journal article·2004-03

High-strain-rate superplastic behavior of equal-channel angular-pressed 5083 Al-0.2 wt pct Sc

Dong Hyuk Shin, Duck-Young Hwang, Yong-Jun Oh, Kyung-Tae Park

Publisher page

Abstract

Tensile tests were carried out at temperatures of 673 to 773 K and strain rates of 1×10−3 to 1 s−1 on an ultrafine-grained (UFG) 5083 Al alloy containing 0.2 wt pct Sc fabricated by equal-channel angular pressing, in order to examine its high-strain-rate superplastic characteristics. The mechanical data for the alloy at 723 and 773 K exhibited a sigmoidal behavior in a double logarithmic plot of the maximum true stress vs true strain rate. The strain-rate sensitivity was 0.25 to 0.3 in the low-( $$\dot \varepsilon $$ <5×10−3 s−1) and high- ( $$\dot \varepsilon $$ >5×10−2 s−1) strain-rate regions, and ∼0.5 in the intermediate-strain-rate region (5×10−3 s−1< $$\dot \varepsilon $$ <5 × 10−2 s−1). The maximum elongation to failure of ∼740 pct was obtained at 1×10−2 s−1 and 773 K. By contrast, no sigmoidal behavior was observed at 673 K. Instead, the strain-rate sensitivity of 0.3 was measured in both intermediate-and low-strain-rate regions, but it was about 0.25 in the high-strain-rate region. High-strain-rate superplasticity (HSRS) in the intermediate-strain-rate region at 723 and 773 K was dominated by grain-boundary sliding (GBS) associated with continuous recrystallization and preservation of fine recrystallized grains by second-phase particles. However, the activation energy for HSRS of the present alloy was lower than that predicted for any standard high-temperature deformation mechanism. The low activation energy was likely the result of the not-fully equilibrated microstructure due to the prior severe plastic deformation (SPD). For 673 K, the mechanical data and the microstructural examination revealed that viscous glide was a dominant deformation mechanism in the intermediate- and low-strain-rate regions. Deformation in the high-strain-rate region at all testing temperatures was attributed to dislocation breakaway from solute atmospheres.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. Z. Horita, M. Furukawa, M. Nemoto, A.J. Barnes, and T.G. Langdon: Acta Mater., 2000, vol. 48, pp. 3633–40.10.1016/S1359-6454(00)00182-8 ↗
2. I.C. Hisao and J.C. Huang: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 1373–84.10.1007/s11661-002-0062-0 ↗
3. K.-T. Park, D.Y. Hwang, S.Y. Chang, and D.H. Shin: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2859–67.10.1007/s11661-002-0271-6 ↗
4. R.Z. Valiev, D.A. Salimonenko, N.K. Tsenev, P.B. Berbon, and T.G. Langdon: Scripta Mater., 1997, vol. 37, pp. 1945–50.10.1016/S1359-6462(97)00387-4 ↗
5. I.C. Hisao and J.C. Huang: Scripta Mater., 1999, vol. 40, pp. 697–703.10.1016/S1359-6462(98)00460-6 ↗
6. R.R. Sawtell and C.L. Jensen: Metall. Trans. A, 1990, vol. 21A, pp. 421–30.10.1007/BF02782422 ↗
7. T.G. Nieh, R. Kaibyshev, L.M. Hsiung, N. Nguyen, and J. Wadsworth: Scripta Mater., 1997, vol. 36, pp. 1011–16.10.1016/S1359-6462(96)00479-4 ↗
8. T.G. Nieh, L.M. Hsiung, J. Wadsworth, and R. Kaibyshev: Acta Mater., 1998, vol. 46, pp. 2789–2800.10.1016/S1359-6454(97)00452-7 ↗
9. S. Lee, A. Utsunomiya, H. Akamatsu, K. Neishi, M. Furukawa, Z. Horita, and T.G. Langdon: Acta Mater., 2002, vol. 50, pp. 553–64.10.1016/S1359-6454(01)00368-8 ↗
10. M. Furukawa, A. Utsunomiya, K. Matsubara, Z. Horita, and T.G. Langdon: Acta Mater., 2001, vol. 49, pp. 3829–38.10.1016/S1359-6454(01)00262-2 ↗
11. S. Komura, Z. Horita, M. Furukawa, M. Nemoto, and T.G. Langdon: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 707–16.10.1007/s11661-001-0087-9 ↗
12. H. Akamatsu, T. Fujinami, Z. Horita, and T.G. Langdon: Scripta Mater., 2001, vol. 44, pp. 759–64.10.1016/S1359-6462(00)00666-7 ↗
13. K.-T. Park, D.Y. Hwang, Y.K. Lee, Y.K. Kim, and D.H. Shin: Mater. Sci. Eng., 2003, vol. A341, pp. 273–81.10.1016/S0921-5093(02)00216-2 ↗
14. M. Furukawa, P.B. Berbon, Z. Horita, M. Nemoto, N.K. Tsenev, R.Z. Valiev, and T.G. Langdon: Mater. Sci. Forum, 1997, vols. 233–234, pp. 177–84.10.4028/www.scientific.net/MSF.233-234.177 ↗
15. V.M. Segal, V.I. Reznikov, A.D. Drobyshevsky, and V.I. Kopylov: Russ. Metall., 1981, vol. 1, pp. 99–105.
16. V.M. Segal: Mater. Sci. Eng., 1995, vol. A197, pp. 157–64.10.1016/0921-5093(95)09705-8 ↗
17. M. Nemoto, Z. Horita, M. Furukawa, and T.G. Langdon: Met. Mater. Int., 1998, vol. 4, pp. 1181–90.10.1007/BF03025992 ↗
18. S. Komura, M. Furukawa, Z. Horita, M. Nemoto, and T.G. Langdon: Mater. Sci. Eng., 2001, vol. A297, pp. 111–18.10.1016/S0921-5093(00)01255-7 ↗
19. P.A. Friedman and A.K. Ghosh: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3030–42.10.1007/BF02663852 ↗
20. D.H. Bae and A.K. Ghosh: Acta Mater., 2000, vol. 48, pp. 1207–24.10.1016/S1359-6454(99)00445-0 ↗
21. R.S. Mishra, R.Z. Valiev, S.X. McFadden, R.K. Islamgaliev, and A.K. Mukherjee: Phil. Mag. A, 2001, vol. 81, pp. 37–48.10.1080/014186101300012390 ↗
22. J.W. Edington: Practical Electron Microscopy in Materials Science IV: Typical Electron Microscope Investigation, Philips, Eindhoven, 1976, pp. 9–15.
23. R. Verma, A.K. Ghosh, S. Kim, and C. Kim: Mater. Sci. Eng., 1995, vol. A191, pp. 143–50.10.1016/0921-5093(94)09644-9 ↗
24. F.A. Mohamed and T.G. Langdon: Phys. Status Solidi, 1976, vol. 33, pp. 375–81.10.1002/pssa.2210330140 ↗
25. F.A. Mohamed, S. Shei, and T.G. Langdon: Acta Metall., 1975, vol. 23, pp. 1443–50.10.1016/0001-6160(75)90153-4 ↗
26. J.E. Bird, A.K. Mukherjee, and J.E. Dorn: in Quantitative Relation between Properties and Microstructures, D.G. Brandon and A. Rosen, eds., Israel University Press, Jerusalem, 1969, p. 255.
27. F.J. Humphreys and M. Hatherly: Recrystallization and Related Annealing Phenomena, Pergamon Press, Oxford, United Kingdom, 1995, p. 92.
28. O.D. Sherby and P.M. Burke: Progr. Mater. Sci., 1967, vol. 13, pp. 325–90.
29. S.J. Rothman, N.L. Peterson, L.J. Nowicki, and L.L. Robinson: Phys. Status Solidi (b), 1974, vol. 63, pp. K29-K33.10.1002/pssb.2220630151 ↗
30. P. Yavari and T.G. Langdon: Acta Metall., 1982, vol. 30, pp. 2182–96.
31. F.A. Mohamed: Mater. Sci. Eng., 1998, vol. A245, pp. 242–56.10.1016/S0921-5093(97)00725-9 ↗
32. J. Friedel: Dislocations, Pergamon, Oxford, United Kingdom, 1964, pp. 351–67.10.1016/B978-0-08-013523-6.50018-1 ↗
33. J.T. Evans: Scripta Metall., 1987, vol. 21, pp. 1435–38.10.1016/0036-9748(87)90278-X ↗
34. N. Behnood and J.T. Evans: Acta Metall., 1989, vol. 37, pp. 687–95.10.1016/0001-6160(89)90252-6 ↗
35. T.R. McNelley, E.-W. Lee, and M.E. Mills: Metall. Trans. A, 1986, vol. 17A, pp. 1035–41.10.1007/BF02661269 ↗
36. S.X. McFadden, R.S. Mishra, R.Z. Valiev, A.P. Zhilyaev, and A.K. Mukherjee: Nature, 1999, vol. 398, pp. 684–86.10.1038/19486 ↗
37. Y.R. Kolobov, G.P. Grabovetskaya, M.B. Ivanov, A.P. Zhilyaev, and R.Z. Valiev: Scripta Mater., 2001, vol. 44, pp. 873–78.10.1016/S1359-6462(00)00699-0 ↗
38. P.K. Chaudhury and F.A. Mohamed: Acta Metall., 1988, vol. 36, pp. 1099–110.10.1016/0001-6160(88)90163-0 ↗
39. G. Rai and N.J. Grant: Metall. Trans. A, 1973, vol. 6A, pp. 385–90.
40. F.A. Mohamed and T.G. Langdon: Phil. Mag., 1975, vol. 32, pp. 687–709.10.1080/14786437508221614 ↗
41. F.A. Mohamed: J. Mater. Sci., 1983, vol. 18, pp. 582–92.10.1007/BF00560647 ↗
42. R.W. Lund and W.D. Nix: Acta Metall., 1976, vol. 24, pp. 469–79.10.1016/0001-6160(76)90068-7 ↗
43. W.C. Oliver and W.D. Nix: Acta Metall., 1982, vol. 30, pp. 1335–47.10.1016/0001-6160(82)90153-5 ↗
44. F.A. Mohamed, K.-T. Park and E.J. Lavernia: Mater. Sci. Eng., 1992, vol. A150, pp. 21–35.10.1016/0921-5093(90)90004-M ↗
45. P. Málek and M. Cieslar: Mater. Sci. Eng., 1997, vols. A234–A236, pp. 782–85.10.1016/S0921-5093(97)00318-3 ↗
46. D.H. Shin, K.-T. Park, and E.J. Lavernia: Mater. Sci. Eng., 1995, vol. 201, pp. 118–26.10.1016/0921-5093(95)09761-9 ↗
47. S.S. Woo, Y.R. Kim, D.H. Shin, and W.J. Kim: Scripta Mater., 1997, vol. 37, pp. 1351–58.10.1016/S1359-6462(97)00275-3 ↗
48. E.M. Taleff, G.A. Henshall, T.G. Nieh, D.R. Lesuer, and J. Wadsworth: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1081–91.10.1007/s11661-998-0300-1 ↗
49. E.W. Hart: Acta Metall., 1967, vol. 15, pp. 351–55.10.1016/0001-6160(67)90211-8 ↗
50. F.A. Mohamed: Scripta Metall., 1979, vol. 13, pp. 87–90.10.1016/0036-9748(79)90041-3 ↗
51. T.H. Lin, J.P. Hirth, and E.W. Hart: Acta Metall., 1981, vol. 29, pp. 819–27.10.1016/0001-6160(81)90124-3 ↗
52. P.K. Koenig and F.A. Mohamed: Mater. Sci. Eng., 1985, vol. 72, pp. L9-L11.10.1016/0025-5416(85)90076-X ↗
53. M. Mostafa and F.A. Mohamed: Metall. Trans. A, 1986, vol. 17A, pp. 365–66.10.1007/BF02643918 ↗
54. E. Taleff, D.R. Lesuer, and J. Wadsworth: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 343–52.10.1007/BF02648411 ↗