journal article·2005-03Open access

Mechanical properties and fracture behavior of an ultrafine-grained Al-20 wt pct Si alloy

Soon-Jik Hong, C. Suryanarayana

Abstract

The effect of powder particle size on the microstructure, mechanical properties, and fracture behavior of Al-20 wt pct Si alloy powders was studied in both the gas-atomized and extruded conditions. The microstructure of the as-atomized powders consisted of fine Si particles and that of the extruded bars showed a homogeneous distribution of fine eutectic Si and primary Si particles embedded in the Al matrix. The grain size of fcc-Al varied from 150 to 600 nm and the size of the eutectic Si and primary Si was about 100 to 200 nm in the extruded bars. The room-temperature tensile strength of the alloy with a powder size <26 μm was 322 MPa, while for the coarser powder (45 to 106 μm), it was 230 MPa. The tensile strength of the extruded bar from the fine powder (<26 μm) was also higher than that of the Al-20 wt pct Si-3 wt pet Fe (powder size: 60 to 120 μm) alloys. With decreasing powder size from 45 to 106 μm to <26 μm, the specific wear of all the alloys decreased significantly at all sliding speeds due to the higher strength achieved by ultrafine-grained constituent phases. The thickness of the deformed layer of the alloy from the coarse powder (10 μm at 3.5 m/s) was larger on the worm surface in comparison to the bars from the fine powders (5 μm at 3.5 m/s), attributed to the lower strength of the bars with coarse powders.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. H. Yoon, T. Sheiretov, and C. Cusano: Wear, 2000, vol. 237, pp. 163–75.10.1016/S0043-1648(99)00321-X ↗
2. A. Kaye and A. Street: Die Casting Metallurgy, Butterworth and Co., London, 1982, p. 32.
3. S. Anand, T.S. Srivatsan, T. Wu, and E.J. Lavernia: J. Mater. Sci. 1997, vol. 32, pp. 2835–48.10.1023/A:1018668332318 ↗
4. M.D. Hanna, S. Lu, and A. Hellawell: Metall. Trans. A, 1984, vol. 15A, pp. 459–69.10.1007/BF02644969 ↗
5. F. Yilmaz and R. Elliott: J. Mater. Sci., 1989, vol. 24, pp. 2065–70.10.1007/BF02385422 ↗
6. A. Knuutinen, K. Nogita, S.D. McDonald, and A.K. Dahle: J. Light Met., 2001, vol. 1, pp. 229–40.10.1016/S1471-5317(02)00004-4 ↗
7. J. Zhou, J. Duszczyk, and B.M. Korevaar: J. Mater. Sci., 1991, vol.
8. S.J. Hong, T.S. Kim, W.T. Kim, and B.S. Chun: Mater. Sci. Eng., 1997, vols. A226–A228, pp. 878–82.10.1016/S0921-5093(96)10811-X ↗
9. X.G. Zou, H. Miyahara, K. Yamamoto, and K. Ogi: Mater. Sci. Technol., 2003, vol. 19, pp. 1519–26.10.1179/026708303225007997 ↗
10. X.G. Zou, H. Miyahara, K. Yamamoto, and K. Ogi: Mater. Sci. Technol., 2003, vol. 19, pp. 1527–30.10.1179/026708303225006015 ↗
11. A. Inoue, K. Ohtera, A.P. Tsai, and T. Masumoto: Jpn. J. Appl. Phys., 1988, vol. 27, p. 280.10.1143/JJAP.27.L280 ↗
12. Y.H. Kim, A. Inoue, and T. Masumoto: Mater. Trans. JIM, 1991, vol. 32, p. 331.10.2320/matertrans1989.32.331 ↗
13. S.J. Hong, T.S. Kim, H.S. Kim, W.T. Kim, and B.S. Chun: Mater. Sci. Eng., 1999, vol. A271, pp. 469–76.10.1016/S0921-5093(99)00317-2 ↗
14. H.H. Liebermann, ed.: Rapidly Solidified Alloys: Processes, Structures, Properties, Applications, Marcel Dekker, New York, NY, 1993.
15. T.R. Anantharaman and C. Suryanarayana: Rapidly Solidified Metals: A Technological Overview, Trans Tech Publication, Aedermannsdorf, Switzerland, 1987.10.4028/b-uPTE08 ↗
16. H. Jones: in Non-Equilibrium Processing of Materials, C. Suryanarayana, ed., Pergamon Press, Oxford, United Kingdom, 1999, pp. 23–45.10.1016/S1470-1804(99)80049-2 ↗
17. T. Hayashi, T. Kaji, Y. Takeda, Y. Odani, and K. Akechi: Sumitomo Electric Tech. Rev., 1992, vol. 34, p. 107.
18. T.S. Kim, S.J. Hong, W.T. Kim, C.W. Won, S.S. Cho, and B.S. Chun: Mater. Trans. JIM, 1998, vol. 39, pp. 1214–19.10.2320/matertrans1989.39.1214 ↗
19. J. Zhou, J. Duszczyk, and B.M. Korevaar: J. Mater. Sci., 1991, vol. 26, pp. 824–34.10.1007/BF00588323 ↗
20. T.S. Kim, C. Suryanarayana, and B.S. Chun: Mater. Sci. Eng., 2000, vol. A278, pp. 113–20.10.1016/S0921-5093(99)00589-4 ↗
21. A. Inoue: Progr. Mater. Sci., 1998, vol. 43, pp. 365–520.10.1016/S0079-6425(98)00005-X ↗
22. Amorphous and Nanocrystalline Materials, A. Inoue and K. Hashimoto, eds., Springer-Verlag, Berlin, 2001.
23. Y. Kawamura, H. Mano, and A. Inoue: Scripta Mater., 2001, vol. 44, pp. 1599–1604.10.1016/S1359-6462(01)00781-3 ↗
24. S.J. Hong, H.S. Kim, C. Suryanarayana, and B.S. Chun: Mater. Sci. Technol., 2003, vol. 19, pp. 966–72.10.1179/026708303225003036 ↗
25. N. Amano, Y. Ohtani, Y. Takeda, and K. Ajech: Metal Powder Rep., 1983, vol. 38, p. 186.
26. L.A. Davis, S.K. Das, J.C.M. Li, and M.S. Zedalis: Int. J. Rapid Solidification, 1994, vol. 8, pp. 73–131.
27. V.K. Kanth, B.N.P. Bai, and S.K. Biswas: Scripta Metall. Mater., 1990, vol. 24, pp. 267–71.10.1016/0956-716X(90)90254-E ↗
28. B. Venkataraman and G. Sundararajan: Acta Metall., 1996, vol. 44, pp. 451–60.