Precipitate microstructures and resulting properties of Al-Zn-Mg metal inert gas-weld heat-affected zones
Source abstract
Abstract
Using the combination of small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the precipitate microstructure is quantitatively investigated in the heat-affected zones (HAZs) of Al-Zn-Mg metal inert gas (MIG)-welds, and the resulting mechanical properties are determined by hardness measurements. Three initial states prior to welding (T4, T6, and T7) are investigated, and the subsequent microstructure evolution during natural aging and postwelding heat treatments (PWHTs) is assessed. The critical part of the HAZ is shown to be the transition region where partial dissolution of the initially present precipitates occurs. In this transition zone, precipitate coarsening is shown to occur for the T6 and T7 initial states, contrarily to the T4 material. After PWHT, the T6 and T7 materials experience a weak region related to this coarsening behavior, whereas the T4 material HAZ is able to recover a homogeneous microstructure after a suitably chosen PWHT. Simple model ramp heat treatments are shown to describe the main phenomena involved in the HAZ. Finally, a precipitation hardening model is successfully applied to the microstructural data to describe the hardness profiles in the various HAZs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Advanced Welding Techniques Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. B. Bjørneklett, Ø. Grong, A.O. Kluken, and O. Jensrud: Mater. Sci. Forum, 1996, vols. 217–222, pp. 1527–32.10.4028/www.scientific.net/MSF.217-222.1527 ↗
2. Z.J. Lu, W.J. Evans, J.D. Parker, and S. Birley: Mater. Sci. Eng. A, 1996, vol. A220, pp. 1–7.
3. H.T. Kim and S.W. Nam: Scripta Mater., 1996, vol. 34 (7), pp. 1139–45.10.1016/1359-6462(95)00644-3 ↗
4. W. Hepples, M.C. Thunton, and N.J.H. Holroyd: J. Mater. Sci., 1992, vol. 27, pp. 5720–26.10.1007/BF01119728 ↗
5. H. Cordier, M. Schippers, and I. Polmear: Z. Metallk., 1977, vol. 68, pp. 280–84.
6. Ø. Grong: in Metallurgical Modelling of Welding, 2nd ed., H.K.D.H. Bhadeshia, ed., Institute of Materials, London, 1997.
7. O.R. Myhr, S. Klokkehaug, H.G. Fjaer, Ø. Grong, and A.O. Kluken: Proc. 5th Int. Conf. on Trends in Welding Research, Georgia, June 1–5, 1998.
8. B.I. Bjørneklett, Ø. Grong, O.R. Myhr and A.O. Kluken: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2667–77.10.1007/s11661-999-0307-2 ↗
9. R.Y. Hwang and C.P. Chou: Scripta Mater., 1998, vol. 38 (2), pp. 215–21.10.1016/S1359-6462(97)00472-7 ↗
10. T. Ma and G. den Ouden: Mater. Sci. Eng. A, 1999, vol. A266, pp. 198–204.10.1016/S0921-5093(99)00020-9 ↗
11. A. Deschamps, L. David, M. Nicolas, F. Bley, F. Livet, R. Seguela, J.P. Simon, Vigier, G, and J.C. Werenskiold: Adv. Eng. Mater., 2001, vol. 8, pp. 579–86.10.1002/1527-2648(200108)3:8<579::AID-ADEM579>3.0.CO;2-R ↗
12. H. Löffler, I. Kovács, and J. Lendvai: J. Mater. Sci., 1983, vol. 18, pp. 2215–40.10.1007/BF00541825 ↗
13. S.P. Ringer and K. Hono: Mater. Characterization, 2000, vol. 44, pp. 101–31.10.1016/S1044-5803(99)00051-0 ↗
14. B. Gueffroy and H. Löffler: Physica Status Solidi (a), 1981, vol. 66, pp. 585–90.10.1002/pssa.2210660221 ↗
15. P. Gomiero, A. Reeves, A. Pierre, F. Bley, F. Livet, and H. Vichery: Proc. 4th Conf. on Aluminum Alloys: Their Physical and Mechanical Properties, Atlanta, GA, Sept. 11–16, 1994, Georgia Institute of Technology, School of Materials Science and Engineering, Atlanta, GA, vol. 1, pp. 644–51.
16. R. Ferragut, A. Somoza, and A. Dupasquier: J. Phys.: Condensed Matter, 1996, vol. 8, pp. 8945–52.10.1088/0953-8984/8/45/026 ↗
17. J.K. Park: Mater. Sci. Eng. A, 1988, vol. A103, pp. 223–31.10.1016/0025-5416(88)90512-5 ↗
18. M. Radomsky, O. Kabisch, H. Löffler, J. Lendvai, T. Ungár, J. Kovács, and G. Honyek: J. Mater. Sci., 1979, vol. 14, pp. 2906–12.10.1007/BF00611473 ↗
19. X.J. Jiang, B. Noble, B. Holme, G. Waterloo, and J. Tafto: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 339–48.10.1007/s11661-000-0269-x ↗
20. X. Li and M.J. Starink: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1071–76.10.4028/www.scientific.net/MSF.331-337.1071 ↗
21. Metals Handbook, vol. 6, Welding and Brazing, 8th ed., ASM, Metals Park, OH, 1971.
22. A. Deschamps, Y. Bréchet, and F. Livet: Mater. Sci. Technol., 1999, vol. 15(9), pp. 993–1000.10.1179/026708399101506832 ↗
23. M. Nicolas and A. Deschamps: LTPCM, Grenoble, France, unpublished research, 2003.
24. O.R. Myhr, H.G. Fjaer, S. Klokkehaug, E.J. Holm, Ø. Grong, and A.O. Kluken: Proc. 9th Int. Conf. on Computer Technology in Welding, Detroit, MI. Sept, 28–30, 1999.
25. W. Lacom, H.P. Degischer, A. Zahra, and C.Y. Zahra: Z. Metallk., 1982, vol. 73 (12), pp. 781–85.
26. K. Asano, M. Abe, and A. Fujiwara: Mater. Sci. Eng., 1976, vol. 22, pp. 61–70.10.1016/0025-5416(76)90135-X ↗
27. R.W. Cahn and P. Haasen: Physical Metallurgy, 4th ed., Cambridge University Press, Cambridge, 1996, vol. 3.
28. J. Lendvai: Mater. Sci. Forum, 1996, vols. 217–222, pp. 43–56.10.4028/www.scientific.net/MSF.217-222.43 ↗
29. V. Gerold: Dislocation in Solids, North-Holland Publishing Company, Amsterdam, The Netherlands, 1979, vol. 4, p. 219.
30. U.F. Kocks, A.S. Argon, and M.F. Ashby: Progr. Mater. Sci., 1975, vol. 19, p. 1.10.1016/0079-6425(75)90005-5 ↗
31. S.C. Chang, M.T. Jahn, C.M. Wan, J.Y.N. Lee, and T.K. Hsu: J. Mater. Sci., 1976, vol. 11, pp. 623–30.10.1007/BF01209447 ↗
32. A. Deschamps, S. Esmaeili, W.J. Poole, and M. Militzer: Proc. 6th Japan-France Materials Science Seminar, Poitiers, France 1999; J. Phys. IV France, 2000, vol. 10, PR6, pp. 151–56.