Dynamic recrystallization of ferrite in a low-carbon steel
Source abstract
Abstract
Plane strain compression tests were performed on a low-carbon steel from 550 °C to 700 °C (ferritephase range) at strain rates of 10 to 5 × 10−4 s−1, and the deformation microstructure evolution was investigated by means of scanning electron microscopy, transmission electron microscopy (TEM), and electron backscattered diffraction (EBSD). The results indicate that under the present deformation conditions, dynamic recrystallization of ferrite can occur in the low-carbon steel and lead to grain refinement. With increasing Zener-Hollomon parameter Z, the mechanism of this process changes from discontinuous dynamic recrystallization to continuous dynamic recrystallization; the turning point is approximately at Z=1 × 1016 s−1. The increase of parameter Z leads to the decrease of recrystallized grain size of ferrite under steady state of deformation, and can lead to the formation of ultrafine microstructures with average grain size of about 2 µm.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (15)
Show source-provided references
1. M.R. Barnett and J.J. Jonas: Iron Steel Inst. Jpn. Int., 1999, vol. 39, pp. 856–73.10.2355/isijinternational.39.856 ↗
2. G. Glover and C.M. Sellars: Metall. Trans., 1973, vol. 4, pp. 765–75.10.1007/BF02643086 ↗
3. G. Glover and C.M. Sellars: Metall. Trans., 1972, vol. 3, pp. 2271–80.10.1007/BF02643242 ↗
4. N. Tsuji, Y. Matsubara, and Y. Saito: Scripta Mater., 1997, vol. 37, pp. 477–84.10.1016/S1359-6462(97)00123-1 ↗
5. A. Najafi-Zadeh, J.J. Jonas, and S. Yue: Metall. Trans. A, 1992, vol. 23A, pp. 2607–17.10.1007/BF02658064 ↗
6. P.R. Cetlin, S. Yue, and J.J. Jonas: Iron Steel Inst. Jpn. Int., 1993, vol. 33, pp. 488–97.10.2355/isijinternational.33.488 ↗
7. A. Belyakov, R. Kaibyshev, and R. Zaripova: Mater. Sci. Forum, 1993, vols. 113–115, pp. 385–89.10.4028/www.scientific.net/MSF.113-115.385 ↗
8. F. Gao, Y. Xu, B. Song, and K. Xia: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 21–27.10.1007/s11661-000-0048-8 ↗
9. H. Yagi, N. Tsuji, and Y. Saito: Tetsu-to-Hagané, 2000, vol. 86, pp. 349–56.10.2355/tetsutohagane1955.86.5_349 ↗
10. S. Gohda, K. Watanabe, and Y. Hashimoto: Trans. Iron Steel Inst. Jpn., 1981, vol. 21, pp. 6–15.10.2355/isijinternational1966.21.6 ↗
11. R.Z. Wang and T.C. Lei: Scripta Metall. Mater., 1993, vol. 28, pp. 629–32.10.1016/0956-716X(93)90208-A ↗
12. R.Z. Wang and T.C. Lei: Scripta Metall. Mater., 1994, vol. 31, pp. 1193–96.10.1016/0956-716X(94)90575-4 ↗
13. Z.Q. Sun, W.Y. Yang, J.J. Qi, and A.M. Hu: Mater. Sci. Eng. A, 2002, vol. 334A, pp. 201–06.10.1016/S0921-5093(01)01806-8 ↗
14. A. Belyakov, H. Miura, and T. Sakai: Mater. Sci. Eng. A, 1998, vol. 255A, pp. 139–47.10.1016/S0921-5093(98)00784-9 ↗
15. I. Tamura: Tetsu-to-Hagané, 1988, vol. 74, pp. 18–35.10.2355/tetsutohagane1955.74.1_18 ↗