Investigation of the Microstructural, Mechanical and Corrosion Properties of Grade A Ship Steel-Duplex Stainless Steel Composites Produced via Explosive Welding
Source abstract
Abstract
Grade A ship-building steel-AISI 2304 duplex stainless steel composite plates were manufactured via explosive welding. The AISI 2304 plates were used to clad the Grade A plates. Optical microscopy studies were conducted on the joining interface for characterization of the manufactured composite plates. Notch impact, tensile-shear, microhardness, bending and twisting tests were carried out to determine the mechanical properties of the composites. In addition, the surfaces of fractured samples were examined by scanning electron microscopy (SEM), and neutral salt spray (NSS) and potentiodynamic polarization tests were performed to examine corrosion behavior. Near the explosion zone, the interface was completely flat, but became wavy as the distance from the explosion zone increased. The notch impact tests indicated that the impact strength of the composites decreased with increasing distance from the explosion zone. The SEM studies detected brittle behavior below the impact transition temperature and ductile behavior above this temperature. Microhardness tests revealed that the hardness values increased with increasing distance from the explosion zone and mechanical tests showed that no visible cracking or separation had occurred on the joining interface. The NSS and potentiodynamic polarization tests determined that the AISI 2304 exhibited higher corrosion resistance than the Grade A steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. M. Kwiecien, J. Majta and D. Dziedzic: Arch. Civil. Mech. Eng, 2014, vol. 14, pp. 32-9.10.1016/j.acme.2013.07.003 ↗
2. R. Ma, Y. Wang, J. Wu and M. Duan: Fusion. Eng. Design, 2014, vol. 89, pp. 3117-24.10.1016/j.fusengdes.2014.10.001 ↗
3. T.N. Prasanthi, C. SudhaRavikirana, S. Saroja: Mater. Design, 2016, vol. 93, pp. 180-193.10.1016/j.matdes.2015.12.120 ↗
4. M. Gloc, M. Wachowski, T. Plocinski, K. JanKurzydlowski: J. Alloys Compd., 2016, vol. 671, pp. 446-451.10.1016/j.jallcom.2016.02.120 ↗
5. L. Tricarico and R. Spina: Mater. Design, 2010, vol. 31, pp. 1981-92.10.1016/j.matdes.2009.10.032 ↗
6. X. Guo, H. Wang, Z. Liu, L. Wang, F. Ma and J. Tao: Int. J. Adv. Manuf. Technol, 2016, vol. 82, pp. 543-8.10.1007/s00170-015-7380-z ↗
7. I. Samardzic, B. Matesa and I. Kladaric: Metalurgija, 2011, vol. 50(3), pp. 159-62.
8. V. N. Arisova, Y. P. Trykov, I. A. Ponomareva, E. V. Miroshnikova (2014) Rus. J. Non-Ferrous Metals 55(1): 46-50.10.3103/S1067821214010027 ↗
9. H. Amani and M. Soltanieh: Metallurgical Mater. Transac. B, 2016, vol. 47(4), pp. 2524-34.10.1007/s11663-016-0682-1 ↗
10. J.Z. Ashani and S.M. Bagheri: Mater. Werkst. 2009, vol .40, pp. 690-8.10.1002/mawe.200900415 ↗
11. D. M. Fronczek, J. Wojewoda-Budka, R. Chulist, A. Sypien A. Korneva, Z. Szulc, N. Schell, P. Zieba (2016) Mater. Design 91:80-89.10.1016/j.matdes.2015.11.087 ↗
12. N. Kahraman, B. Gülenç and F. Fındık: Int. J. Imp. Eng, 2007, vol. 34, pp. 1423-32.10.1016/j.ijimpeng.2006.08.003 ↗
13. N. Kahraman and B. Gülenç: J. Mater. Process. Tech, 2005, vol. 169, pp. 67-71.10.1016/j.jmatprotec.2005.02.264 ↗
14. R. Kaçar and M. Acarer: J. Mater. Process. Tech, 2004, vol. 152, pp. 91-6.10.1016/j.jmatprotec.2004.03.012 ↗
15. W. Jiang, Y. Luo, G. Zhang, W. Woo and S.T. Tu: Mater. Design, 2013, vol. 51, pp. 1052-9.10.1016/j.matdes.2013.05.027 ↗
16. L.J. Zhang, Q. Pei, J.X. Zhang, Z.Y. Bi and P.C. Li: Mater. Design, 2014, vol. 64, pp. 462-76.10.1016/j.matdes.2014.08.013 ↗
17. R. Kaçar and M. Acarer: Mater. Sci. Eng. A, 2003, vol. 363, pp. 290-6.10.1016/S0921-5093(03)00643-9 ↗
18. Y. Kaya and N. Kahraman: Mater. Design, 2013, vol. 52, pp. 367-72.10.1016/j.matdes.2013.05.033 ↗
19. M. Prazmowski, D. Rozumek and H. Paul: Eng. Failure Analysis, 2017, vol. 75, pp 71-81.10.1016/j.engfailanal.2016.12.022 ↗
20. Q. Chu, M. Zhang, J. Li and C. Yan: Mater. Sci. Eng. A, 2017, vol. 689, pp 323-31.10.1016/j.msea.2017.02.075 ↗
21. B. Wang, F. Xie, X. Luo, J. Zhou (2016) J. Mater. Res. Tech, 5(4):333-338.10.1016/j.jmrt.2016.04.001 ↗
22. B. Gülenç, Y. Kaya, A. Durgutlu, İ.T. Gülenç, M.S. Yıldırım and N. Kahraman: Arch. Civil. Mech. Eng, 2016, vol. 16, pp. 1-8.10.1016/j.acme.2015.09.006 ↗
23. S. Belyaev, V. Rubanik, N. Resnina, V. Rubanik Jr., E. Demidova and I. Lomakin: J. Mater. Process. Tech, 2016, vol. 234, pp. 323-31.10.1016/j.jmatprotec.2016.04.004 ↗
24. D. V. Lazurenko, I. A. Bataev, V. I. Mali, A. A. Bataev, I. N. Maliutina, V. S. Lozhkin, M. A. Esikov, A. M. J. Jorge (2016) Mater. Design 102:122-130.10.1016/j.matdes.2016.04.037 ↗
25. G. Miao, H. Ma, Z. Shen and Y. Yu: Mater. Design, 2014, vol. 63, pp. 538-43.10.1016/j.matdes.2014.06.050 ↗
26. M. Acarer, B. Gülenç and F. Fındık: J. Mater. Sci. 2004, vol. 39(21), pp. 6457-66.10.1023/B:JMSC.0000044883.33007.20 ↗
27. M. Acarer, B. Gülenç and F. Fındık: Mater. Design, 2003, vol. 24, pp. 659-64.10.1016/S0261-3069(03)00066-9 ↗
28. A.A. Akbari Mousavi and S.T.S. Al-Hassani: J. Mech. Phys. Solids, 2005, vol. 53, pp. 2501-28.10.1016/j.jmps.2005.06.001 ↗
29. Y. Kaya: Ph D Thesis, Karabük University, TR, 2014, pp. 1–215.
30. W.F. Smith: Structure and Properties of Engineering alloys. 2 nd ed., McGraw-Hill, Inc., New York: 1981.
31. N. Kahraman, B. Gülenç and F. Fındık: J. Mater. Process. Tech, 2005, vol. 169, pp. 127-33.10.1016/j.jmatprotec.2005.06.045 ↗
32. M. Asemabadi, M. Sedighi and M. Honarpisheh: Mater. Sci. Eng. A, 2012, vol. 558, pp. 144-9.10.1016/j.msea.2012.07.102 ↗
33. M.H. Bina, F. Dehghani and M. Salimi: Mater. Design, 2013, vol. 45, pp. 504-9.10.1016/j.matdes.2012.09.037 ↗
34. M. Yazdani, T.R. Toroghinejad and S.M. Hashemi: J. Mater. Eng. Perf, 2015, vol. 24, pp. 4032-43.10.1007/s11665-015-1670-3 ↗
35. M.M.H. Athar and B. Tolaminejad: Mater. Design, 2015, vol. 86, pp. 516-25.10.1016/j.matdes.2015.07.114 ↗
36. H.B. Xia, S.G. Wang and H.F. Ben: Mater. Design, 2014, vol. 56, pp. 1014-9.10.1016/j.matdes.2013.12.012 ↗
37. X. Guo, J. Tao, W. Wang, H. Li and C. Wang: Mater. Design, 2013, vol. 49, pp. 116-22.10.1016/j.matdes.2013.02.001 ↗
38. Y. Wang, H.G. Beom, M. Sun and S. Lin: Int. J. Imp. Eng, 2011, vol. 38, pp. 51-60.10.1016/j.ijimpeng.2010.08.003 ↗
39. T. Mooney, 2003. ASM Handbook, Volume 13A-Corrosion: Fundamentals, Testing, and Protection. ASM International: New York
40. M. Acarer (2012) J. Mater. Eng. Perf 21(11):2375-2379.10.1007/s11665-012-0203-6 ↗