Interplay Between Residual Stresses, Microstructure, Process Variables and Engine Block Casting Integrity
Source abstract
Abstract
The replacement of nodular cast iron with 319 type aluminum (Al) alloys in gasoline engine blocks is an example of the shift towards the use of lighter alloys in the automotive industry. However, excessive residual stress along the cylinder bore may lead to bore distortion, significantly reducing engine operating efficiency. In the current study, microstructure, mechanical properties and residual stress were characterized along the cylinder bridge of engine blocks following thermal sand reclamation (TSR), T7 heat treatment, and service testing of the casting. Neutron diffraction was effectively used to quantify the residual stress along both the Al cylinder bridge and the adjacent gray cast iron cylinder liners in the hoop, radial, and axial orientations with respect to the cylinder axis. The results suggest that an increase in cooling rate along the cylinder caused a significant refinement in microstructure at the bottom of the cylinder. In turn, this suggested an increase in alloy strength at the bottom of the cylinder relative to the top. This increased strength at the bottom of the cylinder likely reduced the susceptibility of the cylinder to rapid relief of residual stress at elevated temperature. In contrast, the coarse microstructure at the top of the cylinder likely triggered stress relief at an elevated temperature.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. J.R. Davis: ASM Specialty Handbook: Aluminum and Aluminum Alloys, ASM International, Materials Park, OH, 1993.
2. Y. Ling, Z. Xu, and C. Defrancq: 2 nd International Aluminum Casting Technology Symposium, 2002, Columbus, OH, pp. 117–20.
3. M.J. Moran and H.N. Shapiro: Fundamentals of Engineering Thermodynamics, 5th ed., Wiley, New York, NY, 2004, pp. 401–04.
4. X. Su, J. Jan, J. Lasecki, and J. Allison: 1 st International Symposium on Metallurgical Modelling for Aluminum Alloys, Pittsburgh, PA, 2003, pp. 63–68.
5. E. Carrera, A. Rodriguez, J. Talamantes, S. Valtierra, and R. Colas: J. Mater. Process. Technol., 2007, vol. 189, pp. 206–10.10.1016/j.jmatprotec.2007.01.023 ↗
6. M. Li, R. Vijayaraghavan, C. Wolverton, and J. Allison: 1 st International Symposium on Metallurgical Modelling for Aluminum Alloys, Pittsburgh, PA, 2003, pp. 79–86.
7. M. Tiryakioglu and G.E. Totten: Heat Treating: Proceedings of the 18 th Conference, Rosemont, IL, 1998, pp. 156–65.
8. A. Lombardi, F. D’Elia, A. Machin, C. Ravindran, and R. MacKay: AFS Trans., 2011, vol. 119, pp. 229–38.
9. M. Flemings: Solidification Processing, McGraw-Hill College, New York, NY, 1974.10.1007/BF02643923 ↗
10. R. Torres, J. Esparza, E. Velasco, S. Garcia-Luna, and R. Colas: Int. J. Microstruct. Mater. Properties, 2006, vol. 1, pp. 129–38.10.1504/IJMMP.2006.010621 ↗
11. A. Lombardi, F. D’Elia, C. Ravindran, B.S. Murty, and R. MacKay: Trans. Indian Inst. Met., 2011, vol. 64, pp. 7–11.10.1007/s12666-011-0002-z ↗
12. Z. Li, A.M. Samuel, F.H. Samuel, C. Ravindran, and S. Valtierra: J. Mater. Sci., 2003, vol. 38, pp. 1203–18.10.1023/A:1022857703995 ↗
13. A.M. Samuel, J. Gauthier, and F.H. Samuel: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 1785–98.10.1007/BF02651928 ↗
14. G. Garcia-Garcia, J. Espinoza-Cuadra, and H. Mancha-Molinar: Mater. Des., 2007, vol. 28, pp. 428–33.10.1016/j.matdes.2005.09.021 ↗
15. J. Hwang, R. Banerjee, H.W. Doty, and M. Kaufman: Acta Mater., 2009, vol. 57, pp. 1308–17.10.1016/j.actamat.2008.11.021 ↗
16. D. Porter and K. Easterling: Phase Transformations in Metals and Alloys, 2nd ed., Chapman & Hall, London, U.K., 1992.10.1007/978-1-4899-3051-4 ↗
17. F.J. Tavitas-Medrano, S. Valtierra, J.E. Gruzleski, F.H. Samuel, and H.W. Doty: AFS Trans., 2008, vol. 116, pp. 99–114.
18. B. Skrotzki, G.J. Shiflet, and E.A. Starke: Metall. Mater. Trans. A., 1996, vol. 27A, pp. 3431–44.10.1007/BF02595436 ↗
19. G.E. Deiter: Mechanical Metallurgy, 2nd ed., McGraw-Hill International, London, U.K., 1981, pp. 211–19.
20. G.E. Totten: Handbook of Residual Stress and Deformation of Steel, ASM International, Materials Park, OH, 2002, pp. 89–91.
21. J.S. Robinson and D.A. Tanner: Mater. Sci. Forum, 2002, vols. 404–407, pp. 355–60.10.4028/www.scientific.net/MSF.404-407.355 ↗
22. J.S. Robinson and D.A. Tanner: Mater. Sci. Technol., 2003, vol. 19, pp. 512–18.10.1179/026708303225001939 ↗
23. J.S. Robinson, D.A. Tanner, C.E. Truman, and R.C. Wimpory: Exp. Mech., 2011, vol. 51, pp. 981–93.10.1007/s11340-010-9389-4 ↗
24. D. Sediako, A. Lombardi, F. D’Elia, C. Ravindran, A. Machin, R.B. Rogge, and R. MacKay: COM 2011 Conference Proceedings, Montreal, QC, Canada, 2011.