journal article·2015-05

Precipitation Behavior in the Heat-Affected Zone of Boron-Added 9Cr-3W-3Co Steel During Post-Weld Heat Treatment and Creep Deformation

Yuan Liu, Susumu Tsukamoto, Kota Sawada, Masaaki Tabuchi, Fujio Abe

Publisher page

Abstract

In the previous paper, we demonstrated that the addition of boron was effective in preventing type IV failure due to suppression of grain refinement in the heat-affected zone at the peak temperature of around AC3 (AC3 HAZ). However, some fine prior austenite grains (PAGs) still remained around the coarse PAG boundaries, and these fine PAGs may affect the creep property of the welded joint. In the present study, the effect of these fine PAGs on the creep property of the boron-added 9Cr-3Co-3W steel (B steel) Ac3 HAZ is investigated. Different heat treatments are carried out on B steel base metal to form different Ac3 HAZ-simulated microstructures of coarse PAG with and without fine PAGs. Ac3 HAZ microstructure shows that a lot of M23C6 carbides are formed at the block boundary in the interior of coarse PAG. On the other hand, few M23C6 carbides are formed at the fine PAG boundaries, but a number of μ phases (W6Fe7 type) cover the boundary. The formation of μ phase retards the recovery of dislocation at the fine PAG boundary and contributes to stabilizing the microstructure in the primary and transient creep regions. The μ phase transforms to the Laves phase during creep. As the growth rate of Laves phase is higher than that of M23C6 carbides during creep, the creep strength of fine PAG boundary, which is strengthened only by Laves phase, becomes a little bit lower than the other boundaries strengthened by M23C6 carbides after long-term creep. The mismatch of creep strength between the fine PAG boundary and the matrix should be taken into account to attain an excellent long-term creep property of the B steel welded joint.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Nuclear Materials and Properties · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. H. Hongo, M. Tabuchi and T. Watanabe: Metall. Mater. Trans. A, 2012, 43, 1163-1173.10.1007/s11661-011-0967-6 ↗
2. J. A. Francis, W. Mazur and H.K.D.H. Bhadeshia: Mater. Sci. Technol., 2006, 22, (12), 1387-1395.10.1179/174328406X148778 ↗
3. F. Abe and M. Tabuchi: Sci. Technol. Weld. Joining,, 2004, 9, (1), 22-29.10.1179/136217104225017107 ↗
4. M. Matsui, M. Tabuchi, T. Watanabe, K. Kubo, J. Kinugawa and F. Abe: ISIJ Inter., 2001, 41, S126-130.10.2355/isijinternational.41.Suppl_S126 ↗
5. D. Li, K. Shinozaki, H. Kuroki, H. Harada and K. Ohishi: Sci. Technol. Weld. Joining, 2003, 8, (4), 296-302.10.1179/136217103225005453 ↗
6. D. Li, K. Shinozaki, H. Kuroki, H. Harada and K. Ohishi: Metall. Mater. Trans. A, 2005, 36, 107-115.10.1007/s11661-005-0143-y ↗
7. Y. Liu, S. Tsukamoto, T.Shirane and F.Abe: Metall. Mater. Trans. A, 2013, 44, 4626-4633.10.1007/s11661-013-1801-0 ↗
8. S. Tsukamoto, Y. Liu, T. Shirane, M. Tabuchi and F. Abe: 9th Inter. Conf. Trends in welding Res., USA, June 2012.
9. T.Horiuchi, M.Igrashi and F.Abe: ISIJ Inter., 2002, 44, S67-71.10.2355/isijinternational.42.Suppl_S67 ↗
10. S. Albert, M. Kondo, M. Tabuchi, F. Yin, K. Sawada and F. Abe: Metall. Mater. Trans. A, 2005, 36, 333-343.10.1007/s11661-005-0306-x ↗
11. M. Kondo, M. Tabuchi, S. Tsukamoto, F. Yin and F. Abe: Sci. Technol. Weld. joining, 2006, 11, 216- 223.10.1179/174329306X89260 ↗
12. F. Abe, M. Tabuchi, M. Kondo and S. Tsukamoto: Inter. J. Pressure Vessels and Piping, 2007, 84, 44-52.10.1016/j.ijpvp.2006.09.013 ↗
13. T. Shirane, M. Shimizu, S. Tsukamoto, K. Tsuzaki, Y. Adachi, T. Hanamura, and F. Abe: Proc. 8th Intel. Conf. on Trends in Welding Res., Pine Mountain, GA, June 2008, pp. 284–91.
14. Y.Liu, S.Tsukamoto, K. Sawada, and F. Abe: Metall. Mater. Trans. A, DOI: 10.1007/s11661-013-2072-5.10.1007/s11661-013-2072-5 ↗
15. P. Mayr, I. Holzer, M. Albu, G. Kothleitner, H. Cerjak and S. Allen: 6th Int. Conf. on Adv. Mater. Technol. Fossil Power Plant, 2010, September, Santa Fe.
16. P. Mayr, C. Schlacher, S. Mitsche and C. Sommitsch: 4th Symposium on Heat Resistant Steels and Alloys Used for High Efficiency USC Power Plants, 2011, April, Beijing, China.
17. T. Hara, T. Tsuchiya, K. Tsuzaki, X. Man, T. Asahata and A.Umenoto: J. Alloy. Compound, 2013, 577S, S717-S721.10.1016/j.jallcom.2012.02.019 ↗
18. M. Igarashi and Y. Sawaragi: Proc. Inter. Conf. ‘Power Engineering-97’, 1997, July, Tokyo, Japan.
19. K. Kimura, K. Sawada, H. Kushima and K. Kubo: Inter. J. Mater. Res., 2008, 99, 395-401.10.3139/146.101651 ↗
20. F.Abe: Inter. Mater. Res., 2008, 99, 387-394.10.3139/146.101650 ↗
21. K.Kimura, K.Sawada, K.Kubo and H. Kushima: Proc. 2004 ASME/JSME PVP Conf., 2004, pp. 11–18.
22. F. Abe: Metall. Mater. Trans. A, 2005, 36A, 321-332.10.1007/s11661-005-0305-y ↗
23. J. S. Lee, H. G. Armaki, K. Maruyama, T. Muraki and H. Asahi: Mater. Sci. Eng. A, 2006, 428, 270-275.10.1016/j.msea.2006.05.010 ↗
24. H. Kushima, K. Kimura, and F. Abe: Tetsu to Hagane, 1999, vol. 85, pp. 841–47, In Japanese.10.2355/tetsutohagane1955.85.11_841 ↗
25. K. Suzuki, S. Kumai, H. Kushima, K. Kimura, and F. Abe: Tetsu to Hagane, 2003, vol. 89, pp. 691–98, In Japanese.10.2355/tetsutohagane1955.89.6_691 ↗