journal article·2008-08

Effects of Test Temperature and Loading Conditions on the Tensile Properties of a Zr-Based Bulk Metallic Glass

A.H. Vormelker, O.L. Vatamanu, L. Kecskes, J.J. Lewandowski

Publisher page

Abstract

The effects of changes in test temperature (20 °C, 260 °C, 330 °C, and 380 °C), strain rate (10−5 to 10−1 s−1), and loading conditions (displacement control vs loading-rate control) on the tensile behavior of Zr41.2Ti13.8Cu12.5Ni10Be22.5 (LiquidMetal 1 (LM1)), a bulk metallic glass (BMG), have been determined. Significant effects of the test temperature, strain rate, and loading condition were observed on the strength, ductility/elongation, and mechanisms of failure (shear, ductile rupture, etc.). This material exhibited extensive elongation (i.e., >100 pct) prior to failure when tested near the glass transition temperature (T g ≈ 375 °C) at sufficiently low strain rates, while higher strain rates or lower test temperatures produced shear fracture at low elongation. The flow and fracture behavior was also significantly affected by the loading condition (i.e., displacement vs loading-rate control). The effective strain rate necessary to cause failure in shear without significant global flow was several orders of magnitude lower in loading-rate control than in displacement control. Samples exhibiting high elongation tested in displacement control gently and convexly drew to a near point (i.e., ductile rupture). Samples tested at the same temperature exhibiting high elongation in loading-rate control rapidly and concavely necked, followed by drawing to a constant diameter “wire” (i.e., ductile drawing), eventually failing by nearly pure ductile rupture. All samples that displayed significant elongation did so inhomogeneously, and were characterized by non-Newtonian global flow.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. W.H. Wang, C. Dong, C.H. Sheck: Mater. Sci. Eng., R, 2004, vol. 44, pp. 44–8910.1016/j.mser.2004.03.001 ↗
2. A. Peker, W.L. Johnson: Appl. Phys. Lett., 1993, vol. 63, pp. 2342–4410.1063/1.110520 ↗
3. A. Mashur, R. Busch, and W.L. Johnson: J. Non-Cryst. Solids, 1999, vol. 252, Part 2, pp. 566–7110.1016/S0022-3093(99)00133-7 ↗
4. J. Lu, G. Ravichandran, W.L. Johnson: Acta Mater., 2003, vol. 51, pp. 3429–4310.1016/S1359-6454(03)00164-2 ↗
5. P. Lowhaphandu, L.A. Ludrosky, J.J. Lewandowski: Intermetallics, 2000, vol. 8, pp. 487–9210.1016/S0966-9795(99)00137-5 ↗
6. P. Lowhaphandu, S.L. Montgomery, J.J. Lewandowski: Scripta Mater., 1999, vol. 41, pp. 19–2410.1016/S1359-6462(99)00128-1 ↗
7. J. Wadsworth, T.G. Nieh: in Superplasticity—Current Status and Future Potential, P.B. Berbon, T. Sakuma, T.G. Langdon, eds., MRS, Boston, MA, 1999, vol. 601, pp.141–51
8. F. Spaepen: Acta Mater., 1979, vol. 25, pp. 407–1510.1016/0001-6160(77)90232-2 ↗
9. H. Eyring: J. Chem. Phys., 1936, vol. 4, pp. 283–9110.1063/1.1749836 ↗
10. A.S. Argon: Acta Metall., 1979, vol. 37, pp. 47–5810.1016/0001-6160(79)90055-5 ↗
11. H.A. Bruck, T. Christman, A.J. Rosakis, W.L. Johnson: Scripta Mater., 1994, vol. 30, pp. 429–3410.1016/0956-716X(94)90598-3 ↗
12. J.J. Lewandowski, P. Lowhaphandu: Philos. Mag. A, 2002, vol. 82, pp. 3427–4110.1080/01418610208240453 ↗
13. G. Sunny, J.J. Lewandowski, V. Prakash: J. Mater. Res., 2007, vol. 22, pp. 389–40110.1557/jmr.2007.0042 ↗
14. H.S. Chen: Acta Metall., 1974, vol. 22, pp. 1505–1110.1016/0001-6160(74)90112-6 ↗
15. H.S. Chen, C.E. Miller: Rev. Sci. Instrum., 1970, vol. 41, pp. 1237–3810.1063/1.1684774 ↗
16. J.J. Lewandowski, W.H. Wang, A.L. Greer: Philos. Mag. Lett., 2005, vol. 85, pp. 77–8710.1080/09500830500080474 ↗
17. Y.H. Liu, G. Wang, R.J. Wang, D.Q. Zhao, M.X. Pan, W.H. Wang: Science, 2007, vol. 315, pp. 1385–8810.1126/science.1136726 ↗
18. J. Schroers, W.L. Johnson: Phys. Rev. Lett., 2004, vol. 93, p. 25550610.1103/PhysRevLett.93.255506 ↗
19. V. Ponnambalam, J.S. Poon, G.J. Shiflet: J. Mater. Res., 2004, vol. 19, pp. 1320–2310.1557/JMR.2004.0176 ↗
20. W.H. Wang: J. Appl. Phys., 2006, vol. 99, p. 09350610.1063/1.2193060 ↗
21. M. Li, J. Eckert, L. Kecskes, J.J. Lewandowski: J. Mater. Res., 2007, vol. 22, pp. 255–5710.1557/jmr.2007.0069 ↗
22. C.L. Chiang, J.P. Chu, C.T. Lo, T.G. Nieh, Z.X. Wang, W.H. Wang: Intermetallics, 2004, vol. 12, pp. 1057–6110.1016/j.intermet.2004.04.012 ↗
23. K.S. Lee, Y.W. Chang: Met. Mater. Int., 2005, vol. 11, pp. 53–5710.1007/BF03027484 ↗
24. K.S. Lee, Y.W. Chang: Mater. Sci. Eng., A, 2005, vol. 399, pp. 238–4310.1016/j.msea.2005.03.103 ↗
25. M. Bletry, P. Guyot, Y. Brechet, J.J. Blandin, J.L. Soubeyroux: Mater. Sci. Eng., A, 2004, vol. 389, pp. 1005–1110.1016/j.msea.2004.02.085 ↗
26. M. Bletry, P. Guyot, Y. Brechet, J.J. Blandin, J.L. Soubeyroux: Intermetallics, 2004, vol. 12, pp. 1051–5510.1016/j.intermet.2004.04.019 ↗
27. Y.A. Cengal, R.H. Turner: Thermal-Fluid Sciences, McGraw-Hill, New York, NY, 2005, p. 471
28. Y. Kawamura, T. Shibita, A. Inoue, T. Masumoto: Scripta Mater., 1997, vol. 37, pp. 431–3610.1016/S1359-6462(97)00105-X ↗
29. P.D. Hey, J. Sietsma, A.V.D. Beukel: Acta Mater., 1998, vol. 46, pp. 5873–8210.1016/S1359-6454(98)00234-1 ↗
30. Y. Kawamura, T. Nakamura, A. Inoue: Scripta Mater., 1998, vol. 39, pp. 301–0610.1016/S1359-6462(98)00163-8 ↗
31. A.R. Leonhard, M. Heilmaier, J. Eckert: Scripta Mater., 2000, vol. 43, pp. 459–6410.1016/S1359-6462(00)00417-6 ↗
32. K.S. Lee, T.K. Ha, S. Ahn, Y.W. Chang: J. Non-Cryst. Solids, 2003, vol. 317, pp. 193–9910.1016/S0022-3093(02)01998-1 ↗
33. T.G. Neih, J. Wadsworth, C.T. Liu, T. Ohkubo, Y. Hirotsu: Acta Mater., 2001, vol. 49, pp. 2887–9610.1016/S1359-6454(01)00218-X ↗
34. G. Wang, J. Shen, J.F. Sun, Z.P. Lu, Z.H. Stachurski, B.D. Zhou: Intermetallics, 2005, vol. 13, pp. 642–4810.1016/j.intermet.2004.10.011 ↗
35. Y. Kawamura, T. Shibata, A. Inoue, T. Masumoto: Mater. Trans., JIM, 1999, vol. 40, pp. 335–4210.2320/matertrans1989.40.335 ↗
36. G.E. Dieter: Mechanical Metallurgy, McGraw-Hill, New York, NY, 1986, p. 242
37. T.G. Nieh, T. Mukai, C.T. Liu, J. Wadsworth: Scripta Mater., 1999, vol. 40, pp. 1021–2710.1016/S1359-6462(99)00071-8 ↗
38. W.A. Backofen: in Deformation Processing, M. Cohen, ed., Addison-Wesley Publishing Co., Inc., Tacloban City, Philippines, 1972, pp. 207–10
39. R. Hertzberg: High-Temperature Deformation Response of Crystalline Solids. Deformation and Fracture Mechanics of Engineering Materials, Wiley, New York, NY, 1995, pp. 175–78
40. P. Lowhaphandu: Ph.D. Thesis, Case Western Reserve University, Cleveland, OH, 2000
41. R. Busch, Y.J. Kim, W.L. Johnson: J. Appl. Phys., 1995, vol. 77, pp. 4039–4310.1063/1.359485 ↗
42. J.J. Lewandowski, M. Shazly, A.S. Nouri: Scripta Mater., 2006, vol. 54, pp. 337–4110.1016/j.scriptamat.2005.10.010 ↗
43. T.G. Nieh, C. Schuh, J. Wadsworth, Y. Li: Intermetallics, 2002, vol. 10, pp. 1177–8210.1016/S0966-9795(02)00146-2 ↗
44. ASTM E8-04, Standard Test Methods for Tension Testing of Metallic Materials, ASTM, Philadelphia, PA, 2004, vol. E8-04
45. G.E. Dieter. The Hardness Test: Mechanical Metallurgy, McGraw-Hill, New York, NY, 1986, p. 330
46. B.C. Ko, P. Wesseling, L.O. Vatamanu, G.S. Shiflet, J.J. Lewandowski: Intermetallics, 2002, vol. 10, pp. 1099–110310.1016/S0966-9795(02)00164-4 ↗
47. J.J. Lewandowski and P. Lowhaphandu: Int. Mater. Rev., 1998, vol. 43 (4), pp. 145–8710.1179/imr.1998.43.4.145 ↗
48. G.W. Scherer: Relaxation in Glass and Composites, Krieger Publishing, Maber, FL, 1992
49. R.K. Gupta: Polymer and Composite Rheology, Marcel Dekker, New York, NY, 200010.1201/9781482273700 ↗
50. J.J. Lewandowski, A.L. Greer: Nat. Mater., 2006, vol. 5, pp. 15–1810.1038/nmat1536 ↗