The strain dependence of postdynamic recrystallization in 304 H stainless steel
Source abstract
Abstract
Using double-hit hot compression tests, the softening behavior of 304 H stainless steel was studied during unloading. The prestrains used were associated with the initiation of dynamic recrystallization (DRX) (e c), the peak strain (e p), 1/2 (e c+e p), the strain at maximum softening rate (e i), and the onset of steady state flow (e s). The following conditions of deformation were used: T=1000 °C, 1050 °C, and 1100 °C, $$\dot \varepsilon $$ =0.01 and 0.1 s−1, and delay times of 0.3 to 1000 seconds. To define the above important strains, single-hit hot compression tests were performed over a wider range of deformation conditions than the double-hit ones—i.e., 900 °C to 1100 °C and $$\dot \varepsilon $$ =0.01 to 1 s−1. The results show that a transition strain (e*) separates the strain-dependent range of postdynamic softening from the strain-independent range. At strains between e c and e*, both metadynamic and static recrystallization contribute to interhit softening. The value of e* obtained in this work was e*=4/3 e p. It was also found that the strain hardening rate was identical at all the critical strains (e*) and took the value −22 MPa.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. A. Belyakov, H. Miura, and T. Sakai: Scripta Mater., 2000, vol. 43, p. 21.10.1016/S1359-6462(00)00373-0 ↗
2. M. El Wahabi, J.M. Cabrera, and J.M. Prado: Mater. Sci. Eng., 2003, vol. A343, p. 116.10.1016/S0921-5093(02)00357-X ↗
3. H.J. McQueen, N. Jin, and N.D. Ryan: Mater. Sci. Eng. A, 1995, vol. 190, p. 43.10.1016/0921-5093(94)09599-R ↗
4. A. Dehghan-Manshadi, H. Beladi, M.R. Barnett, and P.D. Hodgson: Mater. Sci. Forum, 2004, vol. 467–470, p. 1163.10.4028/www.scientific.net/MSF.467-470.1163 ↗
5. G.R. Stewart, J.J. Jonas, and F. Montheillet: ISIJ Int., 2004, vol. 44 (7), p. 1263.10.2355/isijinternational.44.1263 ↗
6. H.J. McQueen, S. Yue, N.D. Ryan, and E. Fry: Mater. Process. Technol., 1995, vol. 53, p. 293.10.1016/0924-0136(95)01987-P ↗
7. G.R. Stewart and J.J. Jonas: ISIJ Int., 2004, vol. 44 (7), p. 1581.10.2355/isijinternational.44.1581 ↗
8. R.A.P. Djaic and J.J. Jonas: Metall. Trans., 1973, vol. 4, p. 621.10.1007/BF02648720 ↗
9. S.H. Cho, K.B. Kang, and J.J. Jonas: ISIJ Int., 2001, vol. 41 (7), p. 766.10.2355/isijinternational.41.766 ↗
10. P. Uranga, A.I. Fernandez, B. Lopez, and J.M. Rodriguez-Ibabe: Mater. Sci. Eng. A, 2003, vol. 345, p. 319.10.1016/S0921-5093(02)00510-5 ↗
11. S. Matthies and G.W. Vinel: Phys. Stat. Sol. (b), 1982, vol. 112, pp. K111-K114.10.1002/pssb.2221120254 ↗
12. S. Matthies and G.W. Vinel: Phys. Stat. Sol. (b), 1982, vol. 112, pp. K115-K120.10.1002/pssb.2221120255 ↗
13. E.I. Poliak and J.J. Jonas: Acta Mater., 1996, vol. 44 (1), p. 127.10.1016/1359-6454(95)00146-7 ↗
14. E.I. Poliak and J.J. Jonas: ISIJ Int., 2003, vol. 43 (5), p. 684.10.2355/isijinternational.43.684 ↗
15. E.I. Poliak and J.J. Jonas: ISIJ Int., 2003, vol. 43 (5), p. 692.10.2355/isijinternational.43.692 ↗
16. J.J. Jonas and E.I. Poliak: Mater. Sci. Forum, 2003, vol. 426–432, p. 57.10.4028/www.scientific.net/MSF.426-432.57 ↗
17. E.I. Poliak and J.J. Jonas: ISIJ Int., 2004, vol. 44 (11), p. 1874.10.2355/isijinternational.44.1874 ↗
18. A. Najafizadeh and J.J. Jonas: ISIJ Int. 2006, in press.
19. S.F. Medina and C.A. Hernandez: Acta Mater., 1996, vol. 44, p. 147.
20. S.F. Medina and C.A. Hernandez: Acta Mater., 1996, vol. 44, p. 149.10.1016/1359-6454(95)00152-2 ↗
21. C.A. Hernandez, S.F. Medina, and J. Ruiz: Acta Mater., 1996, vol. 44, p. 155.10.1016/1359-6454(95)00153-4 ↗
22. S.F. Medina and C.A. Hernandez: Acta Mater., 1996, vol. 44, p. 165.10.1016/1359-6454(95)00154-6 ↗
23. C.M. Sellars: Mater. Sci. Technol., 1990, vol. 6, p. 1072.10.1179/mst.1990.6.11.1072 ↗
24. C.M. Sellars and J. Perttula: ISIJ Int., 1996, vol. 36, p. 729.10.2355/isijinternational.36.729 ↗