journal article·2016-07

Experimental Measurements for Numerical Simulation of Macrosegregation in a 36-Ton Steel Ingot

Zhenhu Duan, Wutao Tu, Bingzhen Shen, Houfa Shen, Baicheng Liu

Publisher page

Abstract

In order to cognize the macrosegregation formation with solidification conditions, a 36-ton steel ingot has been experimentally investigated. Temperature variations of fourteen specified positions, for both the mold and ingot, were monitored to acquire the thermal conditions during solidification. Calibrated heat transfer coefficients between the ingot and mold were determined based on the temperature measurements and the empirical formula. Besides, concentration distributions of both carbon and sulfur in the ingot longitudinal section were mapped by 1800 drilled samples. Macrosegregation patterns were obtained, and notable negative segregations along the side walls of hot-top as well as typical segregation characteristics were presented in the maps. Segregation extent of sulfur was greater than that of carbon, and the segregated sulfur was relevant to the segregated carbon in a certain extent on statistical analysis with a standard correlation coefficient r = 0.68872. Finally, a two-phase multiscale multicomponent solidification model was preliminarily utilized to predict the species segregation. General good agreements are exhibited for the comparisons between the prediction and measurement of concentration profiles of carbon and sulfur in ingot.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Solidification and crystal growth phenomena · Metallurgical Processes and Thermodynamics · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. C. Beckermann: Int. Mater. Rev., 2002, vol. 47, pp. 243-61.10.1179/095066002225006557 ↗
2. E. J. Pickering: ISIJ Int., 2013, vol. 53, pp. 935-949.10.2355/isijinternational.53.935 ↗
3. D. Z. Li, X. Q. Chen, P. X. Fu, X. P. Ma, H. W. Liu, Y. Chen, Y. F. Cao, Y. K. Luan, and Y. Y. Li: Nat. Commun., 2014, vol. 5, pp.5572. doi:10.1038/ncomms6572.10.1038/ncomms6572 ↗
4. M. C. Flemings and G. E. Nereo: Trans. Metall. Soc. AIME, 1967, vol. 239, pp. 1449-61.
5. W. D. Bennon and F. P. Incropera: Int. J. Heat Mass Transfer, 1987, vol. 30, pp. 2161-70.10.1016/0017-9310(87)90094-9 ↗
6. C. Beckermann and R. Viskanta: Physicochem. Hydrodyn., 1995, vol. 10, pp. 195-213.
7. J. Ni and C. Beckermann: Metall. Trans. B, 1991, vol. 22B, pp. 349-61.10.1007/BF02651234 ↗
8. C. Y. Wang and C. Beckermann: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2754-64.10.1007/BF02652369 ↗
9. M. Wu and A. Ludwig: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1613-31.10.1007/s11661-006-0104-0 ↗
10. M. Bellet, H. Combeau, Y. Fautrelle, D. Gobin, M. Rady, E. Arquis, O. Budenkova, B. Dussoubs, Y. Duterrail, A. Kumar, C. A. Gandin, B. Goyeau, S. Mosbah, and M. Založnik: Int. J. Therm. Sci., 2009, vol. 48, pp. 2013–16.10.1016/j.ijthermalsci.2009.07.024 ↗
11. G. Lesoult: Mater. Sci. Eng. A, 2005, vols. 413-414A, pp. 19–29.10.1016/j.msea.2005.08.203 ↗
12. J. Li, M. Wu, A. Ludwig, and A. Kharicha: Int. J. Heat Mass Transfer, 2014, vol. 72, pp. 668–79.10.1016/j.ijheatmasstransfer.2013.08.079 ↗
13. S. Hans, P.E. Richy, B. Lusson, and A. Grellier: in 1st Multidisciplinary Congress on Materials, Tours, France, 2002, AF16005.
14. H. Combeau, B. Rabia, S. Charmond, S. Hans, and P.E. Richy: in 2nd Multidisciplinary Conference on Materials, Dijon, France, 2006.
15. H. Combeau, M. Založnik, S. Hans, and P. E. Richy: Metall. Mater. Trans. B, 2009, vol. 40B, pp. 289–304.10.1007/s11663-008-9178-y ↗
16. J.Pickering, C.Chhesman, S.Al-Bermani, M. Holland, P.Davies, and J. Talamantes-silva: Metall. Mater. Trans. B, 2015, vol.46B, pp.1860-1874.10.1007/s11663-015-0386-y ↗
17. P. Machovcak, A. Opler, Z. Carbol, A. Trefil, K. Merta, J. Zaoral, M. Tkadleckova, and K. Michalek: Arch. Mater. Sci. Eng., 2012, vol. 58, pp. 22–27.
18. K. Kajikawa, S. Suzuki, F. Takahashi, S. Yamamoto, T. Suzuki, S. Ueda, T. Shibata, and H. Yoshida: in 1st International Conference on Ingot Casting, Rolling and Forging, Aachen, Germany, 2012.
19. W. S. Li, H. F. Shen, X. Zhang and B. C. Liu: Metal. Mater. Trans. B, 2014, vol. 45B, pp. 464–71.10.1007/s11663-013-9862-4 ↗
20. W. Tu, H. Shen, and B. Liu: ISIJ Int., 2014, vol. 54, pp. 351–55.10.2355/isijinternational.54.351 ↗
21. Z. Duan, H. Shen, and B. Liu: in The 14th Modelling of Casting, Welding and Advanced Solidification Process, Hyogo, Japan, 2015, p. 012048.
22. M. C. Schneider and C. Beckermann: Metal. Mater. Trans. A, 1995, vol. 9A, pp. 2373–88.10.1007/BF02671251 ↗
23. ProCAST software, version 2011, https://www.esi-group.com/software-services/virtual-manufacturing/casting/procast-quikcast.
24. W.S. Li, B.Z. Shen, H.F. Shen, and B.C. Liu: in The 69th World Foundry Congress, Hangzhou, P.R. China, 2010, pp. 0537–40.
25. Z. Liu, Y. Zhao, Y. Zhang, H. L. Zhao, Y. T. Yang: J. Iron.Steel.Res, 1993, vol.5, pp. 23-32.