Primary creep behavior of Ti-48Al-2W as a function of stress and lamellar morphology
Source abstract
Abstract
The fully lamellar microstructure of powder metallurgy Ti-48Al-2W after cooling from the α region to 1280 °C, followed by air cooling and aging at 950 °C for up to 96 hours, is presented. Aging times as short as 5 hours result in acicular-shaped precipitates of W-rich β0 along lamellar interfaces, with the β0 size increasing with aging time. The β0 precipitates nucleate and grow in the α2 lamellae. Concurrently, with the formation of β0, the α2 decomposes into discontinuous lamellae. Aging to precipitate β0 along lamellar interfaces increases the 760 °C tensile strength (with a slight reduction of ductility) and reduces the instantaneous creep strain, since β0 precipitates at lamellar interfaces hinder interface dislocation mobility. The deformed microstructures from interrupted creep tests at 140 to 276 MPa at 760 °C indicate that the precipitation of β0 along interfaces substantially reduces the primary creep strain, primarily due to the influence of β0 on interface dislocation emission and motion. These results are discussed in terms of the influence of lamellar morphology on the instantaneous creep strain and primary creep transient, and the possible creep mechanisms are highlighted.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · MXene and MAX Phase Materials · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (53)
Show source-provided references
1. H.A. Lipsitt, D. Shechtman, and R.E. Schafrick: Metall. Trans. A, 1975, vol. 6A, p. 1991.10.1007/BF03161822 ↗
2. Y.-W. Kim: JOM, 1989, vol. 41 (7), p. 24.10.1007/BF03220267 ↗
3. Y.-W. Kim and F.H. Froes: in High Temperature Aluminides and Intermetallics, S.H. Whang, C.T. Liu, D.P. Pope, and J.O. Stiegler, eds., TMS, Warrendale, PA, 1990, pp. 465–92.
4. Y.-W. Kim and D.M. Dimiduk: JOM, 1991, vol. 43 (8), p. 40.10.1007/BF03221103 ↗
5. Y.-W. Kim: JOM. 1994, vol. 46 (7), pp. 30–39.10.1007/BF03220745 ↗
6. H.A. Lipsitt: in High-Temperature Ordered Intermetallic Alloys, C.C. Koch, C.T. Liu, and N.S. Stoloff, eds., Materials Research Society, Pittsburgh, PA, 1985, vol. 39, pp. 351–64.
7. C. Tönnes, J. Rösler, R. Baumann, and M. Thumann: in Structural Intermetallics, R. Darolia, J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, eds., TMS, Warrendale, PA, 1993, pp. 241–45.
8. J. Triantafillou, J. Beddoes, and W. Wallace: Can. Aeronautics Space J., 1996, vol. 42 (2), pp. 108–15.
9. M. Es-Souni, A. Bartels, and R. Wagner: Mater. Sci. Eng., 1995, vols. A192–A193, pp. 698–706.10.1016/0921-5093(94)03290-4 ↗
10. B.D. Worth, J.W. Jones, and J.E. Allison: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2947–59.10.1007/BF02669651 ↗
11. G.B. Viswanathan and V.K. Vasudevan: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 967–74.
12. S.W. Schwenker and Y.-W. Kim: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 985–92.
13. P.R. Bhowal, W.A. Konkel, and H.F. Merrick: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 787–94.
14. J. Beddoes, L. Zhao, P. Au, D. Dudzinski, and J. Triantafillou: in Structural Intermetallics 1997, M.V. Nathal, R. Darolia, C.T. Liu, P.L. Martin, D.B. Miracle, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1997, pp. 109–18.
15. K. Maruyama, R. Yamamoto, H. Nakakuki, and N. Fujitsuna: Mater. Sci. Eng., 1997, vols. A239–A240, p. 419.10.1016/S0921-5093(97)00612-6 ↗
16. P.D. Crofts, P. Bowen, and I.P. Jones: Scripta Mater., 1996, vol. 35, pp. 1391–96.10.1016/S1359-6462(96)00323-5 ↗
17. J. Beddoes, J. Triantafillou, and L. Zhao: High-Temperature Ordered Intermetallic Alloys VII, MRS 460, Boston, MA, 1997, C.C. Koch, C.T. Liu, N.S. Stoloff, and A. Wanner, eds., Materials Research Society, Pittsburgh, PA, 1997, pp. 293–98.
18. J.N. Wang, A.J. Schwartz, T.G. Nieh, C.T. Liu, V.K. Sikka, and D. Clemens: in Gamma Titanium Aluminides, Y.-W. Kim, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1995, pp. 949–57.
19. F. Herrouin, P. Bowen, and I.P. Jones: High-Temperature Ordered Intermetallic Alloys VII, MRS 460, Boston, MA, 1997, C.C. Koch, C.T. Liu, N.S. Stoloff, and A. Wanner, eds., Materials Research Society, Pittsburgh, PA, 1997, pp. 287–92.
20. K. Maruyama, R. Yamamoto, H. Nakakuki, and N. Fujitsuna: Mater. Sci. Eng., 1997, vols. A239–A240, pp. 419–28.10.1016/S0921-5093(97)00612-6 ↗
21. T.A. Parthasarathy, M. Keller, and M.G. Mendiratta: Scripta Mater., 1998, vol. 38, pp. 1025–31.10.1016/S1359-6462(98)00014-1 ↗
22. J.H. Yun, M.H. Oh, S.W. Nam, D.M. Wee, H. Inui, and M. Yamaguchi: Mater. Sci. Eng., 1997, vols. A239–A240, pp. 702–08.10.1016/S0921-5093(97)00655-2 ↗
23. J. Beddoes, L. Zhao, W.R. Chen, and X. Du: High Temperature Ordered Intermetallics VIII, MRS 552, Boston, MA, 1999, E.P. George, M.J. Mills, and M. Yamaguchi, eds., Materials Research Society, Pittsburgh, PA, 1999, pp. kk1.1.1-kk1.1.12.
24. G.B. Viswanathan, Y.-W. Kim, and M.J. Mills: in Gamma Titanium Aluminides 1999, Y.-W. Kim, D.M. Dimiduk, and M.H. Loretto, eds., TMS, Warrendale, PA, 1999, pp. 653–60.
25. F. Herrouin, D. Hu, P. Bowen, and I.P. Jones: Acta Mater., 1998, vol. 46, pp. 4963–72.10.1016/S1359-6454(98)00198-0 ↗
26. W.H. Tian and M. Nemoto: Intermetallics, 1997, vol. 5, pp. 237–44.10.1016/S0966-9795(96)00086-6 ↗
27. P.L. Martin and H.A. Lipsitt: Proc. 4th Int. Conf. Creep and Fracture of Engineering Materials and Structures, The Institute of Metals, London, 1990.
28. J. Beddoes, L. Zhao, and W. Wallace: Int. Mater. Rev., 1995, vol. 40 (5), pp. 197–217.10.1179/imr.1995.40.5.197 ↗
29. D.Y. Seo, J. Beddoes, L. Zhao, and G. Botton: Mater. Sci. Eng., 2002, vols. 329C–331C, pp. 810–20.10.1016/S0921-5093(01)01630-6 ↗
30. D.Y. Seo, T.R. Bieler, and D.E. Larsen: in Structural Intermetallics, M.V. Nathal, R. Darolia, C.T. Liu, P.L. Martin, D.B. Miracle, R. Wagner, and M. Yamaguchi, TMS, Warrendale, PA, 1997, p. 137.
31. D.Y. Seo, T.R. Bieler, and D.E. Larsen: in Advances in the Science and Technology of Titanium Alloy Processing, I. Weiss, R. Srinivasan, P. Bania, and D. Eylon, eds., TMS, Warrendale, PA, 1997, pp. 603–22.
32. D.Y. Seo, T.R. Bieler, and D.E. Larsen: Proc. 7th Int. Conf. on Creep and Fracture of Engineering Materials and Structures, Irvine, CA, Aug. 1997, p. 577.
33. D.Y. Seo, T.R. Bieler, and D.E. Larsen: Materials Research Society Symposia Proceedings, Materials Research Society, Pittsburgh, PA, 1997, p. 281.
34. D.Y. Seo, T.R. Bieler, S.U. An, and D.E. Larsen: Mater. Metall. Trans. A, 1998, vol. 29A, pp. 89–98.10.1007/s11661-998-0161-7 ↗
35. L.M. Hsiung and T.G. Nieh: Scripta Mater., 1997, vol. 36, p. 323.10.1016/S1359-6462(96)00380-6 ↗
36. J. Beddoes, D. Dudzinski, and L. Zhao: High Temp. Mater. Processing, 1999, vol. 18 (3), pp. 173–84.10.1515/HTMP.1999.18.3.173 ↗
37. M. Oehring, P.J. Ennis, F. Appel, and R. Wagner: High-Temperature Ordered Intermetallic Alloys VII, MRS 460, Boston, MA, 1999, C.C. Koch, C.T. Liu, N.S. Staloff, and A. Wanner, eds., Materials Research Society, Pittsburgh, PA, 1997, p. 257.
38. W. Wallace, L. Zhao, J. Beddoes, and D. Morphy: Hot Isostatic Pressing ’93, L. Delaey et al., eds., Elsevier Science, New York, NY, pp. 99–108.
39. Y. Zheng, L. Zhao, and K. Tangri: Scripta Metall., 1992, vol. 26, p. 291.10.1016/0956-716X(92)90189-L ↗
40. W.R. Chen: Ph.D. Thesis, Carleton University, Ottawa, 2000.
41. J. Beddoes, W.R. Chen, and L. Zhao: J. Mater. Sci., 2002, vol. 37, pp. 621–27.10.1023/A:1013786028136 ↗
42. R.W. Ramanujan, P.J. Maziasz, and C.T. Liu: Acta Mater., 1996, vol. 44, p. 2661.10.1016/1359-6454(95)00402-5 ↗
43. D.Y. Seo, J. Beddoes, and L. Zhao: 3rd Int. Symp. on Structural Intermetallics, Jackson Hole, WY, K.J. Hemker, D.M. Dimiduk, H. Clemens, R. Darolia, H. Innui, J.M. Larsen, V.K. Sikka, M. Thomas, and J.D. Whittenberger, eds., TMS, Warrendale, PA, Apr. 27–May 2, 2002, pp. 653–62.
44. J. Beddoes, D.Y. Seo, W.R. Chen, and L. Zhao: Intermetallics, 2001, vol. 9, pp. 915–22.10.1016/S0966-9795(01)00090-5 ↗
45. W.R. Chen, J. Beddoes, and L. Zhao: Mater. Sci. Engineer., 2002, vol. A323, pp. 306–17.10.1016/S0921-5093(01)01391-0 ↗
46. Y.-W. Kim: Intermetallics, 1998, vol. 6, p. 623.10.1016/S0966-9795(98)00037-5 ↗
47. G.B. Viswanathan, S. Karrikeyan, M.J. Mills, and V.K. Vasudevan: Mater. Sci. Eng., 2001, vols. A319–A321, pp. 833–37.10.1016/S0921-5093(01)01050-4 ↗
48. G.B. Viswanathan, R.W. Hayes, and M.J. Mills: Mater. Sci. Eng., 2001, vols. A319–A321, pp. 706–10.10.1016/S0921-5093(01)01048-6 ↗
49. L.M. Hsiung and T.G. Nieh: in Interstitial and Substitutional Solute Effects in Intermetallics, I. Baker, R.D. Nobeb, and E.P. George, eds., TMS, Warrendale, PA, 1993, p. 201.
50. S. Karrikeyan, G.B. Viswanathan, Y.W. Kim, V.K. Vasudevan, and M.J. Mills: 3rd Int. Symp. on Structural Intermetallics, Jackson Hole, WY, Apr. 27–May 2, 2002, pp. 717–23.
51. F. Appel and R. Wagner: Mater. Sci. Eng., 1998, vol. R22, pp. 221–26.
52. M. Oehring, F. Appel, P.J. Ennis, and R. Wagner: Intermetallics, 1999, vol. 7, pp. 355–45.10.1016/S0966-9795(98)00113-7 ↗
53. F. Appel: Intermetallics, 2001, vol. 9, pp. 907–14.10.1016/S0966-9795(01)00089-9 ↗