Microstructural Evolution, Hardness, and Alligatoring in the Mushy State Rolled Cast Al-4.5Cu Alloy and In-Situ Al4.5Cu-5TiB2 Composite
Source abstract
Abstract
A comparative study has been carried out on the microstructural evolution and hardness of the Al-4.5Cu alloy and in-situ Al-4.5Cu-5TiB2 composite, either water quenched from, or subjected to, rolling at mushy zone temperatures. The cast alloy shows coarse α-Al dendrites, while the composite contains rosette-type grains with TiB2 particles located at the grain boundaries. The plate-shaped specimens, in cast or pre-hot-rolled conditions, have been rolled at temperatures corresponding to 10, 20, or 30 vol pct liquid to thickness reductions in the range of 2.5 to 10 pct. While the alloy could be rolled defect free, the cast composites undergo alligatoring, except when thickness reduction is 5 pct or lower at 30 vol pct liquid. Alligatoring is caused by strain localization and shear failure, and is prevented partially on prior hot rolling, causing homogenization and equiaxed grain formation. Mushy state rolling leads to nearly equiaxed grains having bimodal size distributions. The surfaces with a larger volume fraction of finer grains exhibit higher microhardness than the center. Exposure to mushy zone causes grain growth in the alloy but not in the composite, due to Zener pinning by TiB2 particles. On rolling at low liquid content to a large thickness reduction, the unmelted grains deform and work-harden significantly, causing an increase in hardness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. G. Hirt, R. Cremer, T. Witulski, H.C. Tinius: Mater. Des., 1997, vol. 18 (4–6), pp. 315–2110.1016/S0261-3069(97)00071-X ↗
2. C.S. Rice, P.F. Mendez: Adv. Mater. Processes, 2001, vol. 159 (10), pp. 49–52
3. M. Kiuchi, S. Sugiyama, K. Arai: J. Jpn. Soc. Technol. Plast., 1979, vol. 20 (223), pp. 762–69
4. A.A. Tseng, J. Horsky, M. Raudensky, P. Kotrbacek: Mater. Des, 2001, vol. 22 (2), pp. 83–9110.1016/S0261-3069(00)00058-3 ↗
5. M. Kiuchi, R. Kopp: Ann. CIRP, 2002, vol. 51 (2), pp. 653–7010.1016/S0007-8506(07)61705-3 ↗
6. E. Tzimas, A. Zavaliangos: Acta Mater., 1999, vol. 47 (2), pp. 517–2810.1016/S1359-6454(98)00356-5 ↗
7. M. Kiuchi: in Plasticity and Modern Metal Forming Technology, T.Z. Blazynski, ed., Elsevier Applied Science, New York, NY, 1989, pp. 289–313
8. M.C. Flemings: Solidification Processing, McGraw-Hill Book Co., New York, NY, 1974, pp. 21–23
9. W.G. Cho, C.G. Kang: J. Mater. Process. Technol., 2000, vol. 105, pp. 269–7710.1016/S0924-0136(00)00577-X ↗
10. J. Baur: Proc. 6th Int. Conf. Semisolid Processing of Alloys and Composites, G.L. Chiarmetta and M. Rosso, eds., Edimet Spa, Brescia, Italy, 2000, pp. 289–94
11. K. Siegert, A. Wolf, J. Baur: Prod. Eng. (Ann. German Acad. Soc. Prod. Eng.), 2000, vol. VII (1), pp. 21–24
12. M.M. Rovira, B.C. Lancini, M.H. Robert: J. Mater. Process. Technol., 1999, vols. 92–93, pp. 42–4910.1016/S0924-0136(99)00220-4 ↗
13. H.-J. Li, L.-H. Qi, S.-J. Luo, W.-C.Z.R.H. Wang: J. Mater. Process. Technol., 1995, vol. 55 (1), pp. 19–2310.1016/0924-0136(95)01805-0 ↗
14. R.A. Martinez, M.C. Flemings: Metall. Mater. Trans. A, 2005, vol. 36A, pp. 2205–1010.1007/s11661-005-0339-1 ↗
15. M.C. Flemings and R.A. Martinez: in Semi-Solid Processing of Alloys and Composites, Proc. 9th Int. Conf. on Semi-Solid Processing of Alloys and Composites, C.G. Kang, S.K. Kim, and S.Y. Lee, eds., Trans Tech Publications, Aedermannsdorf, Switzerland, 2006
16. Solid State Phenomena, 2006, vols. 116-117, pp. 1-810.4028/www.scientific.net/SSP.116-117.1 ↗
17. R.A. Martinez, A. Karma, M.C. Flemings: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 2807–1510.1007/BF02586113 ↗
18. L. Zu, S. Luo: J. Mater. Proc. Technol., 2001, vol. 114 (3), pp. 189–9310.1016/S0924-0136(01)00738-5 ↗
19. D.K. Lee, H.K. Jung, and C.G. Kang: Proc. 3rd Int. Conf. on Intelligent Processing and Manufacturing of Materials, J.M. Meech, M.M. Veiga, Y. Kawazoe, and S.R. LeClair, eds., CRC Press, Boca Raton, FL, 2003, pp. 731–38
20. M. Kiuchi, S. Sugiyana: Ann. CIRP, 1991, vol. 40, pp. 259–6110.1016/S0007-8506(07)61982-9 ↗
21. A. Mandal, R. Maiti, M. Chakraborty, B.S. Murty: Mater. Sci. Eng. A, 2004, vol. 386, pp. 296–30010.1016/j.msea.2004.07.026 ↗
22. ASM Handbook, ASM INTERNATIONAL, Materials Park, OH, 1992, vol. 3, pp. 1.23 and 2.44
23. E. Tzimas, A. Zavaliangos: J. Mater. Sci., 2000, vol. 35, pp. 5319–2910.1023/A:1004890711322 ↗
24. ASTM Standard E 112–96e2, Annual Book of ASTM Standards, ASTM, Philadelphia, PA, 2003, pp. 1–26
25. D.A. Porter and K.E. Easterling: Phase Transformations in Metals and Alloys, Chapman and Hall, London, 1992, pp. 186–26210.1007/978-1-4899-3051-4 ↗
26. E.J. Zoqui, M.H. Robert: J. Mater. Process. Technol., 1998, vol. 78, pp. 198–20310.1016/S0924-0136(97)00483-4 ↗
27. S. Laksmi, L. Lu, M. Gupta: J. Mater. Process. Technol., 1998, vol. 73, pp. 160–6610.1016/S0924-0136(97)00225-2 ↗
28. R. Mitra, W.A. Chiou, M.E. Fine, J.R. Weertman: J. Mater. Res., 1993, vol. 8, pp. 2380–9210.1557/JMR.1993.2380 ↗
29. E.J. Zoqui: J. Mater. Process. Technol., 2003, vols.145 and 144, pp. 195–20110.1016/S0924-0136(03)00418-7 ↗
30. M. Braccini, C.L. Martin, A. Tourabi, Y. Brechest, M. Suery: Mater. Sci. Eng. A, 2002, vol. 337, pp. 1–1110.1016/S0921-5093(02)00042-4 ↗
31. A. Mortensen: Metall. Trans. A, 1991, vol. 22A, pp. 569–7410.1007/BF02656824 ↗
32. E.J. Zoqui and M.H. Robert: Proc. 4th Int. Conf. on Semisolid Processing of Alloys and Composites, D.H. Kirkwood and P. Kapranos, eds., University of Sheffield Press, Sheffield, United Kingdom, 1996, pp. 75–78
33. M.H. Robert: Trans. Jpn. Foundrymen Soc., 1993, vol. 12, pp. 45–51
34. M. Corteu, J.L. Charman: Int. Met. Rev., 1983, vol. 28, pp. 228–50
35. K.K. Ray, D.K. Das: Scripta Metall., 1989, vol. 23, pp. 681–84
36. K.K. Ray, R. Mitra, A. Bhadhuri: Cast Met., 1995, vol. 8, pp. 65–7110.1080/09534962.1995.11819195 ↗
37. D. Fabregue, A. Deschamps, M. Suery, W.J. Poole: Metall. Mater. Trans. A, 2006, vol. 37A, pp. 1459–6710.1007/s11661-006-0090-2 ↗
38. G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill Book Co., New York, NY, 1986, p. 586
39. B. Avitzur, C.J. Van Tyne, S. Turczyn: ASME J. Eng. Ind., 1988, vol. 110, pp. 173–7810.1115/1.3187866 ↗
40. S. Turczyn, Z. Malinowski: in Materials Processing Defects, S.K. Ghosh, M. Predeleanu, eds., Elsevier, New York, NY, 1996, p. 401
41. L. Xu, G.S. Daehn: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 589–9810.1007/BF02651600 ↗
42. W. Rudnicki, J.R. Rice: J. Mech. Phys. Solids, 1975, vol. 23, 371–39410.1016/0022-5096(75)90001-0 ↗
43. R. Raj, M.F. Ashby: Metall. Trans., 1971, vol. 2, pp. 1113–2710.1007/BF02664244 ↗
44. R. Raj, M.F. Ashby: Acta Metall., 1975, vol. 23, pp. 653–6610.1016/0001-6160(75)90047-4 ↗
45. R.G. Fleck, D.M.R. Taplin, C.J. Beevers: Acta Metall., 1975, vol. 23, pp. 415–2410.1016/0001-6160(75)90081-4 ↗
46. I.-W. Chen, A.S. Argon: Acta Metall., 1981, vol. 29, pp. 1321–3310.1016/0001-6160(81)90023-7 ↗
47. R. Raj: Proc. Int. Congress of Intergranular and Interphase Boundaries in Materials, M. Aucouturier (ed.), Les Editions de Physique, Paris, France, Colloque De Physique, 1990, Colloque C1, vol. 51, pp. C1-393–C1-40110.1051/jphyscol:1990161 ↗
48. J. Bear: Dynamics of Fluids in Porous Media, American Elsevier, New York, NY, 1972, 90–120
49. D. Duly, J.G. Lenard, and J.A. Schey: J. Mater. Process. Technol., 1998, vol. 75, pp. 143–5110.1016/S0924-0136(97)00317-8 ↗
50. B.V. Radhakrishna Bhat, Y.R. Mahajan, H.Md. Roshan, Y.V.R.K. Prasad: Metall. Trans. A, 1992, vol. 23A, pp. 2223–3010.1007/BF02646015 ↗
51. O.D. Sherby, J.D. Wadsworth: Progr. Mater. Sci., 1989, vol. 33, pp. 169–22110.1016/0079-6425(89)90004-2 ↗
52. M.A. Herbert, R. Maiti, R. Mitra, and M. Chakraborty: Semi-Solid Processing of Alloys and Composites, Proc. 9th Int. Conf. on Semi-Solid Processing of Alloys and Composites, C.G. Kang, S.K. Kim, and S.Y. Lee, eds., Trans Tech Publications, Aedermannsdorf, Switzerland, 2006
53. Solid State Phenomena, 2006, vols. 116-117, pp. 217-2010.4028/www.scientific.net/SSP.116-117.217 ↗
54. J.M. Papazian: Metall. Trans. A, 1988, vol. 19A, pp. 2945–5310.1007/BF02647721 ↗