Plastic straining effects on the microstructure of a Ti-rich NiTi shape memory alloy
Source abstract
Abstract
A Ni-52 at. pct Ti shape memory alloy, cold drawn to 30 pct, was annealed at 1173 K for 1 hour, water quenched, and then subjected to differential scanning calorimetry (DSC). No evidence of the premartensiticR transformation was found during either the forward or the reverse transformation. Microstructurally, it was found that the alloy possessed a relatively large volume fraction (∼0.05) of coarse second-phase brittle particles. These precipitates acted as preferential sites for martensite plate nucleation and gave rise to a “starlike” morphology. The tensile and compressive properties of the alloy in the as-received condition were also investigated. The alloy exhibited relatively good ductility (fracture strain=0.28), which was attributed to its inherent ability to relieve or delay the development of plastic instabilities through rapid strain hardening. In addition, X-ray diffraction (XRD) of deformed specimens indicated the presence of an extraintensity peak corresponding to the B2 phase (110)B2 when the alloy was plastically deformed in compression. Accordingly, it is suggested that plastic deformation induces the reverse transformation to the B2 phase in highly stressed local regions. Transmission electron microscopy (TEM) of deformed martensite structures showed slip lines probably due to dislocation slip, as well as variant interpenetration. Besides, optical and scanning microscopy of regions adjacent to the fractured surfaces indicated that fine martensite plates and/or “apparent” new grains develop at regions of prior stress intensification (former crack-tip regions) during crack propagation.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Shape Memory Alloy Transformations · Titanium Alloys Microstructure and Properties · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. P.A. Besselink:The Science and Technology of Shape Memory Alloys, Conf. Proc., Sec. V, University of Barcelona, Barcelona, 1989, p. 23.
2. K.N. Melton and O. Mercier:Acta Metall., 1981, vol. 29, p. 393.10.1016/0001-6160(81)90165-6 ↗
3. S. Miyazaki, Y. Igo, and K. Otsuka:Acta Metall., 1986, vol. 34, p. 2045.10.1016/0001-6160(86)90263-4 ↗
4. N.K. Melton:Engineering Aspects of Shape Memory Alloys, Editorial, Butterworth-Heinemann, Stoneham, MA, 1990, p. 21.10.1016/B978-0-7506-1009-4.50006-8 ↗
5. C.H. Lin and S.K. Wu:Acta Metall. Mater., 1994, vol. 42, p. 1623.10.1016/0956-7151(94)90371-9 ↗
6. S. Horibe and B. Iaird:Acta Metall., 1987, vol. 31, p. 1567.10.1016/0001-6160(83)90154-2 ↗
7. G. Rondelli, B. Vincentini, and A. Cigada A:Corrosion Properties of NiTi Shape Memory Alloys, MRS, Tokyo, 1988, p. 345.
8. C. Montero, H.F. Lopez, and A.J. Salinas:J. Biomed. Mater. Res., 1996, vol. 32, p. 583.10.1002/(SICI)1097-4636(199612)32:4<583::AID-JBM11>3.0.CO;2-F ↗
9. D.F. Williams:Compatibility of Clinical Implant Materials, CRC editorial, CRC, Boca Raton, FL, 1981, vol. 1, p. 129.
10. L.S. Castleman, S.M. Motzkin, F.P. Alicandri, and V.L. Bonawit:J. Biomed. Mater. Res., 1976, vol. 10, p. 695.10.1002/jbm.820100505 ↗
11. D.N. Abujudom, P.E. Thoma, and S. Fariabi:Mater. Sci Forum, 1990, vol. 56, p. 565.10.4028/www.scientific.net/MSF.56-58.565 ↗
12. Y. Liu and P.G. McCormick:Acta Metall. Mater., 1994, vol. 42, p. 2401.10.1016/0956-7151(94)90318-2 ↗
13. P.G. McCormick and Y. Liu:Acta Metall. Mater., 1994, vol. 42, p. 2407.10.1016/0956-7151(94)90319-0 ↗
14. Y. Liu and P.G. McCormick:Acta Metall. Mater., 1990, vol. 38, p. 1321.10.1016/0956-7151(90)90204-T ↗
15. P.G. Lindquist and C.M. Wayman: inEngineering Aspects of Shape Memory Alloys, T.W. Deurig, K.N. Melton, D. Stöckel, and C.W. Wayman, eds., Editorial, Butterworth-Heinemann, Stoneham, MA, 1990, p. 58.10.1016/B978-0-7506-1009-4.50009-3 ↗
16. R.J. Wasilewski, S.R. Butler, J.E. Hanlon, and D. Worden:Metall. Trans. A, 1971, vol. 2, pp. 229–38.10.1007/BF02662662 ↗
17. M. Nishida, C.M. Wayman, and T. Honma:Metall. Trans. A, 1986, vol. 17A, pp. 1505–15.10.1007/BF02650086 ↗
18. D. Stroz, J. Kwarciak, and H. Morawiec:J. Mater. Sci., 1988, vol. 23, p. 4127.10.1007/BF01106847 ↗
19. H.F. Lopez, R.A. Salinas, and J.L.G. Rodriguez:Scripta Mater., 1996, vol. 34, p. 659.10.1016/1359-6462(95)00570-6 ↗
20. G. Chattopadhayay and H. Kleykamp:Z. Metalkd., 1983, vol. 74, p. 182.
21. Y. Liu, Z.L. Xie, J.V. Humbeeck, and L. Delaey:Acta Mater., 1999, vol. 47, p. 645.10.1016/S1359-6454(98)00376-0 ↗
22. Y. Liu, Y. Liu, J.V. Humbeeck:Acta Mater., 1999, vol. 47, pp. 199–209.10.1016/S1359-6454(98)00325-5 ↗
23. Z. Xie, Y. Liu, and V. Humbeeck:Acta Mater., 1998, vol. 46, pp. 1989–2000.10.1016/S1359-6454(97)00379-0 ↗
24. J. Ortin and A. Planes:Acta Metall., 1988, vol. 36, p. 1873.10.1016/0001-6160(88)90291-X ↗
25. P.G. Lindquist and C.M. Wayman: inEngineering Aspects of Shape Memory Alloys, T.W. Dueriget al., eds., Editorial, Butterworth-Heinemann, Stoneam, MA, 1990, p. 22.
26. K. Gall, H. Sehitoglu, Y.I. Chumlyakov, and I.V. Kireeva:Acta Mater., 1990, vol. 47, pp. 1203–17.10.1016/S1359-6454(98)00432-7 ↗
27. T. Saburi and S. Nenno:Proc. Int. Conf. on Solid to Solid Phase Transitions, ASM, Metals Park, OH, 1982, p. 1455.
28. L. Xie, Y. Liu, Z.J.V. Humbeeck, and L. Delaey:Acta Mater., 1998, vol. 46, p. 4325.10.1016/S1359-6454(97)00379-0 ↗
29. H. Sehitoglu, I. Karaman, R. Anderson, X. Zhang, K. Gall, H.J. Maier, and Y. Chumlyakov:Acta Mater., 2000, vol. 48, pp. 3311–26.10.1016/S1359-6454(00)00153-1 ↗
30. H.C. Lin, S.K. Wu, T.S. Chou, and H.P. Kao:Acta Metall. Mater., 1991, vol. 39, p. 2069.10.1016/0956-7151(91)90177-3 ↗
31. H.C. Lin and S.K. Wu:Metall. Trans. A, 1993, vol. 24A, pp. 293–99.10.1007/BF02657316 ↗
32. J.P. Bressanelli and A. Moskowitz:Trans. ASM, 1966, vol. 59, p. 223.
33. E. Hornbogen:Acta Metall., 1978, vol. 26, p. 147.10.1016/0001-6160(78)90211-0 ↗
34. D.L. Porter and A.H. Heuer:J. Am. Ceram. Soc., 1977, vol. 60, p. 183.10.1111/j.1151-2916.1977.tb15509.x ↗
35. A.A. Bulbich:J. Mater. Sci., 1992, vol. 27, p. 1070.10.1007/BF01197662 ↗
36. A.A. Bulbich and P. Toledano:Phys. Rev. Lett., 1998, vol. 81, p. 838.10.1103/PhysRevLett.81.838 ↗