Effects of Different Modes of Hot Cross-Rolling in 7010 Aluminum Alloy: Part II. Mechanical Properties Anisotropy
Source abstract
Abstract
The influence of microstructure and texture developed by different modes of hot cross-rolling on in-plane anisotropy (AIP) of yield strength, work hardening behavior, and anisotropy of Knoop hardness (KHN) yield locus has been investigated. The AIP and work hardening behavior are evaluated by tensile testing at 0 deg, 45 deg, and 90 deg to the rolling direction, while yield loci have been generated by directional KHN measurements. It has been observed that specimens especially in the peak-aged temper, in spite of having a strong, rotated Brass texture, show low AIP. The results are discussed on the basis of Schmid factor analyses in conjunction with microstructural features, namely grain morphology and precipitation effects. For the specimen having a single-component texture, the yield strength variation as a function of orientation can be rationalized by the Schmid factor analysis of a perfectly textured material behaving as a quasi-single crystal. The work hardening behavior is significantly affected by the presence of solute in the matrix and the state of precipitation rather than texture, while yield loci derived from KHN measurements reiterate the low anisotropy of the materials. Theoretic yield loci calculated from the texture data using the visco-plastic self-consistent model and Hill’s anisotropic equation are compared with that obtained experimentally.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Metal Forming Simulation Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. F.J. Humphreys and M. Hatherly: Recrystallization and Related Phenomena, Pergamon Press, Oxford, U.K., 1995.
2. J.T. Staley: Proc. Int. Conf. on Aluminum Alloys (ICAA 3), L. Arnberg, O. Lohne, E. Nes, and N. Ryum, eds., The Norwegian Institute of Technology, Trondheim, 1992, pp. 107–29.
3. W.F. Hosford (1966) Met. Eng. Q 6(4), pp. 13–19.
4. K.V. Jata, A.K. Hopkins, and R.J. Rioja: Mater. Sci. Forum, 1996, vols. 217–222, pp. 647-52.10.4028/www.scientific.net/MSF.217-222.647 ↗
5. F. Barlat, S.M. Miyasato, J. Liu, and J.C. Brem: Aluminium Alloys: Their Physical and Mechanical Properties (ICAA 4), T.H. Sanders, Jr., and E.A. Starke, Jr., eds., Georgia Institute of Technology, Atlanta, 1994, p. 389.
6. P.J. Gregson, and H.M. Flower: Acta metall., 1985, vol. 33, pp. 527-37.10.1016/0001-6160(85)90095-1 ↗
7. N.E. Prasad and G. Malakondaiah: Bull. Mater. Sci., 1992, vol. 15, pp. 297-310.10.1007/BF02747639 ↗
8. A.K. Vasudevan, M.A. Przystupa, and W.G. Fricke, Jr.: Scripta Metall. Mater., 1990, vol. 24, pp. 1429-34.10.1016/0956-716X(90)90409-A ↗
9. F. Barlat, D.J. Lege, J.C. Brem, and C.J. Warren: Textures Microstruct., 1991, vol. 14-18, pp. 1013-18.10.1155/TSM.14-18.1013 ↗
10. X.H. Zeng, M. Ahmad, and O. Engler: Mater. Sci. Technol., 1994, vol. 10, pp. 581-91.10.1179/026708394790164220 ↗
11. S. Fox, H.M. Flower, and D.S. McDarmaid: Aluminium Alloys: Their Physical and Mechanical Properties (ICAA2), E.A. Starke, Jr. and T.H. Sander, Jr., eds., University of Virginia, Charlottesville, 1986, pp. 939–50.
12. W.F. Hosford and R.H. Zeisloft: Metall. Trans., 1972, vol. 3, pp. 113-21.10.1007/BF02680590 ↗
13. H. Hargarter, M.T. Lyttle, and E.A. Starke: Mater. Sci. Eng. A, 1998, vol. A257, pp. 87-99.10.1016/S0921-5093(98)00826-0 ↗
14. R.K. Singh, A.K. Singh and N.E. Prasad: Mater. Sci. Eng. A, 2000, vol. A277, pp. 114-22.10.1016/S0921-5093(99)00549-3 ↗
15. J.J. Fundenberger, M.J. Philippe, C. Esling, P. Lequeu, and B. Chenal: Textures and Microstruct., 1993, vol. 21, pp. 93-108.10.1155/TSM.21.93 ↗
16. X.-H. Zeng, N.-E. Andersson, and S. Johansson: Proc. 11th Int. Conf. Texture of Materials (ICOTOM 11), Z. Liang, L. Zuo, and Y. Chu, eds., International Academic Publishers, Beijing, 1996, p. 1172.
17. J. Dutkiewicz and J. Bonarski: Mater. Des., 1997, vol. 18, pp. 247-52.10.1016/S0261-3069(97)00059-9 ↗
18. C. Mondal, A.K. Singh, A.K. Mukhopadhyay, and K. Chattopadhyay: Metall. Mater. Trans. A, 2013. DOI: 10.1007/s11661-013-1626-x.10.1007/s11661-013-1626-x ↗
19. R.G. Wheeler and D.R. Ireland: Electrochem. Technol., 1966, vol. 4, p. 313.
20. D. Lee and W.A. Backofen: Trans. Metall. Soc. AIME, 1966, vol. 236, pp. 1696-1704.
21. A. Fitzgibbon, M. Pilu, and R.B. Fisher: IEEE Trans. Pattern Anal. Mach. Intell., 1999, vol. 21, pp. 476-80.10.1109/34.765658 ↗
22. R.A. Lebensohn, C.N. Tome: Acta Metall. Mater., 1993, vol. 41, p. 2611.10.1016/0956-7151(93)90130-K ↗
23. C.N. Tome, G.R. Cannova, U.F. Kocks: Acta Metall. Mater., 1984, vol. 32, p. 1637.10.1016/0001-6160(84)90222-0 ↗
24. W.T. Wu and C.H. Koo: Scripta Metall. Mater., 1998, vol. 38, p. 267.
25. M.T. Lyttle and J.A. Wert: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3503-12.10.1007/BF02595442 ↗
26. A.K. Singh, A.A. Gokhale, G.G. Saha, and R.K. Ray: Textures in Materials Research, R.K. Ray and A.K. Singh, eds., Oxford and IBH Publishing Co., New Delhi, 1999, pp. 219–32.
27. D. Juul Jensen and N. Hansen: Acta Metall. Mater., 1990, vol. 38, pp. 1369-80.10.1016/0956-7151(90)90105-P ↗
28. D.A. Hughes: Scripta Metall. Mater., 1992, vol. 27, pp. 969-74.10.1016/0956-716X(92)90458-Q ↗
29. W.G. Fricke, Jr., M.A. Przystupa, and F. Barlat: Aluminium Technology 1986, T. Sheppard, ed., The Institute of Metals, London, 1986, pp. 310–16.
30. C.Q. Chen and H.X. Li: Mater. Sci. Technol., 1987, vol. 3, pp. 125-29.10.1179/026708387790122972 ↗
31. H.X. Li and C.Q. Chen: Acta Aeronaut. Astronaut. Sin., 1990, vol. 11, pp. A106-10.
32. A.K. Mukhopadhyay, K.S. Prasad, and D.S.K. Murali: Mater. Sci. Technol., 2011, vol. 27, pp. 1732-35.10.1179/026708310X12815992418292 ↗
33. V.M.J. Sharma, K.S. Kumar, B.N. Rao, and S.D. Pathak: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3186-95.10.1007/s11661-009-0062-4 ↗
34. D.C. Ludwigson: Metall. Trans., 1971, vol. 2, pp. 2825-28.10.1007/BF02813258 ↗
35. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill, London, 1988.
36. D. Lee: Science of Hardness Testing and Its Applications, J.H. Westbrook and H. Conrad, eds., ASM International, Metals Park, OH, 1973, pp. 147–65.
37. R. Hill: Proc. R. Soc. Lond. Ser. A, 1948, vol. 193, p. 281–97.10.1098/rspa.1948.0045 ↗
38. A.K. Singh, C.R. Mohan Rao and K. Srinivasan: Met. Mater. Process., 2007, vol. 19, pp. 89-100.
39. B.C. Wonsiewicz and W.W. Wilkening: Trans. Metall. Soc. AIME, 1969, vol. 245, pp. 1313-19.