journal article·2001-05

The evolution of grain boundary character during superplastic deformation of an Al-6 pct Cu-0.4 pct Zr alloy

M. Eddahbi, O. A. Ruano, T. R. McNelley

Publisher page

Abstract

The evolution of microstructure, texture, and microtexture in an Al-6 pct Cu-0.4 pct Zr alloy was studied during mechanical testing at 480 °C and a strain rate of 5·10−4 s−1. The as-processed material had an elongated, banded microstructure and a deformation texture with orientation distribution along the β-orientation fiber. The true strain vs true stress curve exhibited three stages: I, II, and III. Work hardening occurred in stages I and III, whereas nearly steady-state behavior was observed in stage II. A bimodal distribution of boundary disorientation angles was evident in as-processed material and persisted into stage I, with peaks at 5–15 deg in the low-angle boundary (LAB) regime and at 45–60 deg in the high-angle boundary (HAB) regime. An increase in strain rate sensitivity coefficient, m, in stage I was accompanied by fragmentation of the initial microstructure, leading to the formation of new grains. During stage II the strain rate sensitivity coefficient, m, attained a value of 0.5, which is consistent with the onset of grain boundary sliding. In stage III, the texture and the grain boundary disorientation distribution became randomized while the m value decreased. Grain elongation and cavity formation at second-phase particles and along grain boundaries were seen in samples deformed to failure. The as-processed microstructure is described in terms of deformation banding, and a model for the evolution of such a structure during superplastic deformation is proposed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Metallurgy and Material Forming · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. N. Ridley: Superplasticity: 60 Years after Pearson, The Institute of Materials, London, 1995.
2. G.S. Sohal: Mater. Sci. Technol., 1988, vol. 4, pp. 811–15.10.1179/mst.1988.4.9.811 ↗
3. K.A. Padmanabhan, J. Hirsh, and K. Lücke: J. Mater. Sci., 1991, vol. 26, pp. 5301–08.10.1007/BF01143225 ↗
4. V. Randle: Acta Metall., 1995, vol. 43, pp. 1741–49.10.1016/0956-7151(94)00414-D ↗
5. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Pergamon Press, Oxford, United Kingdom, 1995, pp. 235–79.
6. N. Ridley: Mater. Sci. Technol., 1990, vol. 6, pp. 1145–56.10.1179/mst.1990.6.11.1145 ↗
7. M.T. Perez-Prado: Ph.D. Thesis, Universidad Complutense de Madrid, Madrid, Spain, 1998.
8. T.G. Langdon: Acta Metall. Mater., 1994, vol. 42, pp. 2437–43.10.1016/0956-7151(94)90322-0 ↗
9. T.R. McNelley, E.-W. Lee, and M.E. Mills: Metall. Trans. A, 1986, vol. 17A, pp. 1035–41.10.1007/BF02661269 ↗
10. M.T. Lyttle and J.A. Wert: J. Mater. Sci., 1994, vol. 29, pp. 3342–50.10.1007/BF00356683 ↗
11. H. Ahlborn, E. Hornbogen, and U. Köster: J. Met. Sci., 1965, vol. 4, pp. 944–50.10.1007/BF00555308 ↗
12. B.M. Watts, M.J. Stowell, B.L. Baikie, and D.G.E. Owen: Met. Sci., 1976, vol. 10, pp. 198–06.
13. B.M. Watts, M.J. Stowell, B.L. Baikie, and D.G.E. Owen: Met. Sci., 1976, vol. 10, pp. 189–97.10.1016/0036-9748(76)90147-2 ↗
14. R.H. Johnson, C.M. Parker, L. Anderson, and O.D. Sherby: Phil. Mag., 1968, vol. 18, p. 1309.10.1080/14786436808227761 ↗
15. N. Naziri and R. Pearce: J. Inst. Met., 1970, vol. 98, p. 71.
16. K.N. Melton, J.W. Edington, J.S. Kallend, and C.P. Cutler: Acta Metall., 1974, vol. 22, pp. 165–70.10.1016/0001-6160(74)90006-6 ↗
17. K.N. Melton and J.W. Edington: Scripta Metall., 1974, vol. 8, p. 1141.10.1016/0036-9748(74)90484-0 ↗
18. C.P. Cutler, J.W. Edington, J.S. Kallend, and K.N. Melton: Acta Metall., 1974, vol. 22, pp. 665–71.10.1016/0001-6160(74)90164-3 ↗
19. L.C.A. Samuelsson, K.N. Melton, and J.W. Edington: Acta Metall., 1976, vol. 24, pp. 1017–26.10.1016/0001-6160(76)90132-2 ↗
20. J.W. Edington K.N. Melton, and C.P. Cutler: Progr. Mater. Sci., 1976, vol. 21, pp. 63–170.10.1016/0079-6425(76)90005-0 ↗
21. K. Matsuki, H. Morita, M. Yamada, and Y. Murakami: Met. Sci., 1977, vol. 11, pp. 156–63.10.1179/msc.1977.11.5.156 ↗
22. O.A. Kaibyshev, B.V. Rodionov, and R.Z. Valiev: Acta Metall., 1978, vol. 26, pp. 1877–86.10.1016/0001-6160(78)90100-1 ↗
23. R.H. Bricknell and J.W. Edington: Acta Metall., 1979, vol. 27, pp. 1303–10.10.1016/0001-6160(79)90199-8 ↗
24. R.H. Bricknell and J.W. Edington: Metall. Trans., 1979, vol. 10, pp. 1257–63.10.1007/BF02811981 ↗
25. R.H. Bricknell and J.W. Edington: Acta Metall., 1979, vol. 27, pp. 1313–18.10.1016/0001-6160(79)90200-1 ↗
26. O.A. Kaibyshev, I.V. Kazachkov, and R.M. Galeev: J. Mater. Sci., 1981, vol. 16, p. 2501.10.1007/BF01113587 ↗
27. P.L. Blackwell and P.S. Bate: Superplasticity: 60 Years after Pearson, N. Ridley, eds., The Institute of Materials, Manchester, United Kingdom, 1994, pp. 183–92.
28. B.P. Kashyap, A. Arieli, and A.K. Mukherje: J. Mater. Sci., 1985, vol. 20, pp. 2661–86.10.1007/BF00553028 ↗
29. L.K.L. Falk, P.R. Howell, G.L. Dunlop, and T.G. Langdon: Acta Metall., 1986, vol. 4, pp. 1203–14.10.1016/0001-6160(86)90007-6 ↗
30. L. Qing, H. Xiaoxu, Y. Mei, and Y. Jinfeng: Acta Metall., 1992, vol. 40, pp. 1753–62.10.1016/0956-7151(92)90118-X ↗
31. P.S. Bate: Metall. Trans. A, 1992, vol. 23A, pp. 1467–78.10.1007/BF02647330 ↗
32. P.L. Blackwell and P.S. Bate: Metall. Trans. A, 1993, vol. 24A, pp. 1085–93.10.1007/BF02657239 ↗
33. J. Liu and D.J. Chakrabarti: Acta Metall., 1996, vol. 44, pp. 4647–61.
34. M.T. Pérez-Prado, M.C. Cristina, O.A. Ruano, and G. González-Doncel: Mater. Sci. Eng., 1998, vol. 244, pp. 216–23.10.1016/S0921-5093(97)00567-4 ↗
35. M.T. Pérez-Prado, T.R. McNelley, O.A. Ruano, and G. González-Doncel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 485–92.10.1007/s11661-998-0129-7 ↗
36. E. Hornbogen: Metall. Trans. A, 1979, vol. 10A, pp. 947–72.10.1007/BF02811643 ↗
37. E. Nes: Int. Conf. on Superplasticity, B. Baudelet and M. Suéry, eds., CNRS, Grenoble, 1985, pp. 7.1–7.14.
38. H. Gudmudsson, D. Brooks, and J.A. Wert: Acta Metall., 1991, vol. 39, pp. 19–35.10.1016/0956-7151(91)90325-U ↗
39. S.J. Hales, T.R. McNelley, and H.J. McQueen: Metall. Trans. A, 1991, vol. 22A, pp. 1037–47.10.1007/BF02661097 ↗
40. M.T. Lyttle and J.A. Wert: J. Mater. Sci., 1994, vol. 29, pp. 3342–50.10.1007/BF00356683 ↗
41. K. Tsuzaki, H. Xiaoxu, and T. Maki: Acta Mater., 1996, vol. 44, pp. 4491–99.10.1016/1359-6454(96)00080-8 ↗
42. R.D. Doherty, D.A. Hughes, F.J. Humphreys, J.J. Jonas, D.J. Jensen, M.E. Kassner, W.E. King, T.R. McNelley, H.J. McQueen, and A.D. Rollett: Mater. Sci. Eng., 1997, vol. 238, pp. 219–74.10.1016/S0921-5093(97)00424-3 ↗
43. T.R. McNelley, M.E. McMahon, and M.T. Pérez-Prado: Phil. Trans. A, 1999, vol. 357A, pp. 1683–05.10.1098/rsta.1999.0396 ↗
44. O.A. Ruano, M.T. Perez-Prado, G. Gonzalez-Doncel, and T.R. McNelley: Creep Behavior of Advanced Materials for the 21st Century, TMS, Warrendale, PA, 1999, p. 333.
45. M. Eddahbi: Ph.D. Thesis, Universidad Complutense de Madrid, Madrid, 1998.
46. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 4231–40.10.1016/S1359-6454(97)00070-0 ↗
47. F.J. Humphreys: Acta Mater., 1997, vol. 45, pp. 5031–39.10.1016/S1359-6454(97)00173-0 ↗
48. E. Nes: Met. Sci., 1979, vol. 13, pp. 211–15.10.1016/0036-9748(79)90296-5 ↗
49. H. Bunge: Texture Analysis in Materials Science, Butterworth and Co., London, 1982.
50. V. Randle: Microtexture Determination and Its Applications, The Institute of Materials, London, 1992.
51. T.R. McNelley and M.E. McMahon: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 2252–62.10.1007/BF02651879 ↗
52. T.R. McNelley and M.E. McMahon: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1879–87.10.1007/s11661-997-0118-2 ↗
53. S.R. Skjervold and N. Ryum: Acta Metall., 1995, vol. 43 (8), pp. 3159–76.10.1016/0956-7151(95)00008-J ↗
54. V. Randle and D. Dingley: Acta Metall., 1988, vol. 36 (2), pp. 267–73.10.1016/0001-6160(88)90003-X ↗
55. V. Randle: Acta Metall., 1995, vol. 43 (5), pp. 1741–49.10.1016/0956-7151(94)00414-D ↗
56. J.K. Mackenzie: Biometrica, 1958, vol. 45, pp. 229–40.10.1093/biomet/45.1-2.229 ↗
57. D.A. Hughes and N. Hansen: Acta Metall., 1997, vol. 45, pp. 3871–86.
58. C.S. Barrett: Trans. Am. Inst. Min. Eng., 1939, vol. 135, p. 296.
59. C.S. Barrett and H. Levenson: Trans. Am. Inst. Min. Eng., 1940, vol. 137, p. 327.
60. C.S. Lee and B.J. Duggan: Acta Metall. Mater., 1993, vol. 41, pp. 2691–99.10.1016/0956-7151(93)90138-I ↗
61. C.S. Lee, B.J. Duggan, and R.E. Smallman: Acta Metall. Mater., 1993, vol. 41, pp. 2265–70.10.1016/0956-7151(93)90308-F ↗
62. K. Kulkarni, E.A. Starke, Jr., and D. Kuhlmann-Wilsdorf: Acta Mater., 1998, vol. 46, pp. 5283–01.10.1016/S1359-6454(98)00225-0 ↗
63. M.T. Pérez-Prado and T.R. McNelley: Scripta Mater., 1999, vol. 40, pp. 1401–06.10.1016/S1359-6462(99)00096-2 ↗
64. J. Hirsh and K. Lücke: Acta Metall., 1988, vol. 36, pp. 2883–04.10.1016/0001-6160(88)90173-3 ↗
65. S.J. Hales and T.R. McNelley: Acta Metall., 1988, vol. 36, pp. 1229–39.10.1016/0001-6160(88)90275-1 ↗
66. K. Matsuki, T. Iwaki, M. Tokizawa, and Y. Murakami: Mater. Sci. Technol., 1991, vol. 7, pp. 513–19.10.1179/mst.1991.7.6.513 ↗
67. T.R. McNelley, M.E. McMahon, and S.J. Hales: Scripta Mater., 1997, vol. 36, pp. 369–75.10.1016/S1359-6462(96)00403-4 ↗