Empirical Approach to Understanding the Fatigue Behavior of Metals Made Using Additive Manufacturing
Source abstract
Abstract
High-cycle fatigue measurements were performed on alloys prepared by powder-bed fusion additive manufacturing techniques. Selective laser melted (SLM) nickel-based superalloy 625 and electron beam melted (EBM) Ti-6Al-4V specimens were prepared as round fatigue specimens and tested with as-built surfaces at stress ratios of −1, 0.1 and 0.5. Data collected at R = −1 were used to construct Goodman diagrams that correspond closely to measured experimental data collected at R > 0. A second way to interpret the HCF data is based on the influence of surface roughness on fatigue, and approximate the surface feature size as a notch. On this basis, the data were interpreted using the fatigue notch factor kf and average stress models relating kf and stress concentration factor Kt. The depth and root radius of surface features associated with fatigue crack initiation were used to estimate a Kt of 2.8 for SLM 625. For Ti-6Al-4V, a direct estimate of Kt from HCF data was not possible, but approximate values of kf based on HCF data and Kt from crack initiation site geometry are found to explain other published EBM Ti-6Al-4V.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. MIL-HDBK-5, United States Department of Defense, Washington, DC, 2003.
2. MMPDS, United States Federal Aviation Administration, Battelle Institute, 2015.
3. L. Robinson and J. Scott: JOM, 2014, Vol. 66, pp. 2194–2204.10.1007/s11837-014-1166-x ↗
4. J. Halchak, J. Wooten and B. McEnerney: 12th World Conference on Titanium, Beijing, 2011, p. 1715.
5. E. M. Betts, D. E. Eddleman, D. C. Reynolds and N. A. Hardin: JANNAF 6th Liquid Propulsion Subcommittee Meeting, Huntsville, Alabama, 2011.
6. C. Qiu, C. Panwisawas, M. Ward, H. C. Basoalto, J. W. Brooks and M. M. Attallah: Acta Mater., 2015, vol. 96, p. 72.10.1016/j.actamat.2015.06.004 ↗
7. K. A. Mumtaz and N. Hopkinson: J. Mat. Proc. Tech., 2010, vol. 210, p. 279.10.1016/j.jmatprotec.2009.09.011 ↗
8. B. Van Hooreweder, R. Boonen, D. Moens, J.-P. Kruth and P. Sas: AIAA/ASME/ASCE/AHS/ASC 53rd Conf. Struct. Struc. Dyn. Mat., 2012, p. 1733.
9. K. S. Chan, M. Koike, R. L. Mason and T. Okabe: Metall. Mater. Trans. A, 2013, vol. 43, p. 1010.10.1007/s11661-012-1470-4 ↗
10. P. Edwards and M. Ramulu: Mat. Sci. Eng. A, 2014, vol. 586, p. 327.10.1016/j.msea.2014.01.041 ↗
11. H. K. Rafi, N. V. Karthik, H. Gong, T. L. Starr and B. E. Stucker: J. Mat. Eng. Perf., 2013, vol. 22, p. 3872.10.1007/s11665-013-0658-0 ↗
12. K. D. Redekal, M.S. Thesis, Air Force Inst. Tech., 2015.
13. D. Greitemeier, C. Dalle Donne, F. Syassen, J. Eufinger and T. Melz: Mat. Sci. Tech., 2015, in press, doi:10.1179/1743284715Y.0000000053.10.1179/1743284715Y.0000000053 ↗
14. P. Edwards, A. O’Connor and M. Ramulu: ASME J. Man. Science Eng., 2013, vol. 135, p. 061016-1.10.1115/1.4025773 ↗
15. D. B. Witkin, P. Adams and T. V. Albright: Proc. SPIE Laser 3D Manufacturing II, 2015, vol. 9353, p. 93530B-1.10.1117/12.2083699 ↗
16. D. Arola and C. L. Williams: Int. J. Fat., 2002, vol. 24, p. 923.10.1016/S0142-1123(02)00012-9 ↗
17. E466-07, ASTM, West Conshohocken, Penn., 2007.
18. E8-11, ASTM, West Conshohocken, 2011.
19. S. L. Lu, H. P. Tang, Y. P. Ning, N. Liu, D. H. St. John and M. Qian: Metall. Mat. Trans. A, 2015, vol. 46, p. 3824.10.1007/s11661-015-2976-3 ↗
20. S. S. Al-Bermani, M. L. Blackmore, W. Zhang and I. Todd: Metall. Mat. Trans. A, 2010, vol. 41, p. 3422.10.1007/s11661-010-0397-x ↗
21. L. Thijs, F. Verhaeghe, T. Craeghs, J. Van Humbeeck and J.-P. Kruth: Acta Mat., 2010, vol. 58, p. 3303.10.1016/j.actamat.2010.02.004 ↗
22. B. Vrancken, L. Thijs, J.-P. Kruth and J. Van Humbeeck: J. Alloys Comp, 2012, vol. 541, pp. 177.10.1016/j.jallcom.2012.07.022 ↗
23. C. Qiu, N. J. E. Adkins and M. M. Attallah: Mat. Sci. Eng. A, 2013, vol. 578, p. 230.10.1016/j.msea.2013.04.099 ↗
24. L. Ladani: Metall. Mat. Trans. A, 2015, vol. 46, p. 3835.10.1007/s11661-015-2965-6 ↗
25. P. A. Kobryn and S. L. Semiatin: J. Mat. Proc.Tech., 2003, vol. 135, p. 330.10.1016/S0924-0136(02)00865-8 ↗
26. B. E. Carroll, T. A. Palmer and A. M. Beese: Acta Mater., 2015, vol. 87, p. 309.10.1016/j.actamat.2014.12.054 ↗
27. L. E. Murr, S. A. Quinones, S. M. Gaytan, M. I. Lopez, A. Rodela, E. Y. Martinez, D. H. Hernandez, E. Martinez, F. Medina and R. B. Wicker: J. Mech. Behavior Biomed. Mat., 2009, vol. 2, p. 20.10.1016/j.jmbbm.2008.05.004 ↗
28. L. E. Murr, E. Martinez, S. M. Gaytan, D. A. Ramirez, B. I. Machado, P. W. Shindo, J. L. Martinez, F. Medina, J. Wooten, D. Ciscel, U. Ackelid and R. B. Wicker: Metall. Mat. Trans. A, 2011, vol. 32, p. 3491.10.1007/s11661-011-0748-2 ↗
29. S. Floreen, G. E. Fuchs and W. J. Yang E. A. Loria: Superalloys,1994, p. 13–37.10.7449/1994/Superalloys_1994_13_37 ↗
30. M. J. Cieslak, T. J. Headley, T. Kollie and J. A. D. Romig: Metall. Mat. Trans A, 1988, vol. 19, p. 2319.10.1007/BF02645056 ↗
31. F. Cortial, J. M. Corrieu and C. Vernot-Loier: Metall. Mat. Trans A, 1995, vol. 26, p. 1273.10.1007/BF02670621 ↗
32. P. Ganesh, R. Kaul, C. P. Paul, P. Tiwari, S. K. Rai, R. C. Prasad and L. M. Kukreja: Mat. Sci. Eng. A, 2010, vol. 527, p. 7490.10.1016/j.msea.2010.08.034 ↗
33. G. Puppula, A. Moitra, S. Sathyanarayanan, R. Kaul, G. Sasikala, R. C. Prasad and L. M. Kukreja: Materials and Design, 2014, vol. 59, p. 509-515.10.1016/j.matdes.2014.03.013 ↗
34. S. Leuders, M. Thone, A. Riemer, T. Niendorf, T. Troster, H. A. Richard and H. J. Maier: Int. J. Fat., 2013, vol. 48, p. 300.10.1016/j.ijfatigue.2012.11.011 ↗
35. S. Leuders, T. Lieneke, S. Lammers, T. Troster and T. Niendorf: J. Mat. Res., 2014, vol. 29, p. 1911.10.1557/jmr.2014.157 ↗
36. D. Eylon and C. M. Pierce: Metall. Trans. A, 1976, vol. 7A, p. 111.10.1007/BF02644046 ↗
37. J. A. Hines and G. Lutjering: Fat. Frac. Eng. Mat. Struc., 1999, vol. 22, p. 657.10.1046/j.1460-2695.1999.t01-1-00217.x ↗
38. S. Suresh: Fatigue of Materials, Cambridge University Press, Cambridge, United Kingdom, 1998.10.1017/CBO9780511806575 ↗
39. T. Nicholas and J. R. Zuiker: Int. J.Frac., 1996, vol. 80, p. 219.10.1007/BF00012670 ↗
40. R. K. Nalla, B. L. Boyce, J. L. Campbell, J. O. Peters and R. O. Ritchie: Metall. Mat. Trans. A, 2002, vol. 33A, p. 899.10.1007/s11661-002-0160-z ↗
41. S. G. Ivanova, R. R. Biederman and R. D. Sisson: J. Mat. Eng. Perf., 2002, vol. 11, p. 226.10.1361/105994902770344312 ↗
42. J. Lindemann and L. Wagner: Mat. Sci. Eng. A, 1997, vol. 234-236, p. 1118.10.1016/S0921-5093(97)00347-X ↗
43. T. Nicholas: High Cycle Fatigue—A Mechanics of Materials Perspective, Elsevier Amsterdam, 2006.
44. W. D. Pilkey and D. F. Pilkey: Peterson’s Stress Concentration Factors, John Wiley, Hoboken, N.J., 2008, p. 522.
45. M. Peters, A. Gysler and G. Lutjering: Metall. Trans. A, 1984, vol. 15, p. 1597.10.1007/BF02657799 ↗
46. B. Oberwinkler, A. Lettner and W. Eichlseder: Int. J. Fat., 2011, vol. 33, p. 710.10.1016/j.ijfatigue.2010.11.024 ↗