journal article·2014-04

A Stacking Fault Energy Perspective into the Uniaxial Tensile Deformation Behavior and Microstructure of a Cr-Mn Austenitic Steel

H. Barman, A. S. Hamada, T. Sahu, B. Mahato, J. Talonen, S. K. Shee, P. Sahu, D. A. Porter, L. P. Karjalainen

Publisher page

Abstract

A Cr-Mn austenitic steel was tensile strained in the temperature range 273 K (0 °C) ≤ T ≤ 473 K (200 °C), to improve the understanding on the role of stacking fault energy (SFE) on the deformation behavior, associated microstructure, and mechanical properties of low-SFE alloys. The failed specimens were studied using X-ray diffraction, electron backscatter diffraction, and transmission electron microscopy. The SFE of the steel was estimated to vary between ~ 10 to 40 mJ/m2 at the lowest and highest deformation temperatures, respectively. At the ambient temperatures, the deformation involved martensite transformation (i.e., the TRIP effect), moderate deformation-induced twinning, and extended dislocations with wide stacking faults (SFs). The corresponding SF probability of austenite was very high (~10−2). Deformation twinning was most prevalent at 323 K (50 °C), also resulting in the highest uniform elongation at this temperature. Above 323 K (50 °C), the TRIP effect was suppressed and the incidence of twinning decreased due to increasing SFE. At elevated temperatures, fine nano-sized SF ribbons were observed and the SF probability decreased by an order (~10−3). High dislocation densities (~1015 m−2) in austenite were estimated in the entire deformation temperature range. Dislocations had an increasingly screw character up to 323 K (50 °C), thereafter becoming mainly edge. The estimated dislocation and twin densities were found to explain approximately the measured flow stress on the basis of the Taylor equation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. R.P.R. Kumtubarao: Int. Mater. Rev., 1989, vol. 34, pp. 69–86.10.1179/imr.1989.34.1.69 ↗
2. S. Curtze, V.-T. Kuokkala, A, Oikari, J. Talonen, and H. Hanninen: Acta Mater., 2011, vol. 59, pp. 1068–1076.10.1016/j.actamat.2010.10.037 ↗
3. M. Pozuelo, J.E. Wittig, J.A. Jiménez, G. Frommeyer: Metall. Mater. Trans. A, 2009, vol. 40, pp. 1826–1834.10.1007/s11661-009-9863-8 ↗
4. S. Allain, J.-P. Chateau, O. Bouaziz, S. Migot, N. Guelton: Mater. Sci. Eng. A, 2004, vols. 387–389, pp. 158–162.10.1016/j.msea.2004.01.059 ↗
5. A. Saeed-Akbari, L. Mosecker, A. Schwedt, W. Bleck: Metall. Mater. Trans. A, 2012, vol. 43A, pp. 1688–1704.10.1007/s11661-011-0993-4 ↗
6. G.B. Olson, M. Cohen: Metall. Trans., 1976, vol. 7A, pp. 1897–1904.
7. L. Rémy, A. Pineau: Mater. Sci. Eng., 1976, vol. 28, pp. 99–107.10.1016/0025-5416(77)90093-3 ↗
8. T.-H. Lee, E. Shin, C.-S. Oh, H.-Y. Ha, S.-J. Kim: Acta Mater, 2010, vol. 58, pp. 3173–3186.10.1016/j.actamat.2010.01.056 ↗
9. J.E. Wittig, M. Pozuelo, J.A. Jiménez, G. Frommeyer: Steel Res. Int., 2009, vol. 80, pp. 66–70.
10. A. Kovalev, A. Jahn, A. Weiß, P.R. Scheller: Steel Research Int., 2011, vol. 82, pp. 45–50.10.1002/srin.201000245 ↗
11. P. Sahu, S.K. Shee, A.S. Hamada, L. Rovatti, T. Sahu, B. Mahato, S. Ghosh Chowdhury, D.A. Porter, and L.P. Karjalainen: Acta Mater., 2012, vol. 60, pp. 6907–6919.10.1016/j.actamat.2012.07.055 ↗
12. A.S. Hamada, L.P. Karjalainen, R.D.K. Misra, J. Talonen: Mater. Sci. Eng. A, 2013, vol. 559, pp. 336–344.10.1016/j.msea.2012.08.108 ↗
13. B.E. Warren, B.L. Averbach: J. Appl. Phys., 1950, vol. 21, pp. 595–599.10.1063/1.1699713 ↗
14. H.M. Rietveld: J. Appl. Cryst., 1969, vol. 2, pp. 65–71.10.1107/S0021889869006558 ↗
15. T. Ungár, S. Ott, P. Sanders, A. Borbély, J.R. Weertman: Acta Mater., 1998, vol. 46, pp. 3693–3699.10.1016/S1359-6454(98)00001-9 ↗
16. R.J. Hill: in The Rietveld Method, Chapter 5, R.A. Young, ed., IUCr, Oxford University Press, Oxford, 1993.
17. L. Lutterotti: Materials Analysis Using Diffraction, version 2.33, 2011, http://www.ing.unitn.it/~maud/.
18. G. Caglioti, A. Paoletti, F.P. Ricci: Nucl. Inst. Methods, 1958, vol. 35, pp. 223– 228.10.1016/0369-643X(58)90029-X ↗
19. J.G.M. Van Berkum, G.J.M. Sprong, T.H. de Keijser, R. Delhez, and E.J. Sonneveld: Powder Diffr., 1995, vol. 10, pp. 129–139.10.1017/S0885715600014512 ↗
20. N.C. Popa,: J. Appl. Cryst., 1998, vol. 31, pp. 176–180.10.1107/S0021889897009795 ↗
21. E. Prince: in The Rietveld Method, Chapter 3, R.A. Young, ed., IUCr, Oxford University Press, Oxford, 1993.
22. B.E. Warren: X ray Diffraction, Addison-Wesley, Reading, 1969.
23. J. Talonen, H. Hanninen: Acta Mater., 2007, vol. 55, pp. 6108–6118.10.1016/j.actamat.2007.07.015 ↗
24. B.X. Huang, X.D. Huang, L. Wang, Y.H. Rong: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 717–724.10.1007/s11661-007-9434-9 ↗
25. R.E. Schramm, R.P. Reed: Metall. Trans. A, 1975, vol. 6, pp. 1345–1351.10.1007/BF02641927 ↗
26. M. Wilkens: Phys. Stat. Sol., 1970, vol. 2, pp. 359–370.10.1002/pssa.19700020224 ↗
27. M. Wilkens: in Fundamental Aspects of Dislocation Theory, J.A. Simmons, R. de Wit, and R. Bullougs, eds., NBS Spl Pub, II: 317, US Department of Commerce, Wasington, DC, 1970, p. 1195.
28. D.G. Brandon: Acta Metall., 1966, vol. 14, pp. 1479–1484.10.1016/0001-6160(66)90168-4 ↗
29. X.D. Wang, B.X. Huang, Y.H. Rong, L. Wang: J. Appl. Phys., 2007, vol. 101, pp. 093511–093515.10.1063/1.2655682 ↗
30. S. Martin, C. Ullrich, D. Šimek, U. Martin, D. Rafaja: J. Appl. Cryst., 2011, vol. 44, pp. 779–787.10.1107/S0021889811019558 ↗
31. M.S. Paterson: J. Appl. Phys., 1952, vol. 23, pp. 805–811.10.1063/1.1702312 ↗
32. T. Shintani, Y. Murata: Acta Mater., 2011, vol. 59, pp. 4314–4322.10.1016/j.actamat.2011.03.055 ↗
33. G.B. Olson, M. Azrin: Metall. Trans. A, 1978, vol. 9, pp. 713–721.10.1007/BF02659928 ↗
34. G.L. Huang, D.K. Matlock, G. Krauss: Met. Trans. A, 1989, vol. 20, pp. 1239– 1246.10.1007/BF02647406 ↗
35. G.E. Totten: in Chapter 6, Steel Heat Treatment: Metallurgy and Technologies, 2nd ed., Taylor and Francis, Boca Raton, 2007.10.1201/NOF0849384523 ↗
36. T.S. Byun: Acta Mater., 2003, vol. 51, pp. 3063–3071.10.1016/S1359-6454(03)00117-4 ↗
37. L. Velterop, R. Delhez, T.H. de Keijser, E.J. Mittemeijer, and D. Reefman: J. Appl. Cryst., 2000, vol. 33, pp. 296–306.10.1107/S0021889800000133 ↗
38. P.J. Schields, N. Dunwoody, M. Mamak, C. Gendron, S. Bates: Adv. X-ray Anal., 2007, vol. 53, pp. 162–168.
39. M.A. Meyers, O. Vöhringer, V.A. Lubarda: Acta Mater., 2001, vol. 49, pp. 4025– 4039.10.1016/S1359-6454(01)00300-7 ↗
40. R.L. Bell, R.W. Cahn: Proc. R. Soc. London A, 1957, vol. 239, pp. 494–521.10.1098/rspa.1957.0058 ↗
41. J.A. Venables: in Deformation Twinning, R.E. Reed-Hill, J.P. Hirth, and H.C. Rogers, eds., Gordon & Breach, New York, 1964.
42. R.E. Reed-Hill: Inhomogeneity of Plastic Deformation, ASM, Metals Park, OH, 1973.
43. S. Miura, J. Takamura, N. Narita: Supplement Trans. Japan Inst. Met., 1968, vol. 9, pp. 555–561.
44. W. Püschl: Prog. Mater. Sci., 2002, vol. 47, pp. 415–461.10.1016/S0079-6425(01)00003-2 ↗
45. M. Onyuna, H. Oettel, U. Martin, A. Weiß: Adv. Engg. Mater., 2004, vol. 6, pp. 529–535.10.1002/adem.200400411 ↗