journal article·2010-04

Mechanical Behavior and Microstructural Change of a High Nitrogen CrMn Austenitic Stainless Steel during Hot Deformation

Zhenhua Wang, Wantang Fu, Shuhua Sun, Hui Li, Zhiqing Lv, Deli Zhao

Publisher page

Abstract

The hot deformation behavior of a high nitrogen CrMn austenitic stainless steel in the temperature range 1173 to 1473 K (900 to 1200 °C) and strain rate range 0.01 to 10 s−1 was investigated using optical microscopy, stress-strain curve analysis, processing maps, etc. The results showed that the work hardening rate and flow stress decreased with increasing deformation temperature and decreasing strain rate in 18Mn18Cr0.5N steel. The dynamic recrystallization (DRX) grain size decreased with increasing Z value; however, deformation heating has an effect on the DRX grain size under high strain rate conditions. In the processing maps, flow instability was observed at higher strain rate regions (1 to 10 s−1) and manifested as flow localization near the grain boundary. Early in the deformation, the flow instability region was at higher temperatures, and then the extent of this unstable region decreased with increasing strain and was restricted to lower temperatures. The hot deformation equation as well as the quantitative dependence of the critical stress for DRX and DRX grain size on Z value was obtained.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. M.O. Speidel: High Nitrogen Steel 1988 Conf., J. Foct and A. Hendry, eds., Institute of Metals, London, 1989, pp. 92–99.
2. J. Menzel, G. Stein, and P. Dahlmann: High-Nitrogen Steels ’90, Proc. 3rd Int. Conf. on High Nitrogen Steel, G. Stein and H. Witulski, eds., Verlag Stahleisen mbH, Dusseldorf, 1990, pp. 365–71.
3. V.G. Gavriljuk: ISIJ Int., 1996, vol. 36, pp. 738–45.10.2355/isijinternational.36.738 ↗
4. J.W. Simmons: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2579–95.10.1007/BF02669416 ↗
5. D. Jandová, J. Řehoř, and Z. Nový: J. Mater. Process. Technol., 2004, vols. 157–158, pp. 523–30.10.1016/j.jmatprotec.2004.09.072 ↗
6. W.T. Fu, Z. Wang, and W.C. Liu: Iron Steel, 1998, vol. 33, pp. 45–48 (in Chinese).
7. W.T. Fu, Y.Z. Zheng, and X.K. He: Wear, 2001, vol. 249, pp. 788–91.10.1016/S0043-1648(01)00811-0 ↗
8. W.C. Liu, Y.Z. Zheng, and M.Z. Wang: Iron Steel, 1994, vol. 29 (7), pp. 55–57 (in Chinese).
9. G.Z. Cui, D.F. Gao, and J.Z. Cai: J. Plasticity Eng., 1996, vol. 3, pp. 3–6 (in Chinese).
10. C.Y. Wang, X.J. Wang, and H. Chang: Mater. Sci. Eng. A, 2007, vol. 464, pp. 52–58.10.1016/j.msea.2007.03.003 ↗
11. S.S. Menon and H.J. Rack: Mater. Sci. Eng. A, 2001, vol. 297, pp. 244–55.10.1016/S0921-5093(00)01008-X ↗
12. N.K. Park, J.T. Yeom, and Y.S. Na: J. Mater. Process. Technol., 2002, vols. 130–131, pp. 540–45.10.1016/S0924-0136(02)00801-4 ↗
13. Y.V.R.K. Prasad, S. Sasidhara, and V.K. Sikka: Intermetallics, 2000, vol. 8, pp. 987–95.10.1016/S0966-9795(00)00048-0 ↗
14. S. Venugopal, P.V. Sivaprasad, and M. Vasudevan: J. Mater. Process. Technol., 1995, vol. 59, pp. 343–50.10.1016/0924-0136(95)02160-4 ↗
15. J.T. Liu, H.B. Chang, and R.H. Wu: Mater. Charact., 2000, vol. 45, pp. 175–86.10.1016/S1044-5803(00)00071-1 ↗
16. C.M. Sellars: Yue Sed Proc. Int. Conf. on Mathematical Modelling of Hot Rolling of Steel, CIMM, Hamilton, ON, Canada, 1900, pp. 1–18.
17. Y.H. Lu, R.D. Fu, and L. Qiu: Trans. Mater. Heat Treatment, 2007, vol. 28, pp. 69–72 (in Chinese).
18. S.F. Medina and C.A. Hernandez: Acta Mater., 1996, vol. 44, pp. 137–48.10.1016/1359-6454(95)00151-0 ↗
19. E.I. Poliak and J.J. Jonas: ISIJ Int., 2003, vol. 43, pp. 684–91.10.2355/isijinternational.43.684 ↗
20. A. Najafizadeh and J.J. Jonas: ISIJ Int., 2006, vol. 46, pp. 1679–84.10.2355/isijinternational.46.1679 ↗
21. D. Ponge and G. Gottstein: Acta Mater., 1998, vol. 46, pp. 69–80.10.1016/S1359-6454(97)00233-4 ↗
22. S.I. Kim and Y.C. Yoo: Mater. Sci. Eng. A, 2001, vol. 311, pp. 108–13.10.1016/S0921-5093(01)00917-0 ↗
23. Y.V.R.K. Prasad and S. Sasidhara: Hot Working Guide: A Compendium of Processing Maps, ASM, Materials Park, OH, 1997, pp. 3–8.
24. M. Jafari and A. Najafizadeh: Mater. Sci. Eng. A, 2009, vol. 501, pp. 16–25.10.1016/j.msea.2008.09.073 ↗