journal article·2018-01

Serrated Flow and Dynamic Strain Aging in Fe-Mn-C TWIP Steel

Peng Lan, Jiaquan Zhang

Publisher page

Abstract

The tensile behavior, serrated flow, and dynamic strain aging of Fe-(20 to 24)Mn-(0.4 to 0.6)C twinning-induced plasticity (TWIP) steel have been investigated. A mathematical approach to analyze the DSA and PLC band parameters has been developed. For Fe-(20 to 24)Mn-(0.4 to 0.6)C TWIP steel with a theoretical ordering index (TOI) between 0.1 and 0.3, DSA can occur at the very beginning of plastic deformation and provide serrations during work hardening, while for TOI less than 0.1 the occurrence of DSA is delayed and twinning-dominant work hardening remains relatively smooth. The critical strain for the onset of DSA and PLC bands in Fe-Mn-C TWIP steels decreases as C content increases, while the numbers of serrations and bands increase. As Mn content increases, the critical strain for DSA and PLC band varies irregularly, but the numbers of serrations and bands increase. For Fe-(20 to 24)Mn-(0.4 to 0.6)C TWIP steel with grain size of about 10 to 20 μm, the twinning-induced work hardening rate is about 2.5 to 3.0 GPa, while the DSA-dominant hardening rate is about 2.0 GPa on average. With increasing engineering strain from 0.01 to 0.55 at an applied strain rate of 0.001s−1, the cycle time for PLC bands in Fe-Mn-C TWIP steel increases from 6.5 to 162 seconds, while the band velocity decreases from 4.5 to 0.5 mm s−1, and the band strain increases from 0.005 to 0.08. Increasing applied strain rate leads to a linear increase of band velocity despite composition differences. In addition, the influence of the Mn and C content on the tensile properties of Fe-Mn-C TWIP steel has been also studied. As C content increases, the yield strength and tensile strength of Fe-Mn-C TWIP steel increase, but the total elongation variation against C content is dependent on Mn content. As Mn content increases, the yield strength and tensile strength decrease, while the total elongation increases, despite C content. Taking both tensile properties and serrated flow behavior into consideration, Fe-22Mn-0.4C TWIP steel shows excellent mechanical performance with a high product of tensile strength and total elongation and a slightly serrated stress–strain response. To suppress the negative effect of DSA in Fe-Mn-C TWIP steels on the stability of tensile behavior, a TOI lower than 0.1 is strongly suggested.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. S. Vercammen, B. Blanpain, B. C. De Cooman and P. Wollants: Acta Mater., 2004, vol. 52(7), pp. 2005-12.10.1016/j.actamat.2003.12.040 ↗
2. Y. Bai, Y. Momotani, M. C. Chen, A. Shibata and N. Tsuji: Mater. Sci. Eng. A, 2016, vol. 651, pp. 935-44.10.1016/j.msea.2015.11.017 ↗
3. J. Park, M. Kang, S. S. Sohn, S. H. Kim, H. S. Kim, N. J. Kim and S. Lee: Mater. Sci. Eng. A, 2017, vol. 684, pp. 54-63.10.1016/j.msea.2016.12.037 ↗
4. J. W. Cho, S. Yoo, M. S. Park, J. K. Park and K. H. Moon: Metall. Mater. Trans. B, 2017, vol. 48(1), pp. 187-96.10.1007/s11663-016-0818-3 ↗
5. J. K. Kim and B. C. De Cooman: Mater. Sci. Eng. A, 2016, vol. 676, pp. 216-31.10.1016/j.msea.2016.08.106 ↗
6. O. Grässel and G. Frommeyer: Mater. Sci. Technol., 1998, vol. 14(12), pp. 1213-17.10.1179/mst.1998.14.12.1213 ↗
7. O. Grässel, L. Krüger, G. Frommeyer and L.W. Meyer: Int. J. plast., 2000, vol. 16(10), pp. 1391-1409.10.1016/S0749-6419(00)00015-2 ↗
8. C. Scott, S. Allain, M. Faral and N. Guelton: Rev. Métall., 2006, vol. 103(6), pp. 293-302.10.1051/metal:2006142 ↗
9. S. Allain, J. P. Chateau, O. Bouaziz, S. Migot and N.Guelton: Mater. Sci. Eng. A, 2004, vol. 387, pp. 158-62.10.1016/j.msea.2004.01.059 ↗
10. L. Chen, H. S. Kim and S. K. Kim: ISIJ Int., 2007, vol. 47(12), pp. 1804-12.10.2355/isijinternational.47.1804 ↗
11. P. D. Zavattieri, V. Savic, L. G. Hector, J.R. Fekete, W. Tong and Y. Xuan: Int. J. Plast., 2009, vol. 25(12), pp. 2298-2330.10.1016/j.ijplas.2009.02.008 ↗
12. D. Barbier, N. Gey, S. Allain, N. Bozzolo and M. Humbert: Mater. Sci. Eng. A, 2009, vol. 500(1), pp. 196-206.10.1016/j.msea.2008.09.031 ↗
13. I. Gutierrez-Urrutia and D. Raabe: Acta Mater., 2011, vol. 59(16), pp. 6449-62.10.1016/j.actamat.2011.07.009 ↗
14. S. Allain, J. P. Chateau and O. Bouazi: Mater. Sci. Eng. A, 2004, vol. 387, pp.143-47.10.1016/j.msea.2004.01.060 ↗
15. O. Bouaziz, S. Allain and C. Scott: Scripta Mater., 2008, vol. 58(6), pp. 484-87.10.1016/j.scriptamat.2007.10.050 ↗
16. Y. N. Dastur and W. C. Leslie: Metall. Trans. A, 1981, vol. 12(5), pp.749-59.10.1007/BF02648339 ↗
17. S. Hong, S. Y. Shin, J. Lee, D.H. Ahn, H.S. Kim, S.K. Kim, K.G. Chin and S. Lee: Metall. Mater. Trans.A, 2014, vol. 45(2), pp. 633–46.10.1007/s11661-013-2007-1 ↗
18. S. J. Lee, J. Kim, S. N. Kane and B.C. De Cooman.: Acta Mater., 2011, vol. 59(17), pp. 6809-19.10.1016/j.actamat.2011.07.040 ↗
19. A. Saeed-Akbari, A. K. Mishra, J. Mayer and W. Bleck: Metall. Mater. Trans. A, 2012, vol. 43A(5), pp. 1705-23.10.1007/s11661-011-1070-8 ↗
20. V. Shterner, I. B. Timokhina and H. Beladi: Mater. Sci. Eng. A, 2016, vol.669, pp. 437-46.10.1016/j.msea.2016.05.104 ↗
21. K. Renard, S. Ryelandt and P. J. Jacques: Mater. Sci. Eng. A, 2010, vol. 527(12), pp. 2969-77.10.1016/j.msea.2010.01.037 ↗
22. M. Koyama, T. Sawaguchi, T. Lee, C.S. Lee and K. Tsuzaki: Mater. Sci. Eng. A, 2011, vol. 528(24), pp. 7310-16.10.1016/j.msea.2011.06.011 ↗
23. T. A. Lebedkina, M. A .Lebyodkin, J. P. Chateau, A. Jacques and S. Allain: Mater. Sci. Eng. A, 2009, vol. 519(1): 147-54.10.1016/j.msea.2009.04.067 ↗
24. J. K. Kim, L. Chen, H. S. Kim S.K. Kim, Y. Estrin and B.C. De Cooman: Metall. Mater. Trans. A, 2009, vol. 40A(13), pp. 3147-58.10.1007/s11661-009-9992-0 ↗
25. P. Lan and J. Zhang: Steel Res. Int., 2016, vol. 87(2), pp. 250-61.10.1002/srin.201500022 ↗
26. P. Lan, H. Tang and J. Zhang: Mater. Sci. Eng. A, 2016, vol. 660, pp. 127-38.10.1016/j.msea.2016.02.086 ↗
27. P. Lan, H. Tang and J. Zhang: Metall. Mater. Trans. A, 2016, vol. 47A(6), pp. 2964-84.10.1007/s11661-016-3445-3 ↗
28. P. Lan, L. Song, C. Du and J. Zhang: Mater. Sci. Technol., 2014, vol. 30(11), pp. 1297-1304.10.1179/1743284714Y.0000000560 ↗
29. P. Lan, C. Du, Y. Ji and J. Zhang: China Metall., 2014, vol. 24(7), pp. 6-16.
30. Y. Wang, P. Lan, Y. Li and J. Zhang: J. Mater. Eng., 2015, vol. 43(9), pp. 30-8.
31. P. Lan: Doctoral Thesis, University of Science and Technology Beijing, Beijing, 2015.
32. K. Yan, D. G. Carr, M. D. Callaghan, K.D. Liss and H. Li: Scripta Mater., 2010, vol. 262(5), pp. 246–9.10.1016/j.scriptamat.2009.11.008 ↗
33. J. A. Jiménez and G. Frommeyer: Mater. Charact., 2010, vol. 61(2), pp. 221-6.10.1016/j.matchar.2009.11.013 ↗
34. L. P. Kubin and Y. Estrin: Acta Metall. Mater., 1990, vol. 38(5), pp. 697-708.10.1016/0956-7151(90)90021-8 ↗
35. L. P. Kubin and Y. Estrin: J. Phys. III, 1991, vol. 1(6), pp. 929-43.
36. T.A. Lebedkina, M.A. Lebyodkin, J.P. Chateau, A. Jacques and S. Allain: Mater. Sci. Eng. A, 2009, vol. 519(1), pp. 147–54.10.1016/j.msea.2009.04.067 ↗
37. G. Scavino, C. Di Salvo, P. Matteis, R. Sesana and D. Firrao: Metall. Mater. Trans. A, 2013, vol. 44A(2), pp. 787-92.10.1007/s11661-012-1445-5 ↗
38. M. Ghasri-Khouzani and J. R. McDermid: Mater. Sci. Eng. A, 2015, vol. 621, pp. 118-27.10.1016/j.msea.2014.10.042 ↗
39. Y. J. Dai, B. Li, H. E. Ma and C. Zhang: Appl. Mech. Mater., 2015, vol. 710, pp. 9-14.10.4028/www.scientific.net/AMM.710.9 ↗
40. M. Iker, D. Gaude-Fugarolas, P. J. Jacques and F. Delannay, Proceedings of Thermec 2006, The Minerals, Metals, Materials Society, Vancouver, 2006.
41. Y. Dai, D. Tang, Z. Mi, H. Jiang and J. Lv: J. Mater. Eng., 2009, vol. 37(7), pp. 39-42.
42. L. Bracke: Doctoral Thesis, Ghent University, Belgium, 2007.
43. S. Allain, J. P. Chateau, D. Dahmoun and O. Bouaziz: Mater. Sci. Eng. A, 2004, vol. 387, pp. 272-76.10.1016/j.msea.2004.05.038 ↗
44. O. Bouaziz, S. Allain and Y. Estrin: Scripta Mater., 2010, vol. 62(9), pp. 713-15.10.1016/j.scriptamat.2010.01.040 ↗
45. S. Allain, P. Cugy, C. Scott, J. P. Chateau, A. Rusinek and A. Deschamps: Int. J. Mater. Res., 2008, vol. 99(7), pp. 734-38.10.3139/146.101693 ↗
46. I. Gutierrez-Urrutia, S. Zaefferer and D. Raabe: Scripta Mater., 2009, vol. 61(7), pp. 737-40.10.1016/j.scriptamat.2009.06.018 ↗
47. P. Hähner: Acta Mater., 1997, vol. 45(9), pp. 3695-3707.10.1016/S1359-6454(97)00066-9 ↗