journal article·2016-11

Effect of Weld Characteristic on Mechanical Strength of Laser-Arc Hybrid-Welded Al-Mg-Si-Mn Aluminum Alloy

Chen Zhang, Ming Gao, Ming Jiang, Xiaoyan Zeng

Publisher page

Abstract

Laser-arc hybrid welding (LAHW) was employed to improve the tensile properties of the joints of 8-mm-thick Al-Mg-Si-Mn alloy (AA6082) using Al-5Mg filler wire. The weld microstructures were examined by scanning electron microscope, electron backscattered diffraction, and transmission electron microscopy in detail. The LAHW joints with pore-free and high-tensile performances were obtained. The strength enhancement of the fusion zone and heat-affected zone in the LAHW joint was mainly attributed to the grain refinement strengthening and the precipitation strengthening, respectively. The microstructure characteristics were related to the effects of laser-arc interaction on the energy transfer within the molten pool. The arc caused the majority of laser energy to dissipate out of the keyhole, and then it reduced the heat input. The lower heat input refined the grain size, weakened the overaging effect, and thus improved the tensile strength.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. [1] P. Von Witzendorff, S. Kaierle, O. Suttmann, and L. Overmeyer: Metall. Mater. Trans. A, 2015, vol. 46, pp. 1678-88.10.1007/s11661-015-2749-z ↗
2. [2] L. Wan, Y. Huang, W. Guo, S. Lv, and J. Feng: J. Mater. Sci. Technol., 2014, vol. 30, pp. 1243-50.10.1016/j.jmst.2014.04.009 ↗
3. [3] Y. Ruan, X. Qiu, W. Gong, D. Sun, and Y. Li: Mater. Design., 2012, vol. 35, pp. 20-4.10.1016/j.matdes.2011.09.002 ↗
4. [4] M. Cabibbo, A. Forcellese, M. El Mehtedi, and M. Simoncini: Mat. Sci. Eng. A-Struct., 2014, vol. 590, pp. 209-17.10.1016/j.msea.2013.10.031 ↗
5. [5] T. Graf and H. Staufer: Weld. J., 2003, vol. 82, p. 42.
6. [6] P. Moore, D. Howse, and E. Wallach: Sci. Technol. Weld. Joi., 2004, vol. 9, pp. 314-22.10.1179/136217104225021652 ↗
7. [7] S. Katayama, S. Uchiumi, M. Mizutani, J. Wang, and K. Fujii: Weld. Int., 2007, vol. 21, pp. 25-31.10.1533/wint.2007.3680 ↗
8. C.T. Frank Vollertsen: ICALEO 2005, LIA, Florida, 2005, p. 506.10.2351/1.5060499 ↗
9. [9] H. Yonetani: Weld. Int., 2008, vol. 22, pp. 701-4.10.1080/09507110802465050 ↗
10. [10] J. Shen, L. Wen, Y. Li, and D. Min: Mat. Sci. Eng. A-Struct., 2013, vol. 578, pp. 303-9.10.1016/j.msea.2013.04.093 ↗
11. [11] I. Tomashchuk, D. Grevey, and P. Sallamand: Mat. Sci. Eng. A-Struct., 2015, vol. 622, pp. 37-45.10.1016/j.msea.2014.10.084 ↗
12. M. Sheikhi, F. Malek Ghaini, and H. Assadi: Sci. Technol. Weld. Join., 2014, vol. 19, pp. 250-5.10.1179/1362171813Y.0000000190 ↗
13. [13] G. Cam and M. Kocak: Int. Mater. Rev., 1998, vol. 43, pp. 1-44.10.1179/imr.1998.43.1.1 ↗
14. [14] G. Casalino, M. Mortello, P. Leo, K.Y. Benyounis, and A.G. Olabi: Mater. Design., 2014, vol. 61, pp. 191-8.10.1016/j.matdes.2014.04.060 ↗
15. [15] O. Ola and F. Doern: Int. J. Adv. Manuf. Tech, 2015, vol. 80, pp. 3-10.10.1007/s00170-015-6987-4 ↗
16. [16] P.D. Lee and J.D. Hunt: Acta Mater., 2001, vol. 49, pp. 1383-98.10.1016/S1359-6454(01)00043-X ↗
17. [17] M. Gao, H.-G. Tang, X.-F. Chen, and X.-Y. Zeng: Mater. Design., 2012, vol. 42, pp. 46-54.10.1016/j.matdes.2012.05.034 ↗
18. [18] Z. Wang, M. Gao, H. Tang, and X. Zeng: Mater. Charact., 2011, vol. 62, pp. 943-51.10.1016/j.matchar.2011.07.002 ↗
19. [19] C. He, C.X. Huang, Y.J. Liu, J.K. Li, and Q. Wang: Mater. Design., 2015, vol. 65, pp. 289-96.10.1016/j.matdes.2014.08.050 ↗
20. [20] J. Yan, X. Zeng, M. Gao, J. Lai, and T. Lin: Appl. Surf. Sci., 2009, vol. 255, pp. 7307-13.10.1016/j.apsusc.2009.03.088 ↗
21. [21] Z. Gao, J. Fang, Y. Zhang, G. Ran, and S. Zhang: Int. J. Electrochem. Sci., 2013, vol. 8, pp. 7905-17.10.1016/S1452-3981(23)12856-2 ↗
22. [22] C. Zhang, M. Gao, G. Li, C. Chen, and X. Zeng: Sci. Technol. Weld. Joi., 2013, vol. 18, pp. 703-10.10.1179/1362171813Y.0000000153 ↗
23. [23] B. Hu and I.M. Richardson: Mat. Sci. Eng. A-Struct., 2007, vol. 459, pp. 94-100.10.1016/j.msea.2006.12.094 ↗
24. [24] S. Yan, H. Chen, Z. Zhu, and G. Gou: Mater. Design., 2014, vol. 61, pp. 160-7.10.1016/j.matdes.2014.04.062 ↗
25. [25] G. Liu, G.J. Zhang, R.H. Wang, W. Hu, J. Sun, and K.H. Chen: Acta Mater., 2007, vol. 55, pp. 273-84.10.1016/j.actamat.2006.08.026 ↗
26. [26] A. Alankar, I.N. Mastorakos, and D.P. Field: Acta Mater., 2009, vol. 57, pp. 5936-46.10.1016/j.actamat.2009.08.028 ↗
27. [27] M. Crumbach, M. Goerdeler, and G. Gottstein: Acta Mater., 2006, vol. 54, pp. 3291-306.10.1016/j.actamat.2006.03.019 ↗
28. [28] S. Katayama, Y. Naito, S. Uchiumi, and M. Mizutani: Trans. JWRI, 2006, vol. 35, p. 13.
29. [29] R. Kumar, U. Dilthey, D. Dwivedi, and P. Ghosh: Mater. Design., 2009, vol. 30, pp. 306-13.10.1016/j.matdes.2008.04.073 ↗
30. [30] M. Ericsson and R. Sandström: Int. J. Fatigue., 2003, vol. 25, pp. 1379-87.10.1016/S0142-1123(03)00059-8 ↗
31. [31] M. Scott and M. Gittos: Weld. J., 1983, vol. 62, pp. 243s-52s.
32. [32] L. Hector Jr, Y.-L. Chen, S. Agarwal, and C. Briant: Metall. Mater. Trans. A, 2004, vol. 35, pp. 3032-38.10.1007/s11661-004-0047-2 ↗
33. D.H. Lee, J.H. Park, and S.W. Nam: Mater. Sci. Technol. Lond., 1999, vol. 15, pp. 450-5.10.1179/026708399101505923 ↗
34. [34] W. Woo, H. Choo, D.W. Brown, and F. Zhili: Metall. Mater. Trans. A, 2007, vol. 38, pp. 69-76.10.1007/s11661-006-9034-0 ↗
35. [35] G. Edwards, K. Stiller, G. Dunlop, and M. Couper: Acta Mater., 1998, vol. 46, pp. 3893-904.10.1016/S1359-6454(98)00059-7 ↗
36. [36] Y.S. Sato, H. Kokawa, M. Enomoto, S. Jogan, and T. Hashimoto: Metall. Mater. Trans. A, 1999, vol. 30, pp. 3125-30.10.1007/s11661-999-0223-5 ↗
37. [37] C. Genevois, A. Deschamps, A. Denquin, and B. Doisneau-Cottignies: Acta Mater., 2005, vol. 53, pp. 2447-58.10.1016/j.actamat.2005.02.007 ↗
38. [38] K. Kendig and D. Miracle: Acta Mater., 2002, vol. 50, pp. 4165-75.10.1016/S1359-6454(02)00258-6 ↗
39. [39] X. Feng, H. Liu, and S. Suresh Babu: Scripta Mater., 2011, vol. 65, pp. 1057-60.10.1016/j.scriptamat.2011.09.009 ↗
40. [40] M. Gao, S. Mei, Z. Wang, X. Li, and X. Zeng: J. Mater. Process. Tech., 2012, vol. 212, pp. 1338-46.10.1016/j.jmatprotec.2012.01.011 ↗
41. [41] B. Hu and G. Den Ouden: Sci. Technol. Weld. Joi., 2005, vol. 10, pp. 76-81.10.1179/174329305X29537 ↗
42. [42] R. Fabbro, S. Slimani, F. Coste, and F. Briand: J. Phys. D. Appl. Phys., 2005, vol. 38, pp. 1881.10.1088/0022-3727/38/12/005 ↗
43. [43] Z. Gao, Y. Wu, and J. Huang: Int. J. Adv. Manuf. Tech., 2009, vol. 44, pp. 870-9.10.1007/s00170-008-1896-4 ↗
44. [44] J.-H. Cho and S.-J. Na: J. Phys. D. Appl. Phys., 2006, vol. 39, p. 5372.10.1088/0022-3727/39/24/039 ↗
45. [45] X. Jin, L. Li, and Y. Zhang: J. Phys. D. Appl. Phys., 2002, vol. 35, p. 2304.10.1088/0022-3727/35/18/312 ↗
46. [46] Y. Cheng, X. Jin, S. Li, and L. Zeng: Opt. Laser Technol., 2012, vol. 44, pp. 1426-36.10.1016/j.optlastec.2011.12.024 ↗