journal article·2012-06

Microstructures, Mechanical and Chemical Properties of TLP-Bonded Joints in a Duplex Stainless Steel with Amorphous Ni-Based Insert Alloys

Xinjian Yuan, Myung Bok Kim, Young Ho Cho, Chung Yun Kang

Publisher page

Abstract

The changes in tensile strength and pitting corrosion resistance of transient liquid-phase (TLP)-bonded joints for a duplex stainless steel with MBF-80, MBF-30, and MBF-35 as functions of holding time and filler were interpreted with respect to the bond microstructure. Using MBF-80 after 300 seconds, the fracture strength of the joint reached the maximum value. The failure was dependent on the interplay between the reduction in residual liquid and the increase in interface precipitates. After 3600 seconds, the joint strength had the minimum value. At the same conditions, the tensile strength for MBF-80 was low compared with MBF-35 and MBF-30. In contrast with the tensile strength, the joint produced with MBF-80 for 3600 seconds exhibited the best corrosion resistance. Among the fillers used, the corrosion resistance of the joint using MBF-80 close to that of the substrate could be related intimately to the existence of Cr in this filler.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. K. Nishimoto, K. Saida, D. Kim, and Y. Nakao: ISIJ Int., 1995, vol. 35, pp. 1298–1306.10.2355/isijinternational.35.1298 ↗
2. X. Wu, R.S. Chandel, and H. Li: J. Mater. Sci., 2001, vol. 36, pp. 1539–46.10.1023/A:1017513200502 ↗
3. W. Li, T. Jin, X.F. Sun, Y. Guo, H.R. Guan, and Z.Q. Hu: Scripta Mater., 2003, vol. 48, pp. 1283–88.10.1016/S1359-6462(03)00045-9 ↗
4. O.A. Idowu, O.A. Ojo, and M.C. Chaturvedi: Mater. Sci. Eng. A, 2005, vol. 397A, pp. 98–112.10.1016/j.msea.2005.01.055 ↗
5. N.P. Wikstrom, O.A. Ojo, and M.C. Chaturvedi: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2787–96.
6. F. Jalilian, M. Jahazi, and R.A.L. Drew: Mater. Sci. Eng. A, 2006, vol. 423A, pp. 269–81.10.1016/j.msea.2006.02.030 ↗
7. M. Mosallaee, A. Ekrami, K. Ohsasa, and K. Matsuura: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 2389–2402.10.1007/s11661-008-9588-0 ↗
8. K. Tokoro, N.P. Wikstrom, O.A. Ojo, and M.C. Chaturvedi: Mater. Sci. Eng. A, 2008, vol. 477A, pp. 311–18.10.1016/j.msea.2007.05.069 ↗
9. A.T. Egbewande, C. Chukwukaeme, and O.A. Ojo: Mater. Charact., 2008, vol. 59, pp. 1051–58.10.1016/j.matchar.2007.08.023 ↗
10. M.M. Abdelfatah and O.A. Ojo: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 377–85.10.1007/s11661-008-9726-8 ↗
11. N.D. Luozzo, M. Fontana, and B. Arcondo: J. Mater. Sci., 2007, vol. 42, pp. 4044–50.10.1007/s10853-006-0190-9 ↗
12. N.D. Luozzo, M. Fontana, and B. Arcondo: J. Mater. Sci., 2008, vol. 43, pp. 4938–44.10.1007/s10853-008-2720-0 ↗
13. R. Kaçar and O. Baylan: Mater. Des., 2004, vol. 25, pp. 317–29.10.1016/j.matdes.2003.10.010 ↗
14. M.A. Arafin, M. Medraj, D.P. Turner, and P. Bocher: Mater. Chem. Phys., 2007, vol. 106, pp. 109–09.10.1016/j.matchemphys.2007.05.049 ↗
15. G. Humpston and D.M. Jacobson: Principles of Soldering and Brazing, ASM International, Materials Park, OH, 1993, pp. 128–32.
16. L.H. Chiu, W.C. Hsieh, and C.H. Wu: Mater. Sci. Eng. A, 2003, vol. 354A, pp. 82–91.10.1016/S0921-5093(02)00911-5 ↗
17. T.I. Khan, M.J. Kabir, and R. Bulpett: Mater. Sci. Eng. A, 2004, vol. 372A, pp. 290–95.10.1016/j.msea.2004.01.023 ↗
18. X.J. Yuan, C.Y. Kang, and M.B. Kim: Mater. Charact., 2009, vol. 60, pp. 923–31.10.1016/j.matchar.2009.03.004 ↗
19. X.J. Yuan, M.B. Kim, and C.Y. Kang: Mater. Charact., 2009, vol. 60, pp. 1289–97.10.1016/j.matchar.2009.05.012 ↗
20. X.J. Yuan, M.B. Kim, and C.Y. Kang: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 1310–24.10.1007/s11661-010-0534-6 ↗
21. T.H. Chen and J.R. Yang: Mater. Sci. Eng. A, 2001, vol. 311A, pp. 28–41.10.1016/S0921-5093(01)00911-X ↗
22. ASTM Designation (G48-03): Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution, ASTM International, 2009.
23. M. Pouranvari, A. Ekrami, and A.H. Kokabi: Mater. Sci. Eng. A, 2008, vol. 490A, pp. 229–34.10.1016/j.msea.2008.01.032 ↗
24. ASM Handbook: Alloy Phase Diagram, vol. 3, ASM, Materials Park, OH, 1992, pp. 426–27.
25. B. Predel: Physical Chemistry: Phase Equilibria Crystallographic Data and Values of Thermodynamic Properties of Binary Alloys, Springer-Verlag, Berlin, Germany, 1992, p.15.
26. J.-D. Schöbel and H.H. Stadelmaier: Z. Metallkde, 1965, vol. 56, pp. 856–59.
27. T.B. Massalski: Binary Alloy Phase Diagrams, ASM, Materials Park, OH, 1986, pp. 366–71.
28. W.F. Gale and E.R. Wallach: Mater. Sci. Technol., 1991, vol. 7, pp. 1143–48.10.1179/mst.1991.7.12.1143 ↗
29. O.A. Ojo, N.L. Richards, and M.C. Chaturvedi: Sci. Technol. Weld. Join., 2004, vol. 9, pp. 532–40.10.1179/174329304X8702 ↗
30. W.C. Wu, H.Q. Feng, and K.Z. Wu: Handbook for Standard Electrode Potentials, Science Press, Beijing, China, 1991, pp. 92–100.