Materials, Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim, Germany, 2009.10.1002/9783527626892 ↗
4. [4] R.Z. Valiev and T.G. Langdon: Progr. Mater. Sci., 2006, vol. 51, pp. 881-981.10.1016/j.pmatsci.2006.02.003 ↗
5. [5] R.Z. Valiev, R.K. Islamgaliev, and I.V. Alexandrov: Progr. Mater. Sci., 2000, vol. 45, pp. 103-89.10.1016/S0079-6425(99)00007-9 ↗
6. [6] A.P. Zhilyaev and T.G. Langdon: Progr. Mater. Sci., 2008, vol. 53, pp. 893-979.10.1016/j.pmatsci.2008.03.002 ↗
7. [7] A. Azushima, R. Kopp, A. Korhonen, D.Y. Yang, F. Micari, G.D. Lahoti, P. Groche, J. Yanagimoto, N. Tsuji, A. Rosochowski, and A. Yanagida: CIRP Annals–Manufact. Tech., 2008, vol. 57, pp. 716-35.10.1016/j.cirp.2008.09.005 ↗
8. [8] R. Jamaati, M.R. Toroghinejad, J. Dutkiewicz, and J.A. Szpunar: Mater. Design, 2012, vol. 35, pp. 37-42.10.1016/j.matdes.2011.09.040 ↗
9. [9] C.W. Schmidt, C. Knieke, V. Maier, H.W. Hoppel, W. Peukert, and M. Goken: Scripta Mater., 2011, vol. 64, pp. 245-8.10.1016/j.scriptamat.2010.10.013 ↗
10. [10] R. Jamaati, M.R. Toroghinejad, and H. Edris: Mater. Sci. Eng. A, 2013, vol. 583, pp. 20-4.10.1016/j.msea.2013.06.068 ↗
11. [11] M. Rezayat, A. Akbarzadeh, and A. Owhadi: Metall. Mater. Trans. A, 2012, vol. 43, pp. 2085-93.10.1007/s11661-011-1039-7 ↗
12. [12] R. Jamaati, M.R. Toroghinejad, and H. Edris: Mater. Design, 2014, vol. 54, pp. 168-73.10.1016/j.matdes.2013.08.033 ↗
13. [13] M. Alizadeh and M.H. Paydar: J. Alloy. Compd., 2010, vol. 492, pp. 231-5.10.1016/j.jallcom.2009.12.026 ↗
14. [14] Y. Saito, N. Tsuji, H. Utsunomiya, T. Sakai, and R.G. Hong: Scripta Mater., 1998, vol. 39, pp. 1221-7.10.1016/S1359-6462(98)00302-9 ↗
15. [15] M.R. Toroghinejad, F. Ashrafizadeh, and R. Jamaati: Mater. Sci. Eng. A, 2013, vol. 561, pp. 145-51.10.1016/j.msea.2012.11.010 ↗
16. [16] Y. Saito, H. Utsunomiya, N. Tsuji, and T. Sakai: Acta Mater., 1999, vol. 47, pp. 579-83.10.1016/S1359-6454(98)00365-6 ↗
17. [17] M. Raei, M.R. Toroghinejad, and R. Jamaati: Mater. Manufact. Process., 2011, vol. 26, pp. 1352-6.10.1080/10426914.2011.557133 ↗
18. [18] M. Shaarbaf and M.R. Toroghinejad: Mater. Sci. Eng. A, 2008, vol. 473, pp. 28-33.10.1016/j.msea.2007.03.065 ↗
19. [19] S. Pasebani and M.R. Toroghinejad: Mater. Sci. Eng. A, 2010, vol. 527, pp. 491-7.10.1016/j.msea.2009.09.029 ↗
20. [20] N. Tsuji, Y. Saito, H. Utsunomiya, and S. Tanigawa: Scripta Mater., 1999, vol. 40, pp. 795-800.10.1016/S1359-6462(99)00015-9 ↗
21. [21] S.H. Lee, H. Utsunomiya, and T. Sakai: Mater. Trans., 2004, vol. 45, pp. 2177-81.10.2320/matertrans.45.2177 ↗
22. [22] S. Tamimi, M. Ketabchi, and N. Parvin: Mater. Design, 2009, vol. 30, pp. 2556-62.10.1016/j.matdes.2008.09.039 ↗
23. [23] G. Krallics and J.G. Lenard: J. Mater. Process. Tech., 2004, vol. 152, pp. 154-61.10.1016/j.jmatprotec.2004.03.015 ↗
24. [24] G. Purcek, O. Saray, I. Karman, and H.J. Maier: Metall. Mater. Trans. A, 2012, vol. 43, pp. 1884-94.10.1007/s11661-011-1063-7 ↗
25. [25] O. Saray, G. Purcek, I. Karaman, T. Neindorf, and H.J. Maier: Mater. Sci. Eng. A, 2011, vol. 528, pp. 6573-83.10.1016/j.msea.2011.05.014 ↗
26. [26] R. Jamaati, M.R. Toroghinejad, H. Edris, and M.R. Salmani: Mater. Design, 2014, vol. 56, pp. 359-67.10.1016/j.matdes.2013.11.049 ↗
27. [27] T. Sakai, A. Belyakov, R. Kaibyshev, H. Miura, and J.J. Jonas: Progr. Mater. Sci., 2014, vol. 60, pp. 130-207.10.1016/j.pmatsci.2013.09.002 ↗
28. [28] F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier Science Ltd., Oxford, U.K., 2004.
29. [29] W.D. Nixand H. Gao: J. Mech. Phys. Solids, 1998, vol. 46, pp. 411-25.10.1016/S0022-5096(97)00086-0 ↗
30. [30] S. Graca, R. Colaco, P.A. Carvalho, and R. Vilar: Mater. Lett., 62 (2008, pp. 3812–3814.10.1016/j.matlet.2008.04.072 ↗
31. [31] W.D. Callister and D.G. Rethwisch: Materials Science Engineering: An Introduction, 8th ed., John Wiley and Sons, New York, NY, 2010.
32. [32] D.R. Askeland, P.P. Fulay, and W.J. Wright: The Science and Engineering of Materials, 6th ed., Cengage Learning, Stamford, CT, 2011.
33. [33] A. Sarkar, A. Bhowmik, and S. Suwas: Appl. Phys. A, 2009, vol. 94, pp. 943-8.10.1007/s00339-008-4870-y ↗
34. [34] B.L. Li, A. Godfrey, Q.C. Meng, Q. Liu, and N. Hansen: Acta Mater., 2004, vol. 52, pp. 1069-81.10.1016/j.actamat.2003.10.040 ↗