Cold Cracking Development in AA7050 Direct Chill–Cast Billets under Various Casting Conditions
Source abstract
Abstract
Cold cracking is a potentially catastrophic phenomenon in direct chill (DC) casting of 7xxx series aluminum alloys that leads to safety hazards and loss of production. The relatively low thermal conductivity and wide solidification temperature range in these alloys results in accumulation of residual thermal stress under nonuniform cooling conditions of the billets. In addition, such alloys show a severe loss in ductility below a critical temperature of 573 K (300 °C). This brittleness along with high stress concentration at the tips of voids and microcracks can lead to catastrophic failure. Casting process parameters affect the magnitude and distribution of stresses in the billet and increase the susceptibility of the material to cold cracking. In order to investigate the effect of casting process parameters such as casting speed, billet size, and water flow rate, thermomechanical simulations were applied using ALSIM5 casting simulation software. Among the studied casting process parameters, the increased billet size and high casting speed resulted in the most dramatic increase in residual stress level. Critical crack sizes that led to catastrophic failure were also calculated and are reported against process parameters.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Bauxite Residue and Utilization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. J.F. Grandfield and P.T. McGlade: Mater. Forum, 1996, vol. 20, pp. 29–51.
2. U. Chandra and A. Ahmed: in Modeling for Casting and Solidification Processing, K.-O. Yu, ed., Marcel Dekker Inc., New York, 2002, pp. 55–93.
3. J.R. Davis: Aluminium and Aluminium Alloys, ASM Speciality Handbook, ASM INTERNATIONAL, Materials Park, OH, 1994, pp. 68–69.
4. M. Lalpoor, D.G. Eskin, and L. Katgerman: Mater. Sci. Eng., A, 2008, vol. 497, pp. 186–94.10.1016/j.msea.2008.06.047 ↗
5. J.B. Hess: Metall. Trans. A, 1983, vol. 14A, pp. 323–27.10.1007/BF02644210 ↗
6. B. Hannart, F. Cialti, and R. Van Schalkwijk: in Light Metals 1994, U. Mannweiler, ed., TMS, Warrendale, PA, 1994, pp. 879–87.
7. Z. Yubo, C. Jianzhong, Z. Zhihao, Z. Haitao, and Q. Ke: Mater. Sci. Eng., A, 2005, vol. 406, pp. 286–92.10.1016/j.msea.2005.07.001 ↗
8. W. Roth: Z. Metallkd., 1949, vol. 40 (12), p. 145.
9. B. Commet, P. Delaire, J. Rabenberg, and J. Storm: in Light Metals, P.N. Crepeau, ed., TMS, Warrendale, PA, 2003, pp. 711–17.
10. K. Matsuda, S. Nagai, Y. Miyate, H. Maehara, and I. Tsukuda: 6th Int. Aluminum Extrusion Technology Seminar, Aluminium Association and Aluminium Extruder’s Council, Chicago, IL, 1996, vol. I, pp. 525–28.
11. A. Burghardt, B. Commet, J.-M. Drezet, and H.G. Fjær: in Modeling of Casting, Welding and Advanced Solidification Processes IX, P.R. Sahm, P.N. Hansen, and J.G. Conley, eds., Shaker Verlag, Aachen, Germany, 2000, pp. 25–32.
12. W. Schneider, E.K. Jensen, and B. Carrupt: in Light Metals, J. Evans, ed., TMS, Warrendale, PA, 1995, pp. 961–67.
13. S. Benum, D. Mortensen, H. Fjær, H.-G. Øverlie, and O. Reiso: Light Metals, 2002, W. Schneider, ed., TMS, Warrendale, PA, 2002, pp. 967–74.
14. J.L. Dassel and T.C. Zinniger: in Light Metals, TMS-AIME, Warrendale, PA, 1982, pp. 793–801.
15. US Patent No. US2007/0102136 A1, 2007.
16. K.-M. Chang and B. Kang: J. Chin. Inst. Eng., 1999, vol. 22, pp. 27–42.10.1080/02533839.1999.9670439 ↗
17. J.M. Drezet and M. Rappaz: in Light Metals, J. Evans, ed., TMS, Warrendale, PA, 1995, pp. 941–50.
18. H.G. Fjær and A. Mo: Metall. Trans. B, 1990, vol. 21B, pp. 1049–61.
19. W. Boender, A. Burghardt, E.P. van Klaveren, and J. Rabenberg: in Light Metals, A.T. Tabereaux, ed., TMS, Warrendale, PA, 2004, pp. 679–84.
20. O. Ludwig, J.-M. Drezet, B. Commet, and B. Heinrich: in Modeling of Casting, Welding and Advanced Solidification Processes XI, C.-A. Gandin and M. Bellet, eds., TMS, Warrendale, PA, 2006, pp. 185–92.
21. W. Boender and A. Burghardt: Proc. 5th Decennial Int. Conf. on Solidification Processing, H. Jones, ed., University of Sheffield, Sheffield, United Kingdom, 2007, pp. 714–18.
22. M. Lalpoor, D.G. Eskin, and L. Katgerman: Metall. Mater. Trans. A, 2009, vol. 40A, pp. 3304–13.10.1007/s11661-009-0031-y ↗
23. E.E. Madsen and G.E. Fladmark: in Numerical Solution of Partial Differential Equations, G.E. Fladmark and J.G. Gram, eds., D. Reidel Publishing Company, Dordrecht, The Netherlands, 1973, pp. 223–40.10.1007/978-94-010-2672-7_9 ↗
24. E.E. Madsen: in Numerical Methods in Thermal Problems, R.W. Lewis and K. Morgan, eds., Pineridge Press Limited, Swansea, United Kingdom, 1979, pp. 81–89.
25. H. Fossheim and E.E. Madsen: in Light Metals, W.S. Peterson, ed., TMS-AIME, Warrendale, PA, 1979, pp. 695–720.
26. E.K. Jensen and W. Schneider: in Light Metals, C.M. Bickert, ed., TMS-AIME, Warrendale, PA, 1990, pp. 937–43.
27. D. Mortensen: Metall. Mater. Trans. B, 1999, vol. 30B, pp. 119–33.10.1007/s11663-999-0012-y ↗
28. M. Lalpoor, D.G. Eskin, and L. Katgerman: Proc. 12th Int. Conf. on Fracture, Ottawa, 2009, National Research Council of Canada, Ottawa, Canada, 2009 (CD).
29. B. Magnin, L. Katgerman, and B. Hannart: in Modeling of Casting, Welding and Advanced Solidification Processes VII, M. Cross and J. Campbell, eds., TMS, Warrendale, PA, 1995, pp. 303–10.
30. O. Ludwig, B. Commet, J.-M. Drezet, C.L. Martin, and M. Suery: in Modeling of Casting, Welding and Advanced Solidification Processes X, D.M. Stefanescu, J. Warren, M. Jolly, and M. Krane, eds., TMS, Warrendale, PA, 2003, pp. 183–90.
31. M. M’Hamdi, A. Mo, and H.G. Fjær: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 3069–83.10.1007/s11661-006-0188-6 ↗
32. D.G. Eskin, Suyitno, J.F. Mooney, and L. Katgerman: Metall. Mater. Trans. A, 2004, vol. 35A, pp. 1325–35.10.1007/s11661-004-0307-1 ↗
33. O. Ludwig, J.-M. Drezet, C.L. Martin, and M. Suéry: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 1525–35.10.1007/s11661-005-0244-7 ↗
34. M. Lalpoor, D.G. Eskin, and L. Katgerman: Proc. THERMEC 2009, Adv. Mater. Res., 2010, vols. 89–91, pp. 319–24.10.4028/www.scientific.net/AMR.89-91.319 ↗
35. M. Schöllmann, H.A. Richard, G. Kullmer, and M. Fulland: Int. J. Fract., 2002, vol. 117, pp. 129–41.10.1023/A:1020980311611 ↗
36. H. Tada, P.C. Paris, and G.R. Irwin: The Stress Analysis of Cracks Handbook, 3rd ed., ASME, New York, NY, 2000, pp. 342 and 410.10.1115/1.801535 ↗
37. V.A. Livanov: in Aluminum Alloys, A.F. Belov and G.D. Agarkov, eds., Oborongiz, Moscow, 1955, pp. 128–68.
38. R.K. Paramatmuni, K.-M. Chang, B.S. Kang, and X. Liu: Mater. Sci. Eng. A, 2004, vol. 379, pp. 293–301.10.1016/j.msea.2004.02.026 ↗
39. S.C. Flood, P.A. Davidson, and S. Rogers: in Modeling of Casting, Welding and Advanced Solidification Processes VII, M. Cross and J. Campbell, eds., London, 1995, pp. 801–08.
40. V.I. Dobatkin: Continuous Casting and Casting Properties of Alloys, Moscow, Oborongiz, 1948.
41. N. Noda, R.B. Hetnarski, and Y. Tanigawa: Thermal Stresses, 2nd ed., Taylor & Francis, New York, NY, 2003, pp. 221–93.
42. J. Langlais, T. Bourgeois, Y. Caron, G. Beland, and D. Bernard: in Light Metals, J. Evans, ed., TMS, Warrendale, PA, 1995, pp. 979–86.