Sintering High Tungsten Content W-Ni-Fe Heavy Alloys by Microwave Radiation
Source abstract
Abstract
This paper presents a detailed study of microwave (MW) sintering of W-Ni-Fe heavy alloys (WHAs) with tungsten (W) content 90 to 98 mass pct (Ni and Fe mass ratio of 7 to 3) in comparison with conventional (CV) hydrogen sintering. Experimental results show that WHAs were MW sintered to fully dense (≥99 pct of theoretical) when heated to sintering temperatures at a heating rate of 50 K/min to 80 K/min (50 C/min to 80 C/min) and isothermally held for 2 to 10 minutes, with sintering cycle times of only 25 to 35 minutes (excluding the cooling time). The desired microstructures of finer W grains, more matrix phases, and lower W contiguity (in 95W and 98W) were produced compared to the counterparts by CV sintering. Such microstructural features offered the alloys excellent tensile properties: ultimate tensile strengths (UTS) 1080 to 1110 MPa and tensile elongation 22.1 to 26.8 pct in 90 to 95W, and UTS 920 MPa and elongation 11.2 pct in 98W. MW sintering appeared to be more effective in fabricating WHAs with W content ≥95 pct. It was observed that the superior UTS with MW-sintered alloys was mainly due to the fast heating and shortened isothermal holding times. Prolonged sintering led to substantial grain coarsening as a result of faster tungsten grain growth in MW sintering, and consequently deteriorated the tensile properties. The grain growth rate constant K achieved was calculated to be 5.1 μm3/s for MW sintering compared to 2.9 μm3/s for CV sintering. Fast heating and short isothermal holding times are thus suggested for the fabrication of WHAs by MW sintering.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Microwave-Assisted Synthesis and Applications · Materials Engineering and Processing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. J.C. Willams: Microwave processing of materials, National Academy Press, Washington DC, 1994, pp.73–77.
2. D.E. Clark and W.H. Sutton: Annu. Rev. Mater. Sci., 1996, vol. 26, pp. 299-331.10.1146/annurev.ms.26.080196.001503 ↗
3. E.T. Thostenson and T.-W. Chou: Composites Part A: Applied Science and Manufacturing, 1999, vol. 30, pp. 1055-1071.10.1016/S1359-835X(99)00020-2 ↗
4. M. Gupta, W.W. Leong and Eugene: Microwaves and Metals, Wiley, Singapore, 2007.10.1002/9780470822746 ↗
5. M. Oghbaei and O. Mirzaee: J. Alloys Compd., 2010, vol. 494, pp. 175-189.10.1016/j.jallcom.2010.01.068 ↗
6. R. Roy, D. Agrawal and J. Cheng, S. Gedevanishvili: Nature, 1999, vol. 339, pp. 668-670.10.1038/21390 ↗
7. R.M. Anklekar, D.K. Agrawal and R. Roy: Powder Metall., 2001, vol. 44, pp. 355-362.10.1179/003258901666536 ↗
8. M. Jain, G. Skandan, K. Martin, K. Cho, B. Klotz, R. Dowding, D. Kapoor, D. Agrawal and J. Cheng: Int. J. Powder Metall., 2006, vol. 42, pp. 45-50.
9. K. Saitou: Scripta Mater., 2006, vol. 54, pp. 875-879.10.1016/j.scriptamat.2005.11.006 ↗
10. M.E. Alam and M. Gupta: Powder Metall., 2009, vol. 52, pp. 105-110.10.1179/174329008X284895 ↗
11. S.D. Luo, M. Yan, G.B. Schaffer and M. Qian: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 2466-2474.10.1007/s11661-011-0645-8 ↗
12. A. Chatterjee, T. Basak and K.G. Ayappa: AIChE J., 1998, vol. 44, pp. 2302-2311.10.1002/aic.690441019 ↗
13. K.I. Rybakov, V.E. Semenov, S.E. Egorov, A.G. Eremeev, I.V. Plotnikov and Yu.V. Bykov: J. Appl. Phys., 2006, vol. 99, pp. 023506.10.1063/1.2159078 ↗
14. V.D. Buchelnikov, D.V. Louzguine-Luzgin, G. Xie, S. Li, N. Yoshikawa, M. Sato, A.P. Anzulevich, I.V. Bychkov and A. Inoue: J. Appl. Phys., 2008, vol. 104, pp. 113505110.10.1063/1.3009677 ↗
15. P. Villars, A. Prince, and H. Okamoto: Handbook of Ternary Alloy Phase Diagram, ASM International, Materials Park, OH, 1997, vol. 8, p. 10670.
16. R.M. German: Liquid phase sintering, Plenum Press, New York, 1985, pp. 133-145.10.1007/978-1-4899-3599-1 ↗
17. L.L. Bourguignon and R.M. German: Int. J. Powder Metall., 1988, vol. 24, pp. 115-121.
18. B.H. Rabin and R.M. German: Metall. Trans. A, 1988, vol. 19, pp. 1523-1532.10.1007/BF02674026 ↗
19. A. Upadhyaya, S.K. Tiwari and P. Mishra: Scripta Mater., 2007, vol. 56, pp. 5-8.10.1016/j.scriptamat.2006.09.010 ↗
20. A. Mondal, A. Upadhyaya and D. Agrawal: Mater. Sci. Eng. A, 2010, vol. 527, pp. 6870-6878.10.1016/j.msea.2010.07.074 ↗
21. A. Mondal, A. Upadhyaya and D. Agrawal: J. Alloys Compd., 2011, vol. 509, pp. 301-310.10.1016/j.jallcom.2010.09.008 ↗
22. C.S. Zhou, J.H. Yi, S.D. Luo, Y.D. Peng, L.Y. Li and G. Chen: J. Alloys Compd., 2009, vol. 482, pp. 6-8.10.1016/j.jallcom.2009.03.176 ↗
23. C.S. Zhou, J.H. Yi, S.D. Luo, Y.D. Peng and G. Chen: Trans. Nonferrous Met. Soc. China, 2009, vol. 19, pp. 1601-1607.
24. C.S. Zhou, J.H. Yi, S.D. Luo, Y.D. Peng and H.Z. Wang: Mater. Sci. Eng. Powder Metall., 2010, vol. 15, pp. 300-304.
25. C. Zhao, J. Vleugels, C. Groffils, P.J. Luypaert and O. Van Der Biest: Acta Mater., 2000, vol. 48, pp. 3795-3801.10.1016/S1359-6454(00)00160-9 ↗
26. R.M. German, A. Bose and S.S. Mani: Metall. Trans. A, 1992, vol. 23, pp. 211-229.10.1007/BF02660866 ↗
27. A. Bose and R.M. German: Metall. Trans. A, 1988, vol. 19, pp. 2467-2476.10.1007/BF02645474 ↗
28. E. Breval, J.P. Cheng, D.K.Agrawal, P. Gigl, M. Dennis, R. Roy, A.J. Papworth Mater. Sci. Eng. A, 2005, vol. 391, pp. 285-295.10.1016/j.msea.2004.08.085 ↗
29. R.M. German, L.L. Bourguignon and B.H. Rabin: JOM, 1985, vol. 37. pp. 36-39.10.1007/BF03257677 ↗
30. R.M. German, A. Bose and S.S. Mani: Metall. Trans. A, 1992, vol. 23A, pp. 211-219.10.1007/BF02660866 ↗
31. P.W. Voorhees and M.E. Glicksman: Metall. Trans. A, 1984, vol. 15, pp. 1081-1088.10.1007/BF02644701 ↗
32. A. Bose and R.M. German: Metall. Trans. A, 1988, vol.19, pp. 3100-3103.10.1007/BF02647738 ↗
33. S.J. Park, J.M. Martin, J.F. Guo, J.L. Johnson and R.M. German: Metall. Mater. Trans. A, 2006, vol. 37, pp. 3337-3346.10.1007/BF02586168 ↗
34. M.A. Janney, H.D. Kimrey, M.A. Schmidt and J.O. Kiggans: J. Am. Cer. Soc., 1991, vol. 74, pp. 1675-1681.10.1111/j.1151-2916.1991.tb07159.x ↗
35. Y.V. Bykov, S.V. Egorov, A.G. Eremeev, K.I. Rybakov, V.E. Semenov, A.A. Sorokin and S.A. Gusev: J. Mater. Sci., 2002, vol. 36, pp. 131-136.10.1023/A:1004893104413 ↗