A Numerical Simulation for Dissimilar Aluminum Alloys Joined by Friction Stir Welding
Source abstract
Abstract
Dissimilar aluminum alloy sheets of 2017A-T451 and 7075-T651 (6 mm thickness) were friction stir welded in a butt weld configuration. A numerical simulation of the joining process was developed to visualize the material flow patterns and temperature distribution and to correlate the microstructure to the hardness behavior. Due to the complementary downward flow of surface material into the workpiece thickness and upward flow of mid-plane and bottom-plane material, the weld nugget is composed of alternating layers of 7075 and 2017A. These layers have unique temperature histories depending on the material’s initial location within the cross section; therefore, they also have distinctive precipitate distributions. Supersaturated surface material flows into the process zone and forms a core in which GP zones reprecipitate upon cooling. Mid-plane and bottom-plane material flow toward the workpiece surface and encompass the surface material core. Within this region, the weld temperatures overage the equilibrium θ phase in 2017A, decreasing the hardness, and at the same time, dissolve the equilibrium η/T phase in the 7075, leading to reprecipitation of GP zones upon cooling and a hardness recovery.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. M.B. Uday, M.N. Ahmad Fauzi, H. Zuhailawati, and A.B. Ismail: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 534–558.10.1179/136217110X12785889550064 ↗
2. P.L. Threadgill, A.J. Leonard, H. R. Shercliff, and P.J. Withers: Int. Mater. Rev., 2009, vol. 54, pp. 49–93.10.1179/174328009X411136 ↗
3. T. DebRoy and H.K.D.H. Bhadeshia: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 266–270.10.1179/174329310X12726496072400 ↗
4. L.E. Murr: J. Mater. Eng. Perform., 2010, vol. 19, pp. 1071–1089.10.1007/s11665-010-9598-0 ↗
5. Kumar N., Yuan W., Mishra R.S.: Friction Stir Welding of Dissimilar Alloys and Materials, Butterworth-Heinemann (Elsevier), Oxford, 2015.10.1016/B978-0-12-802418-8.00002-3 ↗
6. P.A. Colgrove and H.R. Shercliff: Sci. Technol. Weld. Join., 2003, vol. 8, pp. 360–68.10.1179/136217103225005534 ↗
7. J.D. Robson and L. Campbell: Sci. Technol. Weld. Join., 2010, vol. 15, pp. 171–76.10.1179/136217109X12590746472616 ↗
8. D. Jacquin, B. de Meester, A. Simar, D. Deloison, F. Montheillet,and C. Desrayaud: J. Mater. Process. Technol., 2011, vol. 211, pp. 57 – 65.10.1016/j.jmatprotec.2010.08.016 ↗
9. D.M. Neto and P. Neto: Int. J. Adv. Manuf. Tech., 2013, vol. 65, pp. 115–126.10.1007/s00170-012-4154-8 ↗
10. M. St. Węglowski and S. Dymek: Arch. Metall. Mater., 2012, vol. 57, pp. 71–78.
11. M. St. Węglowski, A. Pietras, S. Dymek and C. Hamilton: Key Eng. Mater., 2012, vol. 504 – 506, pp. 1231 – 1236.10.4028/www.scientific.net/KEM.504-506.1231 ↗
12. I. Kalemba, C. Hamilton and S. Dymek: Mater. Design, 2014, vol. 60, pp. 295–301.10.1016/j.matdes.2014.04.009 ↗
13. C. Hamilton, M. Kopyściański, O. Senkov and S. Dymek: Metall. Mater. Trans. A., 2013, vol. 44, pp. 1730 – 1740.10.1007/s11661-012-1512-y ↗
14. S. Serajzadeh, S. Ranjbar-Motlagh, S.M.H. Mirbagher and J.M. Akhgar: Mater. Des., 2015, vol. 67, pp. 318–323.10.1016/j.matdes.2014.11.042 ↗
15. P.A. Colegrove and H.R. Shercliff: Sci. Technol. Weld. Join., 2003, vol. 8, pp. 360–368.10.1179/136217103225005534 ↗
16. C. Hamilton, M. St. Weglowski and S. Dymek: Metal. Mater. Trans. B., vol. 46B, 2015, pp. 1409–1418.10.1007/s11663-015-0340-z ↗
17. J.A. Bailey, S.L. Haas, and M.K. Shah: Int. J. Mech. Sci., 1972, vol. 14, pp. 735–754.10.1016/0020-7403(72)90012-4 ↗
18. P. A. Colegrove, H. R. Shercliff and R. Zettler: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 284 – 297.10.1179/174329307X197539 ↗
19. C. Hamilton, S. Dymek and A. Sommers: Int. J. Mach. Tools Manuf., 2008, vol. 48, pp. 1120 – 1130.10.1016/j.ijmachtools.2008.02.001 ↗
20. C. Hamilton, A. Sommers and S. Dymek: Int. J. Mach. Tool. Manu., 2009, vol. 49, pp. 230 – 238.10.1016/j.ijmachtools.2008.11.004 ↗
21. I. Kalemba, C. Hamilton and S. Dymek: Mater. Des., 2014, vol. 60, pp. 295–301.10.1016/j.matdes.2014.04.009 ↗
22. Y.S. Sato, Y. Kurihara, and H. Kokawa: Proceedings of the 6th International FSW Symposium, Saint-Sauveur, QC, Canada, 2006.
23. S.A.Khodir and T. Shibayanagi: Materials Transactions, 2007, vol. 48, pp. 1928–1937.10.2320/matertrans.MRA2007042 ↗
24. P. Bahemmat, M. Haghpanahi, M.K.B. Givi and K.R. Seighalani: Int. J. Adv. Manuf. Technol., vol. 59, 2012, pp. 939–953.10.1007/s00170-011-3547-4 ↗
25. S.A. Khodir and T. Shibayanagi: Mater. Sci. Eng. B, vol. 148, 2008, pp. 82-87.10.1016/j.mseb.2007.09.024 ↗
26. A.P. Reynolds: Sci. Technol. Weld. Join., 2000, vol. 5, pp. 120 – 124.10.1179/136217100101538119 ↗
27. M. Hartel, S. Wagner, P Frint and M. Wagner: Mater. Sci. Eng., 2014, vol. 63, pp. 1 – 10.
28. D.J. Lloyd and M.C. Chaturvedi: J. Mater. Sci., 1982, vol. 17, pp. 1819 – 1824.10.1007/BF00540811 ↗