Effect of Natural Aging and Cold Working on Microstructures and Mechanical Properties of Al-4.6Cu-0.5Mg-0.5Ag alloy
Source abstract
Abstract
This research investigates the effects of natural aging and cold working prior to artificial aging on microstructures and mechanical properties of Al-4.6Cu-0.5Mg-0.5Ag alloy. Mechanical properties relative to microstructure variations were elucidated by the observations of the optical microscope (OM), differential scanning calorimeter (DSC), electrical conductivity meter (pct IACS), and transmission electron microscopy (TEM). The results showed that natural aging treatment has little noticeable benefit on the quantity of precipitation strengthening phases and mechanical properties, but it increases the precipitation strengthening rate at the initial stage of artificial aging. Cold working brings more lattice defects which suppress Al-Cu (GP zone) and Mg-Ag clustering, and therefore the precipitation of Ω phase decreases. Furthermore, more dislocations are formed, leading to precipitate the more heterogeneous nucleation of θ′ phase. The above-mentioned precipitation phenomena and strain hardening effect are more obvious with higher degrees of cold working.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. I. J. Polmear, G. Pons, Y. Barbaux, H. Octor, C. Sanchez, A. J. Morton, W. E. Borbidge, S. Roger:Mater. Sci. Tech., 1999, vol. 15, pp. 861–68.10.1179/026708399101506599 ↗
2. I. J. Polmear, M. J. Couper: Metall. Trans. A, 1988, vol. 19A, pp. 1027–35.10.1007/BF02628387 ↗
3. B. C. Muddle, I. J. Polmear: Acta Metall. Mater., 1989, vol. 37, pp. 777–89.10.1016/0001-6160(89)90005-9 ↗
4. K. Hono, N. Sano, S. S. Babu, R. Okano, T. Sakurai: Acta metall. mater., 1993, vol. 41, pp. 829-838.10.1016/0956-7151(93)90016-L ↗
5. A. Grag, Y. C. Chang and J.M. Howe: Scripta Mater., 1990, vol. 24, pp. 677-680.10.1016/0956-716X(90)90222-3 ↗
6. C-H Chang, S-L Lee, T-Y Hsu, J-C Lin: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 2832-2340.10.1007/s11661-007-9332-1 ↗
7. K.M. Knowles and W.M. Stobbs: Acta Crystallogr., 1988, vol. B44, pp. 207–27.10.1107/S0108768187012308 ↗
8. A. K. Mukhopadhyay: Mater. T. JIM. 1997, vol. 38, pp. 478-482.10.2320/matertrans1989.38.478 ↗
9. K. Hono, T. Sakurai, I. J. Polmear: Scripta Metall. Mater., 1994, vol. 30, pp. 695-700.10.1016/0956-716X(94)90184-8 ↗
10. Y-J Zhuang, S-L Lee: J. Taiwan foundry soc., 2003, vol. 116, pp. 35-42.
11. S. P. Ringer, B. C. Muddle and I. J. Polmear: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1659-1671.10.1007/BF02670753 ↗
12. Q. Li and R.N. Shenoy: J. Mater. Sci., 1997, vol. 32, pp. 3401–06.10.1023/A:1018664515422 ↗
13. ASTM B597-83, Annual Book of ASTM Standards, Vol.02.02, 1984.
14. ASTM B557M-81, Annual Book of ASTM Standards, Vol.03.01, 1991.
15. A. K. Mukhopadhyay and V. V. Rama Rao: Mater. Sci. Eng. A, 1999, vol. A268, pp. 8-14.10.1016/S0921-5093(99)00123-9 ↗
16. A. K. Mukhopadhyay: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1693-1704.10.1007/s11661-999-0169-7 ↗
17. C-H Chang, S-L Lee: Mater. Trans., JIM, 2005, vol. 46, No. 2. pp. 236-240.10.2320/matertrans.46.236 ↗
18. S. Abis, P. Mengucci and G. Riontino: Philos. Mag. B, 1993, vol. B67, pp. 465-484.10.1080/13642819308207686 ↗
19. C-T. Wu, S-L. Lee, M-H. Heieh, J-C. Lin: Metall. Mater. Trans. A, 2010, vol. 41A. pp. 751-757.10.1007/s11661-009-0133-6 ↗
20. O. Beffort, C. Solenthaler, M. O. Speidel: Mater. Sci. Eng. A, 1995, vol. A191, pp. 121–34.10.1016/0921-5093(94)09642-2 ↗