journal article·2003-05

Effect of rolling temperature on the deformation and recrystallization textures of warm-rolled steels

Mohammad R. Toroghinejad, Fakhraddin Ashrafizadeh, Abbas Najafizadeh, Alan O. Humphreys, Dongsheng Liu, John J. Jonas

Publisher page

Abstract

Warm-rolling trials were carried out on three interstitial-free (IF) steels (stabilized with either niobium or titanium), an extralow-carbon (ELC) steel, and an experimental low-carbon chromium (LC Cr) material at temperatures between 440 °C and 850 °C. The influence of rolling temperature on their as-rolled microstructures and deformation and recrystallization textures was investigated. Also, the effect of coiling simulation and degree of rolling reduction on the r values of some of these materials was examined. In-grain shear bands were evident in all as-rolled microstructures, but their sensitivity to deformation temperature varied between steels. Shear bands of moderate intensity were formed in the IF steels across all temperatures. In the ELC material, intense shear bands were formed at low rolling temperatures, but at higher temperatures, this intensity was drastically reduced. The development of shear bands at the higher rolling temperatures was significantly enhanced by alloying with chromium. The deformation textures produced were typical of rolled ferrite materials. The intensity of this texture increased markedly with temperature for the ELC grade. Conversely, the intensity of the recrystallization texture decreased with increasing temperature. The addition of chromium was found to strengthen the {111} component and, hence, the formability. The sharpness of both the deformation and recrystallization textures of the IF steels was relatively unaffected by rolling temperature. These differences are attributed to the intensity and frequency of shear-band formation and the dynamic strain-aging (DSA) behaviors of the various materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. J.J. Jonas: Proc. Processing & Manufacturing of Advanced Materials, THERMEC ’2000, T. Chandra, K. Higashi, C. Suryanarayana, and C. Tome, eds., Elsevier Science, U.K., 2000.
2. M.R. Barnett and J.J. Jonas: Iron Steel Inst. Jpn. Int., 1999, vol. 39, pp. 856–73.10.2355/isijinternational.39.856 ↗
3. M.R. Barnett and J.J. Jonas: Iron Steel Inst. Jpn. Int., 1997, vol. 37, pp. 697–705.10.2355/isijinternational.37.697 ↗
4. M.R. Barnett: Iron Steel Inst. Jpn. Int., 1998, vol. 38, pp. 78–85.10.2355/isijinternational.38.78 ↗
5. M.R. Barnett: Proc. Materials ’98, M. Ferry, ed., IMEA, Wollongong, Australia, 1998, pp. 167–72.
6. J. Glen: J. Iron Steel Inst., 1957, pp. 21–48.
7. M.R. Barnett: in Modern LC and ULC Sheet Steels for Cold Forming: Processing and Properties, W. Bleck, ed., Verlag Mainz, Aachen, 1998, pp. 61–72.
8. T. Sakai, Y. Saito, and K. Kato: Trans. Iron Steel Inst. Jpn., 1988, vol. 28, pp. 1036–42.10.2355/isijinternational1966.28.1036 ↗
9. H.J. Bunge: Texture Analysis in Materials Science, Butterworth and Co., London, 1982.
10. H.J. Bunge: Z. Metallkd., 1965, vol. 56, pp. 872–74.
11. L. Seidal, M. Holscher, and K. Lücke: Text. Microstr., 1989, vol. 11, pp. 171–85.10.1155/TSM.11.171 ↗
12. U. von Schlippenbach, F. Emren, and K. Lücke: Acta Metall., 1986, vol. 34, pp. 1289–1301.10.1016/0001-6160(86)90015-5 ↗
13. J. Savoie: Texture Menu Software, McGill University, Montreal, Internal Report, 1994.
14. D. Daniel and J.J. Jonas: Metall. Trans. A, 1990, vol. 21A, pp. 331–43.10.1007/BF02782413 ↗
15. D. Liu, A.O. Humphreys, M.R. Toroghinezhad, and J.J. Jonas: Iron Steel Inst. Jpn. 751–59.
16. W.B. Hutchinson, K.-I. Nilson, and J. Hirsch: Metallurgy of Vacuum-Degassed Steel Products, R. Pradhan, ed., TMS, Warrendale, PA, 1990, pp. 109–25.
17. T. Haratani, W.B. Hutchinson, I.L. Dillamore, and P. Bate: Met. Sci., 1984, vol. 18, pp. 57–65.10.1016/0036-9748(84)90089-9 ↗
18. M.R. Barnett and L. Kestens: Text. Microstr., 2000, vol. 34, pp. 1–22.10.1155/TSM.34.1 ↗
19. J.J. Jonas: in Modern LC and ULC Sheet Steels for Cold Forming: Processing and Properties, W. Bleck, ed., Verlag Mainz, Aachen, 1998, pp. 73–84.
20. A.O. Humphreys, D. Liu, M.R. Toroghinezhad, E. Essadiqi, and J.J. Jonas: Mater. Sci. Technol., in press.
21. M.R. Barnett: in Thermomechanical Processing of Steel; COM 2000, S. Yue and E. Essadiqi, eds., Met. Soc. Montreal, 2000, pp. 265–77.
22. J.J. Jonas: in IF Steels 2000 Proc., ISS, Pittsburgh, PA, 2000, pp. 233–45.
23. R.E. Hook and H. Nyo: Metall. Trans. A., 1975, vol. 6A, pp. 1443–51.10.1007/BF02641936 ↗
24. D. Vanderschueren, N. Yoshinaga, and K. Koyama: Iron Steel Inst. Jpn. Int., 1996, vol. 36, 1046–54.10.2355/isijinternational.36.1046 ↗
25. R.K. Ray, J.J. Jonas, and R.E. Hook: Int. Mater. Rev., 1994, vol. 39, pp. 129–72.10.1179/imr.1994.39.4.129 ↗
26. K. Narita: Trans. Iron Steel Inst. Jpn., 1975, vol. 15, pp. 145–52.10.2355/isijinternational1966.15.145 ↗
27. K.J. Irvine, F.B. Pickering, and T. Gladman: J. Iron Steel Inst., 1967, vol. 205, pp. 161–82.
28. S. Matsuda and N. Okumura: Trans. Iron Steel Inst. Jpn., 1998, vol. 18, pp. 198–205.10.2355/isijinternational1966.18.198 ↗
29. M.R. Barnett: Steel Res., 2000, vol. 71, pp. 295–302.10.1002/srin.200001232 ↗
30. S. Satoh, T. Obara, and M. Nishida: Trans. Iron Steel Inst. Jpn., 1984, vol. 24, pp. 838–46.10.2355/isijinternational1966.24.838 ↗