Microstructural Changes During Plastic Deformation and Corrosion Properties of Biomedical Co-20Cr-15W-10Ni Alloy Heat-Treated at 873 K
Source abstract
Abstract
Microstructural changes were observed during the plastic deformation of ASTM F90 Co-20Cr-15W-10Ni (mass pct) alloy heat-treated at 873 K (600 °C) for 14.4 ks, and analyzed by electron backscatter diffraction and in situ X-ray diffraction techniques. The obtained results revealed that the area fraction of the e-phase (fe) in the as-received alloy was higher than that in the heat-treated alloy in the low-to-middle strain region (≤ 50 pct), whereas the fe of the heat-treated alloy was higher than that of the as-received alloy at the fracture point. During plastic deformation, the e-phase was preferentially formed at the twin boundaries of the heat-treated alloy rather than at the grain boundaries. According to the transmission electron microscopy observations, the thin e-phase layer formed due to the alloy heat treatment acted as the origin of deformation twinning, which decreased the stress concentration at the grain boundaries. The results of anodic polarization testing showed that neither the heat treatment at 873 K (600 °C) nor plastic deformation affected the alloy corrosion properties. To the best of our knowledge, this is the first study proving that the formation of a thin e-phase layer during the low-temperature heat treatment of the studied alloy represents an effective method for the enhancement of the alloy ductility without sacrificing its strength and corrosion properties.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Titanium Alloys Microstructure and Properties · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. J. Favre, Y. Koizumi, A. Chiba, D. Fabregue and E. Maire: Metall. Mater. Trans. A, 2013, vol. 44, pp. 2819–2830.10.1007/s11661-012-1602-x ↗
2. P. Poncin and J. Proft: Med. Device Mater., Proc. Mater. Process. Med. Devices Conf., 2003, pp. 253–59.
3. F.R. Morral: J. Mater., 1966, vol. 1, pp. 384–412.
4. R.V. Marrey, R. Butgermeister, R. B. Grishaber and R. O. Ritchie: Biomaterials, 2006, vol. 27, pp. 1988–2000.10.1016/j.biomaterials.2005.10.012 ↗
5. K. Ueki, K. Ueda and T. Narushima: Metall. Mater. Trans. A, 2016, vol. 47, pp. 2773–2782.10.1007/s11661-016-3488-5 ↗
6. T. Narushima, S. Mineta, Y. Kurihara and K. Ueda: JOM 2013 vol. 65, pp. 489–504.10.1007/s11837-013-0567-6 ↗
7. Y. Koizumi, S. Suzuki, K. Yamanaka, B-S. Lee, K. Sato, Y. Li, S. Kurosu, H. Matsumoto and A. Chiba: Acta Mater., 2013, vol. 61, pp. 1648–1661.10.1016/j.actamat.2012.11.041 ↗
8. K. Yamanaka, M. Mori, S. Kurosu, H. Matsumoto and A. Chiba: Metall. Mater. Trans. A, 2009, vol. 40, pp. 1980–1994.10.1007/s11661-009-9879-0 ↗
9. K. Yamanaka, M. Mori and A. Chiba: Metall. Mater. Trans. A, 2012, vol. 43, pp. 4875–4887.10.1007/s11661-012-1303-5 ↗
10. K Yamanaka, M. Mori and A. Chiba: Acta Biomater., 2013, vol. 9, pp. 6259–6267.10.1016/j.actbio.2012.12.013 ↗
11. S. Kurosu, H. Matsumoto, A. Chiba, C. Landron, D. Fabregue and E. Maire: Scr. Mater., 2011, Vol. 64, pp 367–370.10.1016/j.scriptamat.2010.07.032 ↗
12. K. Hagihara, T. Nakano and K. Sasaki: Scr. Mater. 2016. Vol. 123, pp 149–153.10.1016/j.scriptamat.2016.06.016 ↗
13. J. Teague, E. Cerreta and M. Stout: Metall. Mater. Trans. A, 2004, vol. 35, pp. 2767–2781.10.1007/s11661-004-0223-4 ↗
14. R. K. Gupta, M. K. Karthikeyan, D. N. Bhalia, B. R. Ghosh and P. P. Sinha: Met. Sci. Heat Treat., 2008, vol. 50, pp. 175–178.10.1007/s11041-008-9031-6 ↗
15. N. Yukawa and K. Sato: Mater. Trans. JIM, 1968, vol. 9, pp. 680–686.
16. M. Tanaka and H. Iizuka: Metall. Mater. Trans. A, 1992, vol. 23, pp. 609–616.10.1007/BF02801178 ↗
17. P. Poncin, B. Gruez, P. Missillier, and P. Comte-Gaz: Med. Device Mater. III, Proc. Mater. Process. Med. Devices Conf., 2006, pp. 85–90.
18. P. Poncin, C. Millet, and J. Chevy: Med. Device Mater. II, Proc. Mater. Process. Med. Devices Conf., 2nd, 2004, pp. 279–83.
19. W. Walke, Z. Paszenda and J. Tyrlik-Held: Journal of Achievements in Materials and Manufacturing Engineering, 2006, vol. 16, pp.74–79.
20. S. Mineta, Alfirano, S. Namba, T. Yoneda, K. Ueda and T. Narushima: Metall. Mater. Trans. A, 2012, vol. 43, pp. 3351–3358.10.1007/s11661-012-1142-4 ↗
21. S. Mineta, S. Namba, T. Yoneda, T. Ueda and T. Narushima: Metall. Mater. Trans. A, 2010, vol. 41, pp. 2129–2138.10.1007/s11661-010-0227-1 ↗
22. D. T. Sawyer, A. J. Sobkowiak and J. L. Roberts, Jr.: Electrochemistry for Chemists, 2nd ed., John Wiley & Sons, New York, NY, 1995, pp 192.
23. S. Hiromoto, E.Onodera, A. Chiba, K. Asami and T. Hanawa: Biomaterials, 2005 vol. 26, pp. 4912–4923.10.1016/j.biomaterials.2005.01.028 ↗
24. H. M. Tawancy, V. R. Ishwar and B. E. Lewis: J. Mater. Sci. Lett., 1986, vol. 5, pp. 337–341.10.1007/BF01748098 ↗
25. H. Fujita and T. Mori: Scr. Metall., 1975, Vol. 9, pp. 631–636.10.1016/0036-9748(75)90476-7 ↗
26. C. Montero-Ocampo, R. Juarez and A. Salinas Rodriguez: Metall. Mater. Trans. A, 2002, vol. 33, pp. 2229–2235.10.1007/s11661-002-0054-0 ↗
27. M. Michiuchi, H. Kokawa, Z.J. Wang, Y.S. Sato, K. Sakai: Acta Mater., 2006, vol. 54, pp. 5179–5184.10.1016/j.actamat.2006.06.030 ↗
28. A. Eghlimi, M. Shamanian, M. Eskandarian, A. Zabolian and J. A. Szpunar: Mater. Charact., 2015, vol. 106, pp. 27–35.10.1016/j.matchar.2015.05.017 ↗
29. A. Eghlimi, M. Shamanian, M. Eskandarian, A. Zabolian, M. Nezakat and J. A. Szpunar: Surf. Coat. Tech., 2015, vol. 264, pp. 150-162.10.1016/j.surfcoat.2014.12.060 ↗