Mechanical Behavior and Microstructural Development of Low-Carbon Steel and Microcomposite Steel Reinforcement Bars Deformed under Quasi-Static and Dynamic Shear Loading
Source abstract
Abstract
Reinforcement bars of microcomposite (MC) steel, composed of lath martensite and minor amounts of retained austenite, possess improved strength and corrosion characteristics over low-carbon (LC) steel rebar; however, their performance under shear loading has not previously been investigated at the microstructural level. In this study, LC and MC steel cylinders were compression tested, and specimens machined into a forced-shear geometry were subjected to quasi-static and dynamic shear loading to determine their shear behavior as a function of the strain and strain rate. The as-received and sheared microstructures were examined using optical microscopy (OM), scanning electron microscopy (SEM), and electron backscatter diffraction (EBSD). Higher-resolution microstructural examinations were performed using transmission electron microscopy (TEM). The influence of the starting microstructure on the shear behavior was found to depend strongly on the strain rate; the MC steel exhibited not only greater strain-rate sensitivity than the LC steel but also a greater resistance to shear localization with load. In both steels, despite differences in the starting microstructure, post-mortem observations were consistent with a continuous mechanism operating within adiabatic shear bands (ASBs), in which subgrains rotated into highly misoriented grains containing a high density of dislocations.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Structural Response to Dynamic Loads · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. “ASTM A615/A615M-07 Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement,” ASTM International, West Conshohocken, PA, 2007, vol. 01.04, pp. 1–6.
2. “ASTM A955/A 955M-07a Standard Specification for Deformed and Plain Stainless- Steel Bars for Concrete Reinforcement,” Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2007, vol. 01.04, pp. 1–11.
3. “ASTM A775/A775M- 07 ASTM A775/A775M-07 Standard Specification for Epoxy-Coated Steel Reinforcing Bars,” Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2007, pp. 1–10.
4. M. Arockiasamy, P.V. Vijay, B. Benmokrane, and M. Shahawy: Final Report for NCHRP Project 10-55, Florida Atlantic University, 2003, pp. 1–12.
5. G.J. Kusinski: MMFX Technologies Corporation, Irvine, CA, private communication, 2007.
6. G.G. Clemena and Y.P. Virmani: Concrete Int., 2004, vol. 26 (11), pp. 39–49.10.1176/pn.39.11.0390049 ↗
7. G.J. Kusinski, D.G. Pollack, and G. Thomas: U.S. Patent WO/2003/052152, International Bureau of WIPO, USPTO, 2006, pp. 1–11.
8. “ASTM A1035/A1035-07 Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement,” Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2007.
9. R. El-Hacha and S.H. Rizkalla: NCSU-CFL Report No. 02-04, Constructed Facilities Laboratory of NCSU, 2004.
10. Y.B. Xu, Y.L. Bai, Q. Xue, and L.T. Shen: Acta Mater., 1996, vol. 44 (5), pp. 1917–26.10.1016/1359-6454(95)00306-1 ↗
11. A. Bussiba, H. Alush, M. Kupiec, and Y. Katz: in Structures under Shock and Impact V, N. Jones, D.G. Talaslidis, C.A. Brebbia, and G.D. Manolis, eds., Computational Mechanics Publications Ltd., Thessaloniki, Greece, 1998, pp. 559–68.
12. J.A. Hines and K.S. Vecchio: Acta Mater., 1997, vol. 45 (2), pp. 635–49.10.1016/S1359-6454(96)00193-0 ↗
13. R.W. Armstrong and F.J. Zerilli: Mech. Mater., 1994, vol. 17 (2–3), pp. 319–27.10.1016/0167-6636(94)90069-8 ↗
14. S.A. Manion and T.A.C. Stock: Int. J. Fract. Mech., 1970, vol. 6 (1), pp. 106–07.10.1007/BF00183670 ↗
15. M.A. Meyers and C.L. Wittman: Metall. Trans. A, 1990, vol. 21A, pp. 3153–64.10.1007/BF02647311 ↗
16. A.L. Wingrove: Metall. Trans., 1973, vol. 4, pp. 1829–33.10.1007/BF02665409 ↗
17. C.L. Wittman, M.A. Meyers, and H.-R. Pak: Metall. Trans. A, 1990, vol. 21A, pp. 707–16.10.1007/BF02671941 ↗
18. R.L. Woodward and R.L. Aghan: Mater. Forum, 1978, vol. 1 (4), pp. 180–84.
19. J.F.C. Lins, H.R.Z. Sandim, K.S. Vecchio, and D. Raabe: Mater. Sci. Forum, 2005, vols. 495–497, pp. 393–98.10.4028/www.scientific.net/MSF.495-497.393 ↗
20. M.A. Meyers, Y.B. Xu, Q. Xue, M.T. Pérez-Prado, and T.R. McNelley: Acta Mater., 2003, vol. 51 (5), pp. 1307–25.10.1016/S1359-6454(02)00526-8 ↗
21. J.F.C. Lins, H.R.Z. Sandim, H.-J. Kestenback, D. Raabe, and K.S. Vecchio: Mater. Sci. Eng., A, 2007, vol. 457, pp. 205–18.10.1016/j.msea.2006.12.019 ↗
22. L.M. Dougherty, E.K. Cerreta, E.A. Pfeif, C.P. Trujillo, and G.T. Gray III: Acta Mater., 2007, vol. 55 (18), pp. 6356–64.10.1016/j.actamat.2007.07.051 ↗
23. E. El-Danaf, S.R. Kalidindi, R.D. Doherty, and C. Necker: Acta Mater., 2000, vol. 48 (10), pp. 2665–73.10.1016/S1359-6454(00)00050-1 ↗
24. A.P. Zhilyaev, T.R. McNelley, and T.G. Langdon: J. Mater. Sci., 2007, vol. 42 (5), pp. 1517–28.10.1007/s10853-006-0628-0 ↗
25. S. Li, A.A. Gazder, I.J. Beyerlein, E.V. Pereloma, and C.H.J. Davies: Acta Mater., 2006, vol. 43, pp. 1087–1100.10.1016/j.actamat.2005.10.042 ↗
26. A. Castellero, S.J. Lloyd, S.V. Madge, Zs. Kovacs, J.F. Loffler, M. Baricco, and A.L. Greer: J. Alloys Compd., 2007, vols. 434–435, pp. 48–51.10.1016/j.jallcom.2006.08.168 ↗
27. K.M. Cho, S. Lee, S.R. Nutt, and J. Duffy: Acta Metall. Mater., 1993, vol. 41 (3), pp. 923–32.10.1016/0956-7151(93)90026-O ↗
28. C.O. Mgbokwere, S.R. Nutt, and J. Duffy: Mech. Mater., 1994, vol. 17 (2–3), pp. 97–110.10.1016/0167-6636(94)90052-3 ↗
29. M.A. Meyers and H.-R. Pak: Acta Metall., 1986, vol. 34 (12), pp. 2493–99.10.1016/0001-6160(86)90152-5 ↗
30. Q. Xue, E.K. Cerreta, and G.T. Gray III: Acta Mater., 2007, vol. 55, pp. 691–704.10.1016/j.actamat.2006.09.001 ↗
31. C.G. Lee, W.J. Park, S. Lee, and K.S. Shin: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 477–83.10.1007/s11661-998-0128-8 ↗
32. J.A. Hines, K.S. Vecchio, and S. Ahzi: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 191–203.10.1007/s11661-998-0172-4 ↗
33. D.R. Lesuer, C.K. Syn, and O.D. Sherby: Mater. Sci. Eng., A, 2005, vols. 410–411, pp. 222–25.10.1016/j.msea.2005.08.138 ↗
34. R.C. Glenn and W.C. Leslie: Metall. Trans., 1971, vol. 2, pp. 2945–47.10.1007/BF02813279 ↗
35. E.V. Tatyanin, N.F. Borovikov, V.G. Kurdyumov, and V.L. Indendom: Phys. Solid State, 1997, vol. 39 (7), pp. 1097–99.10.1134/1.1130038 ↗
36. J.H. Giovanola: Mech. Mater., 1988, vol. 7 (1), pp. 73–87.10.1016/0167-6636(88)90007-5 ↗
37. Q. Xue and G.T. Gray III: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2447–58.10.1007/BF02586218 ↗
38. Q. Xue and G.T. Gray III: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2435–46.10.1007/BF02586217 ↗
39. C. Hill, C.C. Chiaw, and I.E. Harik: Report No. KYSPR 00-215, KTC, University of Kentucky, Lexington, KY, 2003, pp. 1–25.
40. G.J. Kusinski and G. Thomas: Proc. 1st Int. Conf. Super High Strength Steels, AIM, Rome, Italy, 2005, CD.
41. J. Baczynski and J.J. Jonas: Acta Mater., 1996, vol. 44 (11), pp. 4273–88.10.1016/1359-6454(96)00114-0 ↗
42. F. Montheillet, M. Cohen, and J.J. Jonas: Acta Metall., 1984, vol. 32 (11), pp. 2077–89.10.1016/0001-6160(84)90187-1 ↗
43. S. Li, I.J. Beyerlein, and M.A. Bourke: Mater. Sci. Eng., A, 2005, vol. 394 (1–2), pp. 66–77.10.1016/j.msea.2004.11.032 ↗
44. G. Krauss: Steels: Processing, Structure, and Performance, ASM INTERNATIONAL, Materials Park, OH, 2005, pp. 55–59.