journal article·2006-10

Mechanical properties and deformation behavior of amorphous nickel-phosphorous films measured by nanoindentation test

Shou-Yi Chang, Yu-Shuien Lee, Hsiang-Long Hsiao, Ting-Kui Chang

Publisher page

Abstract

In this study, amorphous Ni-P films were deposited by electroless plating under different pH values. Their mechanical properties and deformation behavior were then investigated by instrumented nano-indentation. With increasing pH value of the plating solution from 3.75 to 6.0, the hardness and elastic modulus of the obtained Ni-P films increased from 6.1 GPa and 146 GPa to 8.2 GPa and 168 GPa respectively. From the load-indentation depth curve, the Ni-P films were found to yield at an indentation depth of 8 nm. By microstructural examination around the indented regions, early-stage plastic deformation of the amorphous Ni-P films was verified through the formation and extension of shear bands with a spacing of several tens of nanometers. Within the shear bands, flow dilatation-induced intense shear localization was expected and resulted in crystallization in the amorphous matrix. The critical shear stress and energy release rate required for the initiation of early-stage plastic yielding of the Ni-P films were calculated to be about 1.4 GPa and 3.0 J/m2 respectively, both of which increased with pH values.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Electrodeposition and Electroless Coatings · Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. L.F. Spencer: Metal. Finish., 1974, vol. 10, pp. 35–39.
2. G.O. Mallory and J.B. Hajdu: Electroless Plating: Fundamentals and Applications, American Electroplaters and Surface Finishers Society, Orlando, FL, 1990.
3. X. Li, B. Bhushan, K. Takashima, C.W. Baek, and Y.K. Kim: Ultramicroscopy, 2003, vol. 97, pp. 481–94.10.1016/S0304-3991(03)00077-9 ↗
4. W.S. Chung, S.Y. Chang, and S.J. Lin: Plat. Surf. Finish., 1996, vol. 83, pp. 68–71.
5. I. Apachitei, F.D. Tichelaar, J. Duszczyk, and L. Katgerman: Surf. Coat. Technol., 2001, vol. 148, pp. 284–95.10.1016/S0257-8972(01)01337-8 ↗
6. I. Apachitei, F.D. Tichelaar, J. Duszczyk, and L. Katgerman: Surf. Coat. Technol., 2002, vol. 149, pp. 263–78.10.1016/S0257-8972(01)01492-X ↗
7. S.K. Tien, J.G. Duh, and Y.I. Chen: Surf. Coat. Technol., 2004, vol. 177, pp. 532–36.10.1016/j.surfcoat.2003.08.032 ↗
8. S.K. Tien, J.G. Duh, and Y.I. Chen: Thin Solid Films, 2004, vol. 469, pp. 333–38.10.1016/j.tsf.2004.08.146 ↗
9. A. Inoue: Bulk Amorphous Alloys: Preparation and Fundamental Characteristics, Vol. 4, Materials Science Foundations, Trans. Tech. Publications, Netherlands, 1998.
10. P.E. Donovan: Acta Mater., 1989, vol. 37, pp. 445–56.10.1016/0001-6160(89)90228-9 ↗
11. P. Lowhaphandu, S.L. Montgomery, and J.J. Lewandowski: Scripta Mater., 1999, vol. 41, pp. 19–24.10.1016/S1359-6462(99)00128-1 ↗
12. J.G. Wang, B.W. Choi, T.G. Nieh, and C.T. Liu: J. Mater. Res., 2000, vol. 15, pp. 798–807.10.1557/JMR.2000.0114 ↗
13. R. Vaidyanathan, M. Dao, G. Ravichandran, and S. Suresh: Acta Mater., 2001, vol. 49, pp. 3781–89.10.1016/S1359-6454(01)00263-4 ↗
14. W.J. Wright, R. Saha, and W.D. Nix: Mater. Trans. Jpn. Inst. Mater., 2001, vol. 42, pp. 642–49.10.2320/matertrans.42.642 ↗
15. J.J. Kim, Y. Choi, S. Suresh, and A.S. Argon: Science, 2002, vol. 295, pp. 654–57.10.1126/science.1067453 ↗
16. G.P. Zhang, W. Wang, B. Zhang, J. Tan, and C.S. Liu: Scripta Mater., 2005, vol. 52, pp. 1147–51.10.1016/j.scriptamat.2005.01.045 ↗
17. C.A. Schuh and T.G. Nieh: J. Mater. Res., 2004, vol. 19, pp. 46–57.10.1557/jmr.2004.19.1.46 ↗
18. W.C. Oliver and G.M. Pharr: J. Mater. Res., 1992, vol. 7, pp. 1564–83.10.1557/JMR.1992.1564 ↗
19. A.C. Fischer-Cripps: Nanoindentation, Springer-Verlag, New York, 2002, pp. 1–173.10.1007/978-0-387-22462-6 ↗
20. A.E. Giannakopoulos and S. Suresh: Scripta Mater., 1999, vol. 40, pp. 1191–98.10.1016/S1359-6462(99)00011-1 ↗
21. E. Martinez, J. Romero, A. Lousa, and J. Esteven: Appl. Phys. A, 2003, vol. 77, pp. 419–27.10.1007/s00339-002-1669-0 ↗
22. S. Suresh, T.G. Nieh, and B.W. Choi: Scripta Mater., 1999, vol. 41, pp. 951–57.10.1016/S1359-6462(99)00245-6 ↗
23. A. Gouldstone, H.J. Koh, K.Y. Zeng, A.E. Giannakopoulos, and S. Suresh: Acta Mater., 2000, vol. 48, pp. 2277–99.10.1016/S1359-6454(00)00009-4 ↗
24. J. Chen, W. Wang, L.H. Qian, and K. Lu: Scripta Mater., 2003, vol. 49, pp. 645–50.10.1016/S1359-6462(03)00398-1 ↗
25. S.Y. Chang, T.Q. Chang, and Y.S. Lee: J. Electrochem. Soc., 2005, vol. 152, pp. C657–63.10.1149/1.2006508 ↗
26. B. Jackson, R. Macary, and G. Shawhan: Trans. Inst. Metal Finishing, 1990, vol. 68, pp. 75–83.10.1080/00202967.1990.11870871 ↗
27. K.L. Johnson: Contact Mechanics, Cambridge University Press, Cambridge, UK, 1985.10.1017/CBO9781139171731 ↗
28. T.H. Courtney: Mechanical Behavior of Materials, McGraw-Hill, New York, 1990, pp. 80–136, 263–324.
29. S.J. Bull and D.S. Rickerby: Surf. Coat. Technol., 1990, vol. 42, pp. 149–64.10.1016/0257-8972(90)90121-R ↗
30. S.J. Bull: Surf. Coat. Technol., 1991, vol. 50, pp. 25–32.10.1016/0257-8972(91)90188-3 ↗
31. S. Benayoun, L. Fouilland-Paillé, and J.J. Hantzpergue: Thin Solid Films, 1999, vol. 352, pp. 156–66.10.1016/S0040-6090(99)00319-3 ↗