journal article·2011-06

The Effect of Friction Stir Processing on the Mechanical Properties of Investment Cast and Hot Isostatically Pressed Ti-6Al-4V

A. L. Pilchak, J. C. Williams

Publisher page

Abstract

Friction-stir (FS) processing was used to modify the coarse, fully lamellar microstructure of investment cast and hot isostatically pressed (HIP’ed) Ti-6Al-4V. The effect of FS processing on mechanical properties was investigated using microtensile and four-point bend fatigue testing. The tensile results showed a typical microstructure dependence where yield strength and ultimate tensile strength both increased with decreasing slip length. Depending on the processing parameters, fatigue strength at 107 cycles was increased by 20 pct or 60 pct over that of the investment cast and HIP’ed base material. These improvements have been verified with a statistically significant number of tests. The results have been discussed in terms of the resistance of each microstructure fatigue crack initiation and small crack propagation. For comparison, a limited number of fatigue tests was performed on α + β forged Ti-6Al-4V with varying primary α volume fraction and also on investment cast material heat treated to produce a bi-lamellar condition.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. R.S. Mishra, M.W. Mahoney, S.X. McFadden, N.A. Mara, and A.K. Mukherjee: Scripta Mater., 2000, vol. 42, pp. 163-688.10.1016/S1359-6462(99)00329-2 ↗
2. A.L. Pilchak, Z.T. Li, J.J. Fisher, A.P. Reynolds, M.C. Juhas, and J.C. Williams: in Friction Stir Welding and Processing IV, R.S. Mishra, M.W. Mahoney, T.J. Lienert, and K.V. Jata, eds., TMS, Warrendale, PA, 2007, pp. 419–27.
3. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Proc. 11th World Ti 2007 Conf., M. Ninomi, S. Akiyama, M. Ikeda, M. Hagiwara, and K. Maruyama, eds., Kyoto, Japan, 2007, pp. 1723-26.
4. M.C. Juhas, G.B. Viswanathan, and H.L. Fraser: Proc. of the Second Symp. Friction Stir Welding, Gothenburg, Sweden, 2000, CD Proceedings.
5. T.J. Lienert, K.V. Jata, R. Wheeler, and V. Seetharaman: Proc. Joining of Advanced and Specialty Materials III, ASM International, Materials Park, OH, 2001, pp. 160-66.
6. N. Karogal: Master’s Thesis, The Ohio State University, Columbus, OH, 2002.
7. A.J. Ramirez and M.C. Juhas: Mater. Sci. Forum, 2003, vols. 426-432, pp. 2999-3004.10.4028/www.scientific.net/MSF.426-432.2999 ↗
8. W.-B. Lee, C.-Y. Lee, W.-S. Chang, Y.-M. Yeon, and S.-B. Jung: Mater. Lett., 2005, vol. 59, pp. 3315-18.10.1016/j.matlet.2005.05.064 ↗
9. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Metall. Mater. Trans. A, 2007, vol. 38A, pp. 401-08.10.1007/s11661-006-9061-x ↗
10. A.L. Pilchak, M.C. Juhas, and J.C. Williams: Welding in the World, 2008, vol. 52 (9/10) – Research Supplement IIW-1888-08.10.1007/BF03266670 ↗
11. S. Mironov, Y. Zhang, Y.S. Sato, and H. Kokawa: Scripta Mater., 2008, vol. 59, pp. 27-30.10.1016/j.scriptamat.2008.02.014 ↗
12. S. Mironov, Y. Zhang, Y.S. Sato, and H. Kokawa: Scripta Mater., 2008, vol. 59, pp. 511-14.10.1016/j.scriptamat.2008.04.038 ↗
13. Y. Zhang, Y.S. Sato, H. Kokawa, S.H.C. Park, and S. Hirano: Mater. Sci. Eng. A, 2008, vol. 485, pp. 448-55.10.1016/j.msea.2007.08.051 ↗
14. K.E. Knipling and R.W. Fonda: Scripta Mater., 2009, vol. 60, pp. 1097-1100.10.1016/j.scriptamat.2009.02.050 ↗
15. L. Zhou, H.J. Liu, P. Liu, and Q.W. Liu: Scripta Mater., 2009, vol. 61, no. 6, pp. 596-99.10.1016/j.scriptamat.2009.05.029 ↗
16. A.L. Pilchak and J.C. Williams: Metall. Mater. Trans. A, DOI:10.1007/s11661-010-0434-9.10.1007/s11661-010-0434-9 ↗
17. D.A. LaVan and W.N. Sharpe, Jr.: Exp. Mech., 1999, vol. 39 no. 3, pp. 210-16.10.1007/BF02323554 ↗
18. K.J. Hemker and W.N. Sharpe, Jr.: Annu. Rev. Mater. Res., 2007, vol. 37, pp. 93-126.10.1146/annurev.matsci.36.062705.134551 ↗
19. G. Wegmann, J. Albrecht, G. Lütjering, K.-D. Folkers, and C. Liesner: Z. Fur Metallkd, 1997, vol. 88, no. 10, pp. 764-73.
20. J.C. Chesnutt, A.W. Thompson, and J.C. Williams: Influence of Metallurgical Factors on the Fatigue Crack Growth Rate in Alpha-Beta Titanium Alloys, Final Technical Report AFML-TR-78-68, Air Force Research Laboratory.
21. T. Zhai, Y.G. Xu, J.W. Martin, A.J. Wilkinson, and G.A.D. Briggs: Int. J. Fatigue, 1999, vol. 21, pp. 889-94.10.1016/S0142-1123(99)00084-5 ↗
22. A.L. Pilchak and R.E.A. Williams: The Ohio State University, unpublished research, 2008.
23. W.G. Burgers: Physica, 1934, vol. 1, pp. 561-86.10.1016/S0031-8914(34)80244-3 ↗
24. A.L. Pilchak, W. Tang, H. Sahiner, A.P. Reynolds, and J.C. Williams: Metall. Mater. Trans. A, DOI:10.1007/s11661-010-0439-9.10.1007/s11661-010-0439-9 ↗
25. Y.E. Beygelzimer and A.V. Spuskanyuk: Phil. Mag. A, 1999, vol. 79, pp. 2437-59.10.1080/01418619908214293 ↗
26. D.M. Norfleet: Ph.D. Dissertation, The Ohio State University, Columbus, OH, 2007.
27. J.C. Williams, R.G. Baggerly, and N.E. Paton: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 837-50.10.1007/s11661-002-0153-y ↗
28. A.L. Pilchak: Ph.D. Dissertation, The Ohio State University, Columbus, OH, 2009.
29. S. Suri, G.B. Viswanathan, T. Neeraj, D.-H. Hou, and M.J. Mills: Acta Mater., 1999, vol. 47, no. 3, pp. 1019-34.10.1016/S1359-6454(98)00364-4 ↗
30. M.F. Savage, J. Tatalovich, and M.J. Mills: Phil. Mag., 2004, vol. 84, no. 11, pp. 1127-54.10.1080/1478643032000158305 ↗
31. V. Sinha, M.J. Mills, and J.C. Williams: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2015-26.10.1007/s11661-006-0144-5 ↗
32. G. Lütjering: Mater. Sci. Eng. A, 1998, vol. 243, pp. 32-35.10.1016/S0921-5093(97)00778-8 ↗
33. G. Lütjering and J.C. Williams: Titanium, Springer-Verlag, New York, NY, 2003.10.1007/978-3-540-71398-2 ↗
34. J.M. Larsen: Ph.D Dissertation, Carnegie Mellon University, Pittsburgh, PA, 1987.
35. S. Suresh: Fatigue of Materials, 2nd ed., Cambridge University Press, New York, NY, 1998.10.1017/CBO9780511806575 ↗
36. L. Wagner, J.K. Greogory, A. Gysler, and G. Lütjering: Small Fatigue Cracks, Proc. The Second Engineering Foundation International Conference/Workshop, R.O. Ritchie and J. Lankford, eds.,TMS, Santa Barbara, CA, 1986, pp. 117-27.
37. C.C. Wojcik, K.S. Chan, and D.A. Koss: Acta Metall., 1988, vol. 36, no. 5, pp. 1261-70.10.1016/0001-6160(88)90278-7 ↗
38. A.L. Pilchak, A. Bhattacharjee, A.H. Rosenberger, and J.C. Williams: Int. J. Fatigue, 2009, vol. 31, pp. 989-94.10.1016/j.ijfatigue.2008.03.036 ↗
39. D.L. Davidson and D. Eylon: Metall. Mater. Trans. A, 1980, vol. 11A, pp. 837-43.10.1007/BF02661213 ↗
40. D. Eylon: J. Mater. Sci., 1979, vol. 14, pp. 1914-22.10.1007/BF00551032 ↗
41. D. Eylon: Trans. TMS-AIME, 1979, vol. 10, no. 3, pp. 311-17.
42. D. Eylon and B. Strope: J. Mater. Sci., 1979, vol. 14, pp. 345-53.10.1007/BF00589825 ↗
43. A.L. Pilchak, D.M. Norfleet, M.C. Juhas, and J.C. Williams: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 1519-24.10.1007/s11661-007-9236-0 ↗
44. R.J. Simpkins II, M.P. Rourke, T.R. Bieler, and P.A. McQuay: Mater. Sci. Eng. A, 2007, vol. 463, pp. 208-15.10.1016/j.msea.2006.09.114 ↗
45. J.-H. Jeon, A.B. Godfrey, P.A. Blenkinsop, W. Voice, and Y.-D. Hahn: Mater. Sci. Eng. A, 1999, vol. 271, pp. 128-33.10.1016/S0921-5093(99)00192-6 ↗
46. J. Ault: Precision Castparts Corp., private communication, May, 2009.
47. L.R. Saitova, H.W. Hoppel, M. Goken, I.P. Semenova, G.I. Raab, and R.Z. Valiev: Mater. Sci. Eng. A, 2009, vol. 503, pp. 145-47.10.1016/j.msea.2008.04.082 ↗
48. L.R. Saitova, H.W. Hoppel, M. Goken, I.P. Semenova, and R.Z. Valiev: Int. J. Fatigue, 2009, vol. 31, pp. 322-31.10.1016/j.ijfatigue.2008.08.007 ↗
49. A.W. Thompson and B.C. Odegard: Metall. Trans. A, 1973, vol. 4A, pp. 899-908.10.1007/BF02645587 ↗
50. S. Suri, T. Neeraj, G.S. Daehn, D.-H. Hou, J.M. Scott, R.W. Hayes, and M.J. Mills: Mater. Sci. Eng. A, 1997, vol. 234-236, pp. 996-99.10.1016/S0921-5093(97)00322-5 ↗
51. T. Neeraj, D.-H. Hou, G.S. Daehn, and M.J. Mills: Acta Mater., 2000, vol. 48, pp. 1225-38.10.1016/S1359-6454(99)00426-7 ↗
52. S. Zherebtsov, G. Salishchev, R. Galeyev, and K. Maekawa: Mater. Trans., 2005, vol. 46, no. 9, pp. 2020-25.10.2320/matertrans.46.2020 ↗