Mechanical Tensioning of High-Strength Aluminum Alloy Friction Stir Welds
Source abstract
Abstract
The extent to which in-situ global mechanical tensioning (GMT) can be used to modify the residual stress state in friction stir (FS) welds is investigated in this article. Residual stress distributions have been determined by synchrotron X-ray and neutron diffraction for four sets of FS welds in high-strength AA7449-W51 and lithium containing AA2199-T8 aerospace aluminum alloys subjected to a systematic range of GMT levels. For the cases studied, the results indicate that the level of residual stresses present in the as-welded state is a function of the alloy. The rate of residual stress reduction brought about by GMT, however, is basically alloy independent; indeed, it is essentially linear with respect to the GMT load, so that the tensioning required to reduce the weld stresses to zero can be calculated directly from the stresses present in the untensioned case. For thin plates, proximity to the yield stress in the hot-softened zone means that a guideline rule is that 1 MPa of tensioning during welding reduces the tensile stress by approximately 1 MPa. The GMT was found to be less effective at greater depths in thick plates. Furthermore, a reduction in bending distortion and an increase in angular distortion was observed with increased GMT, while no effects on the weld microstructure and hardness were observed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. M.N. James, D.J. Hughes, Z. Chen, H. Lombard, D.G. Hattingh, D. Asquith, J.R. Yates, P.J. Webster: Eng. Fail. Anal., 2007, vol. 14, pp. 384–9510.1016/j.engfailanal.2006.02.011 ↗
2. P.J. Withers: Rep. Prog. Phys., 2007, vol. 70, pp. 2211–6410.1088/0034-4885/70/12/R04 ↗
3. M.J. Peel, A. Steuwer, M. Preuss, P. Withers: Acta Mater., 2003, vol. 51, pp. 4791–480110.1016/S1359-6454(03)00319-7 ↗
4. C.D. Donne, E. Lima, J. Wegener, A. Pyzalla, and T. Buslaps: 3rd Int. Symp. FSW, TWI, Kobe, Japan, 2001
5. L.D. Oosterkamp, P.J. Webster, P.A. Browne, G.B.M. Vaughan, P.J. Withers: Mater. Sci. Forum, 2000, vols. 347–349, pp. 677–83
6. P.J. Webster, L.D. Oosterkamp, P.A. Browne, D.J. Hughes, W.P. Kang, P.J. Withers, G.B.M. Vaughan: J. Strain Anal. Eng. Des., 2001, vol. 36, pp. 61–7010.1243/0309324011512612 ↗
7. M.A. Sutton, A.P. Reynolds, D.Q. Wang, C.R. Hubbard: J. Eng. Mater. Technol., 2002, vol. 124, pp. 215–2110.1115/1.1429639 ↗
8. A. Steuwer, M.J. Peel, P.J. Withers: Mater. Sci. Eng., A, 2006, vol. 441, pp. 187–9610.1016/j.msea.2006.08.012 ↗
9. K. Masubuchi: Welds, Encyclopedia of Materials: Science and Technology, Elsevier Science Ltd., Oxford, United Kingdom, 2003, pp. 8121–26
10. K. Masubuchi: Analysis of Welded Structures, Pergamon Press, Oxford, United Kingdom, 1980
11. P.L. Threadgill, A.J. Leonard, H.R. Shercliff, and P.J. Withers: International Materials Reviews, 2008, in press
12. X.L. Wang, Z. Feng, S.A. David, S. Spooner, and C.R. Hubbard: 6th Int. Conf. Residual Stress, IOM Communications, Oxford, United Kingdom, 2000, vol. 2, pp. 1408–14
13. S.R. Bhide, P. Michaleris, M. Posada, J. DeLoach: Weld. J., 2006, vol. 85, pp. 189–95
14. P. Staron, M. Kocak, S.W. Williams, A. Wescott: Physica B, 2004, vol. 350, pp. E491–E49310.1016/j.physb.2004.03.128 ↗
15. D.A. Price, C.J. Harrison, S.W. Williams, A. Wescott, A. Johnson, J. Gabzdyl, M. Smith, and M. Rahim: BAe Systems Report No. JS 15232, BAE Systems, London, UK, 2004
16. D.A. Price, S.W. Williams, A. Wescott, C.J.C. Harrison, A. Rezai, A. Steuwer, M. Peel, P. Staron, M. Kocak: Sci. Technol. Weld. Join., 2007, vol. 12, pp. 620–3310.1179/174329307X213864 ↗
17. J. Altenkirch, A. Steuwer, M. Peel, D.G. Richards, P.J. Withers: Mater. Sci. Eng., A, 2008, vol. 488, pp. 16–2410.1016/j.msea.2007.10.055 ↗
18. D.G. Richards, P.B. Prangnell, S.W. Williams, P.J. Withers: Mater. Sci. Eng., A, 2008, vol. 489, pp. 351–6210.1016/j.msea.2007.12.042 ↗
19. S.W. Wen, S.W. Williams, S.A. Morgan, A. Wescott, and M. Poad: Sci. Technol. Weld. Joint., 2008, in press
20. J. Altenkirch, A. Steuwer, P.J. Withers, S.W. Williams, M. Poad, and S.W. Wen: Sci. Technol. Weld. Joint., 2008, unpublished research
21. P. Michaleris, J. Dantzig, D. Tortorelli: Weld. Res. Suppl., 1999, vol. 11, pp. 361–66
22. E.M. van der Aa, M.J.M. Hermans, I.M. Richardson, N.M. van der Pers, R. Delhez: Residual Stresses VII, 2006, vols. 524–525, pp. 479–84
23. V. Hauk: Structural and Residual Stress Analysis by Nondestructive Methods, Elsevier, Amsterdam, 1997
24. A.C. Larson and R.B. Von Dreele: General Structure Analysis System (GSAS), Los Alamos National Laboratory Report LAUR 86-748, Los Alamos National Laboratory, Los Alamos, NM, 2000, http://www.ccp14.ac.uk/ccp/ccp14/ftp-mirror/gsas/public/gsas/manual/GSASManual.pdf.
25. T. Pirling, G. Bruno, P.J. Withers: Mater. Sci. Eng., A, 2006, vol. 437A, pp. 139–4410.1016/j.msea.2006.04.083 ↗
26. Large Array Manipulation Program, http://www.ill.fr/data_treat/lamp/lamp.html
27. A. Steuwer, M. Dumont, M. Peel, M. Preuss, P.J. Withers: Acta Mater., 2007, vol. 55, pp. 4111–2010.1016/j.actamat.2007.01.024 ↗
28. P.J. Withers, M. Preuss, A. Steuwer, J.W.L. Pang: J. Appl. Crystallogr., 2007, vol. 40, pp. 891–90410.1107/S0021889807030269 ↗
29. I.C. Noyan and J.B. Cohen: Residual Stress: Measurement by Diffraction and Interpretation, Springer-Verlag, New York, NY, 1987
30. G.A. Webster, ed., “ISO/TTA3, Polycrystalline Materials—Determination of Residual Stress by Neutron Diffraction,” Technol. Trends Assess., 2001, vol. 3
31. M.R. Daymond, M.A.M. Bourke, R.B.V. Dreele, B. Clausen, T. Lorentzen: J. Appl. Phys., 1997, vol. 82, pp. 1554–6210.1063/1.365956 ↗
32. J.W.L. Pang, T.M. Holden, T.E. Mason: Acta Mater., 1998, vol. 46, p. 150310.1016/S1359-6454(97)00369-8 ↗
33. ASM Handbook, vol. 9, Metallography and Microstructures, ASM INTERNATIONAL, Materials Park, OH, 2001
34. M.M. Attallah, C.L. Davis, M. Strangwood: Sci. Technol. Weld. Joining, 2007, vol. 12, pp. 361–6910.1179/174329307X164238 ↗
35. M. James, M.W. Mahoney, and D. Waldron: 1st Int. Symp. FSW, TWI, Thousand Oaks, CA, 1999
36. L.E. Murr, Y. Li, E.A. Trillo, R.D. Flores, J.C. McClure: J. Mater. Process. Manuf. Sci., 1998, vol. 7, pp. 145–6110.1106/X2AA-1046-N9MX-PN69 ↗
37. M.W. Mahoney, C.G. Rhodes, J.G. Flintoff, R.A. Spurling, W.H. Bingel: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1955–6410.1007/s11661-998-0021-5 ↗
38. K.A.A. Hassan, A.F. Norman, D.A. Price, P.B. Prangnell: Acta Mater., 2003, vol. 51, pp. 1923–3610.1016/S1359-6454(02)00598-0 ↗
39. M. Dumont, A. Steuwer, A. Deschamps, M. Peel, P.J. Withers: Acta Mater., 2006, vol. 54, pp. 4793–480110.1016/j.actamat.2006.06.015 ↗
40. P. Gomiero, F. Livet, Y. Brechet, F. Louchet: Acta Metall., 1992, vol. 40, pp. 847–5510.1016/0956-7151(92)90027-C ↗