journal article·2018-11

Effect of Stress Relieving Heat Treatment on the Microstructure and High-Temperature Compressive Deformation Behavior of Ti-6Al-4V Alloy Manufactured by Selective Laser Melting

Young-Kyun Kim, Soon-Hong Park, Yong-Jin Kim, Bandar Almangour, Kee-Ahn Lee

Publisher page

Abstract

This study aims to investigate the effect of stress relieving heat treatment on the microstructure and high-temperature compressive deformation behavior of the Ti-6Al-4V alloy, manufactured by selective laser melting. Initial microstructural observation confirmed elongated prior β grains in the building direction of both specimens (as-fabricated and heat-treated specimens). Along with such, the as-fabricated specimen only featured α′-martensite phase, while the heat-treated specimen featured α′-martensite and some α and β phases. Compression tests carried out at room temperature gave yield strengths of 1365 and 1138 MPa for the as-fabricated and heat-treated specimens, respectively. Such values are similar or greater than those of commercial wrought materials. The compressive fracture strain significantly increased after heat treatment. There was a general tendency of reducing yield strength as compressive temperatures increased. At temperatures greater than 700 °C, the as-fabricated and heat-treated specimens achieved similar strength. Microstructural observation after deformation confirmed that the initial microstructure was retained up to temperatures of 500 °C. At 700 °C or greater, both specimens showed drastic microstructural evolution.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. M. Vaezi, H. Seitz, and S. Yang: Int. J. Adv. Manuf. Technol., 2013, vol. 67, pp. 1721–54.10.1007/s00170-012-4605-2 ↗
2. L. Facchini, E. Magalini, and P. Robotti: Rapid Prototyp. J., 2009, vol. 15, pp. 171–78.10.1108/13552540910960262 ↗
3. C. Qiu, N.J.E. Adkins, and M.M. Attallah: Mater. Sci. Eng. A, 2013, vol. 578, pp. 230–39.10.1016/j.msea.2013.04.099 ↗
4. E.J. Bae, J.H. Kim, W.C. Kim, and H.Y. Kim: J. Adv. Prosthodont., 2014, vol. 6, pp. 266–71.10.4047/jap.2014.6.4.266 ↗
5. B. Nie, H. Huang, S. Bai, and J. Liu: Appl. Phys. A, 2015, vol. 118, pp. 37–41.10.1007/s00339-014-8897-y ↗
6. S. Bremen, W. Meiners, and A. Diatlov: Laser Techn. J., 2012, vol. 9, pp. 33–38.10.1002/latj.201290018 ↗
7. F. Abe, K. Osakada, M. Shiomi, K. Uematsu, and M. Matsumoto: J. Mater. Process. Technol., 2001, vol. 111, pp. 210–13.10.1016/S0924-0136(01)00522-2 ↗
8. Z. Lijing, L. Yingying, S. Shaobo, and Z. Hu: Chin. J. Aeronaut., 2015, vol. 28, pp. 564–69.10.1016/j.cja.2015.01.013 ↗
9. D. Gu, Y.C. Hagedorn, W. Meiners, G. Meng, R.J.S. Batista, K. Wissenbach, and R. Poprawe: Acta Mater., 2012, vol. 60, pp. 3849–60.10.1016/j.actamat.2012.04.006 ↗
10. M. Simonelli, Y.Y. Tse, and C. Tuck: Annual International Solid Freeform Fabrication Symposium, University of Texas, Austin, TX, 2012.
11. R.A. Wood: Titanium Alloy Handbook, Metals and Ceramics Information Center, Battelle, Columbus, OH, Dec 1972, publication no. MCIC-HB-02.
12. J.P. Blanchard, A. Chen, and B. Qiu: Nucl. Instrum. Meth. B, 1993, vol. 82, pp. 63–68.10.1016/0168-583X(93)95083-H ↗
13. M.K. Mcquillan: J. Metall. Rev., 1963, vol. 8, pp. 41–104.
14. M. Niinomi: Mater. Sci. Eng. A, 1998, vol. 243, pp. 231–36.10.1016/S0921-5093(97)00806-X ↗
15. I. Gurrappa: Mater. Charact., 2003, vol. 51, pp. 131–39.10.1016/j.matchar.2003.10.006 ↗
16. F.H. Froes, H. Friedrich, J. Kiese, and D. Bergoint: JOM, 2004, vol. 56, pp. 40–44.10.1007/s11837-004-0144-0 ↗
17. Q. Huang, X. Liu, X. Yang, R. Zhang, Z. Shen, and Q. Feng: Front. Mater. Sci., 2015, vol. 9, 373–81.10.1007/s11706-015-0315-7 ↗
18. B. Vrancken, L. Thijs, J.P. Kruth, and J.V. Humbeeck: J. Alloy Compd., 2012, vol. 541, 177–85.10.1016/j.jallcom.2012.07.022 ↗
19. G.M.T. Haar and T.H. Becker: Materials, 2018, vol. 11(1), p. 146.10.3390/ma11010146 ↗
20. H.K. Rafi, T.L. Starr, and B.E. Stucker: Int. J. Adv. Manuf. Technol., 2013, vol. 69, 1299–1309.10.1007/s00170-013-5106-7 ↗
21. T. Vilaro, C. Colin, and J.D. Bartout: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 3190–99.10.1007/s11661-011-0731-y ↗
22. S. Leuders, M. Thone, A. Riemer, T. Niendorf, T. Troster, H.A. Richard, and H.J. Maier: Int. J. Fatigue, 2013, vol. 48, pp. 300–07.10.1016/j.ijfatigue.2012.11.011 ↗
23. Y.K. Kim, S.H. Park, J.H. Yu, B. AlMangour, and K.A. Lee: Mater. Sci. Eng. A, 2018, vol. 715, pp. 33–40.10.1016/j.msea.2017.12.085 ↗
24. B. Baufeld, O.V.D. Biest, and R. Gault: Mater. Des., 2010, vol. 31, pp. S106–S111.10.1016/j.matdes.2009.11.032 ↗
25. S.L. Campanelli, N. Contuzzi, A.D. Ludovico, F. Caiazzo, F. Cardaropoli, and V. Sergi: Materials, 2014, vol. 7, pp. 4803–22.10.3390/ma7064803 ↗
26. T. Becker, M.V. Rooyen, and D. Dimitrov: S. Afr. J. Ind. Eng., 2015, vol. 26, pp. 93–103.
27. M. Simonelli, Y.Y. Tse, and C. Tuck: Metall. Mater. Trans. A, 2014, vol. 45A, 2863–72.10.1007/s11661-014-2218-0 ↗
28. T.J. Ruggles, T.M. Rampton, A. Khosravani, and D.T. Fullwood: Ultramicroscopy, 2016, vol. 164, pp. 1–10.10.1016/j.ultramic.2016.03.003 ↗
29. M. Calcagnotto, D. Ponge, E. Demir, and D. Raabe: Mater. Sci. Eng. A, 2010, vol. 527, pp. 2738–46.10.1016/j.msea.2010.01.004 ↗
30. S.H. Joo, H. Kato, M.J. Jang, J. Moon, C.W. Tsai, J.W. Yeh, and H.S. Kim: Mater. Sci. Eng. A, 2017, vol. 689, pp. 122–33.10.1016/j.msea.2017.02.043 ↗
31. L. Thijs, F. Verhaeghe, T. Craeghs, J.V. Humbeeck, and J.P. Kruth: Acta Mater., 2010, vol. 58, pp. 3303–12.10.1016/j.actamat.2010.02.004 ↗
32. L.E. Murr, E.V. Esquivel, S.A. Quniones, S.M. Gaytan, M.I. Lopez, E.Y. Martinez, F. Medina, D.H. Hernadez, E. Martinez, J.L. Martinez, S.W. Stafford, D.K. Brown, T. Hoppe, W. Meyers, U. Lindhe, and R.B. Wicker: Mater. Charact., 2009, vol. 60, pp. 96–105.10.1016/j.matchar.2008.07.006 ↗
33. B. Vandenbroucke and J.P. Kruth: Rapid Prototyp. J., 2007, vol. 13, pp. 193–203.10.1108/13552540710776142 ↗
34. L. Facchini, E. Magalini, P. Robotti, A. Molinari, S. Hoges, and K. Wissenbach: Rap. Prototyp. J., 2010, vol. 16, pp. 450–59.10.1108/13552541011083371 ↗
35. M. Vanderhasten, L. Rabet, and B. Verlinden: Metalurgija, 2005, vol. 11, pp. 195–200.
36. J.A. Hines and K.S. Vecchio: Acta Mater., 1997, vol. 45, pp. 635–49.10.1016/S1359-6454(96)00193-0 ↗