journal article·2002-05

Elevated temperature strength and room-temperature toughness of directionally solidified Ni-33Al-33Cr-1Mo

J. Daniel Whittenberger, S. V. Raj, Ivan E. Locci, Jonathan A. Salem

Publisher page

Abstract

The eutectic composition Ni-33Al-33Cr-1Mo has been directionally solidified (DS) via a modified Bridgman technique at rates ranging from 7.6 to 508 mm/h to determine if the growth rate affects the mechanical properties. Microstructural examination revealed that all DS rods had grain/cellular microstructures containing alternating plates of NiAl and Cr alloyed with Mo. At slower growth rates (≤12.7 mm/h), the grains had sharp boundaries, while faster growth rates (≥25.4 mm/h) led to cells bounded by intercellular regions. None of the growth conditions resulted in either dendrites or third phases. Compressive testing between 1200 and 1400 K indicated that alloys DS at rates between 25.4 and 254 mm/h possessed the best strengths, while room-temperature toughness exhibited a plateau of about 16 MPa√m for growth rates between 12.7 and 127 mm/h. Thus, a growth rate of 127 mm/h represents the best combination of fast processing and mechanical properties for this system.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · High-Temperature Coating Behaviors · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. J.L. Walter and H.E. Cline: Metall. Trans., 1970, vol. 1, pp. 1221–29.10.1007/BF02900234 ↗
2. D.R. Johnson, X.F. Chen, B.F. Oliver, R.D. Noebe, and J.D. Whittenberger: Intermetallics, 1995, vol. 3, pp. 99–113.10.1016/0966-9795(95)92674-O ↗
3. J.M. Yang, S.M. Jeng, K. Bain, and R.A. Amato: Acta Mater., 1997, vol. 45, pp. 295–305.10.1016/S1359-6454(96)00124-3 ↗
4. J.D. Whittenberger, S.V. Raj, I.E. Locci, and J.A. Salem: Intermetallics, 1999, vol. 7, pp. 1159–68.10.1016/S0966-9795(99)00023-0 ↗
5. J.D. Cotton, R.D. Noebe, and M.J. Kaufman: Structural Intermetallics, R. Darolia, J.J. Lewandowski, C.T. Liu, P.L. Martin, D.B. Miracle, and M.V. Nathal, eds., TMS, Warrendale, PA, 1993, pp. 513–22.
6. H.E. Cline and J.L. Walter: Metall. Trans., 1970, vol. 1, pp. 2907–17.10.1007/BF03037830 ↗
7. S.M. Joslin: Ph.D. Thesis, The University of Tennessee, Knoxville, TN, 1995.
8. J.M. Yang: JOM, 1997, vol. 49 (8), pp. 40–43.10.1007/BF02914401 ↗
9. J.D. Whittenberger, R.D. Noebe, D.R. Johnson, and B.F. Oliver: Intermetallics, 1997, vol. 5, pp. 173–84.10.1016/S0966-9795(96)00078-7 ↗
10. S.V. Raj, I.E. Locci, and J.D. Whittenberger: Creep Behavior of Advanced Materials for the 21st Century, R.S. Mishra, A.K. Mukherjee, and K. Linga Murty, eds., TMS, Warrendale, PA, 1999, pp. 295–310.
11. J. Daniel Whittenberger, S.V. Raj, and Ivan E. Locci: MRS paper, MRS, Pittsburgh, PA, 2001
12. “Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials,” Test Method E 399-90, Annual Book of ASTM Standards, 03.01, ASTM, West Conshohocken, PA, 1990.
13. J.A. Salem, L.J. Ghosn, and M.G. Jenkins: Ceram. Eng. Sci. Proc., 1998, vol. 19, pp. 587–94.10.1002/9780470294482.ch66 ↗
14. “Standard Test Method for Fracture Toughness of Advanced Ceramics,” Test Method PS070, Annual Book of ASTM Standards, 15.01 ASTM, West Conshohocken, PA, 1998.
15. S.V. Raj and I.E. Locci: Intermetallics, 2001, vol. 9, pp. 217–27.10.1016/S0966-9795(00)00128-X ↗
16. H.E. Cline, J.L. Walter, E. Lifshin, and R.R. Russell: Metall. Trans., 1971, vol. 2, pp. 189–94.10.1007/BF02662656 ↗
17. R.D. Noebe, R.R. Bowman, and M.V. Nathal: Int. Mater. Rev., 1993, vol. 38, pp. 193–232.10.1179/imr.1993.38.4.193 ↗
18. A. Misra, Z.L. Zu, R. Gabala, R.D. Noebe, and B.F. Oliver: Structural Intermetallics, M.V. Nathal, R. Darolia, C.T. Liu, P.L. Martin, D.B. Miracle, R. Wagner, and M. Yamaguchi, eds., TMS, Warrendale, PA, 1997, pp. 673–82.
19. T.M. Pollock and D. Kolluru: Micromechanics of Advanced Materials, S.N.G. Chu, P.K. Law, R.J. Arsenault, K. Sadananda, K.S. Chan, W.W. Gerberich, C.C. Chau, and T.M. Kung, TMS, Warrendale, PA, 1995, pp. 205–12.
20. J. Daniel Whittenberger, S.V. Raj, and I.E. Locci: Creep Deformation: Fundamentals and Applications, R.S. Mishra, J.C. Earthman, and S.V. Raj, eds., TMS, Warrendale, PA, 2002 pp. 331–41.
21. K.R. Forbes, U. Glatzel, R. Darolia, and W.D. Nix: in High Temperature Ordered Intermetallics—V, I. Baker, R. Darolia, J.D. Whittenberger, and M.H. Yoo, eds., Materials Research Society, Pittsburgh, PA, 1993, vol. 288, pp. 45–57.
22. J.D. Whittenberger, I.E. Locci, Ram Darolia, and R. Bowman: Mater. Sci. Eng., A, 1999, vol. A268, pp. 165–83.10.1016/S0921-5093(99)00071-4 ↗
23. J.R. Stephens and W.D. Klopp: J. Less-Common Met., 1972, vol. 27, pp. 87–94.10.1016/0022-5088(72)90108-7 ↗
24. J. Daniel Whittenberger, Beverly Aikin, and Jon Salem: unpublished research.
25. S.V. Raj and G.M. Phaar: Mater. Sci. Eng., 1986, vol. 81, pp. 217–37.10.1016/0025-5416(86)90265-X ↗
26. O.D. Sherby, R.H. Klundt, and A.K. Miller: Metall. Trans. A, 1977, vol. 8A, pp. 843–50.10.1007/BF02661565 ↗
27. J.D. Whittenberger: J. Mater. Sci., 1987, vol. 22, pp. 394–402.10.1007/BF01160744 ↗
28. J.D. Whittenberger, R.D. Noebe, and A. Garg: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 3170–80.10.1007/BF02663867 ↗
29. D.V. Kolluru and T.M. Pollock: Acta Mater., 1998, vol. 46, pp. 2859–76.10.1016/S1359-6454(97)00454-0 ↗
30. J.A. Jimenez, S. Klaus, M. Carsi, O.A. Ruano, and G. Frommeyer: Acta Mater., 1999, vol. 47, pp. 3655–62.10.1016/S1359-6454(99)00218-9 ↗