Hardness, Microstructure, and Residual Stresses in Low Carbon Steel Welding with Post-weld Heat Treatment and Temper Bead Welding
Source abstract
Abstract
This paper investigates the effects of post-weld heat treatment (PWHT) and temper bead welding (TBW) on hardness, microstructure and residual stresses in multi-layer welding on low carbon steel specimens made with two different weld geometries, viz. (1) smooth-contoured and (2) U-shaped. It was found that the PWHT technique gave overall lower hardness than the TBW technique, but the hardness values in both techniques were acceptable. Microscopy analysis showed that the TBW technique was more effective in tempering the heat affected zone as the grain size decreased slightly at the fusion line in spite of the higher temperature at the fusion line. Residual stresses measured using the hole-drilling method showed that the residual stress is not reduced below yield stress near the last bead solidified in TBW. Only PWHT gives low residual stress results in this area. High tensile residual stresses may result in sensitivity to fatigue loading.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Bilmes, P.D., Solari, M., and Llorente, C.L., 2001, Mater. Charact., 46(4) pp. 285-96.10.1016/S1044-5803(00)00099-1 ↗
2. Ilić, N., Jovanović, M.T., Todorović, M., 1999, Mater. Charact., 43(4) pp. 243-50.10.1016/S1044-5803(99)00006-6 ↗
3. Paradowska, A. M., Price, J. W. H., Kerezsi, B., 2010, Eng. Fail. Anal., 17(1) pp. 320-27.10.1016/j.engfailanal.2009.06.016 ↗
4. Tawfik, D., Mutton, P.J., and Chiu, W.K., 2008, J. Mater. Process. Technol., 196(1-3) pp. 279-91.10.1016/j.jmatprotec.2007.05.055 ↗
5. C.D. Lundin: Weld. Res. Council Bull., 1996, vol. 412, pp. 16–26.
6. T. Shehata: Ph.D. Thesis, Monash University, Australia, 2005.
7. D.W. Gandy, and R. Viswanathan: Weld. Res. Council Bull., 1996, vol. 412, pp. 43–59.
8. C.D. Lundin: Weld. Res. Council Bull., 1996, vol. 412, pp. 43–59, pp. 16–26.
9. J.H. Kiefer, Weld. J., 1995, vol. 74 (11), pp. 363–367.
10. Arivazhagan, B., Sundaresan, S., and Kamaraj, M., 2009, J. Mater. Process. Technol., 209(12-13) pp. 5245-53.10.1016/j.jmatprotec.2009.02.006 ↗
11. Balasubramanian, V., and Guha, B., 1999, Mater. Sci. Eng: A, 265(1-2) pp. 7-17.10.1016/S0921-5093(99)00007-6 ↗
12. Palani, P.K., and Murugan, N., 2006, J. Manuf. Process., 8(2) pp. 90-100.10.1016/S1526-6125(06)80004-6 ↗
13. Yang, K., Zhang, Z., Hu, W., 2011, Int. J. Iron Steel Res. 18(11) pp. 74-79.10.1016/S1006-706X(11)60120-9 ↗
14. Aloraier, A.S., and Joshi, S., Mater. Sci. Eng. A., 534 (2012), pp. 13-21.10.1016/j.msea.2011.10.107 ↗
15. American Society of Mechanical Engineers, Boiler and Pressure Vessel, Section VIII, Division 1&2, ASME, NY, 1992.
16. AS 4458-1997/Amdt. No. 1-99: Pressure equipment—Manufacture, Standards Australia.
17. A.S. Aloraier, S. Joshi, J.W.H. Price and K. Alawadhi, Int. J. Press. Vessels Pip., 111-112 (2013), pp. 269-78.10.1016/j.ijpvp.2013.09.002 ↗
18. AWS A5.20-95: Carbon Steel Electrodes for Flux Cored Arc Welding, American Welding Society, Miami.
19. Bailey, N., 1994, “Weldability of Ferritic Steels,” Woodhead Publishing, Cambridge, UK.10.1533/9781845698935 ↗
20. AS 2205.6.1-97: Methods for Destructive Testing of Welds in Metal—Weld Joint Hardness Test, Standards Australia.
21. Friedman, L.M., 1996, Weld. Res. Council Bull., 1996, vol. 412, pp. 43–59, pp. 27–34.
22. Lau, T.W., and Lau, M.L., 1996, Weld. Res. Council Bull., 1996, vol. 412, pp. 35–42.
23. J. Hildebrand: Ph.D. Thesis, Institute of Structural Engineering, Bauhaus-Universität Weimar, Germany, 2009.