journal article·2000-12

Relation between microstructure, composition, and hot cracking in Ti-stabilized austenitic stainless steel weldments

V. Shankar, T. P. S. Gill, S. L. Mannan, A. L. E. Terrance, S. Sundaresan

Publisher page

Abstract

A stabilized, fully austenitic alloy D9, a 15Cr-15Ni-2Mo stainless steel with a titanium addition corresponding to UNS 38660, is a candidate material for the fuel-clad and wrapper applications of the Prototype Fast Breeder Reactor (PFBR). The fully austenitic microstructure and the presence of titanium in this alloy lead to high susceptibility to hot cracking during welding. The fusion-zone and the heat-affected zone (HAZ) cracking susceptibility of alloy D9 was studied at three titanium levels, 0.22, 0.32, and 0.42 pct, all other elements remaining constant. The longitudinal and transverse Varestraint (Transvarestraint) hot-cracking tests were used to evaluate fusion-zone and HAZ cracking. The results showed that titanium increases cracking in the fusion zone by 15 to 20 pct in the range of Ti levels studied. The microanalysis of fusion-zone hot cracks using electron probe microanalysis (EPMA) showed an enrichment of Ti, C, N, and S along cracks and in the interdendritic regions. The corresponding phases were identified as TiC, TiC0.3N0.7, and the carbosulfides Ti2CS and Ti4C2S2, which are believed to form eutectics with austenite to produce cracking. The amounts of these phases increased with increasing Ti content. In the HAZ, a similar relation between titanium level and cracking was found. The comparison of the weldability of the D9 with an FA mode type 321 revealed that Ti-bearing eutectics were responsible for a high degree of cracking irrespective of the solidification mode. The results show that in the D9, the ratio of Ti to C and N must be controlled to minimize cracking.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. N.N. Prokhorov and N.N. Prokhorov: Trans. JWS, 1971, vol. 2 (2), pp. 109–17.
2. F. Matsuda, S. Katayama, and Y. Arata: Trans. JWRI, 1981, vol. 10 (2), pp. 73–84.
3. M.J. Cieslak: Welding J., 1991, vol. 71 (2), pp. 49s-56s.
4. G.A. Knorovsky, M.J. Cieslak, T.J. Headley, A.D. Romig, Jr., and W.F. Hammetter: Met. Trans. A, 1989, vol. 10, pp. 2149–158.10.1007/BF02650300 ↗
5. C.D. Lundin, W.T. DeLong, and D.F. Spond: Welding J., 1975, vol. 54, pp. 241s-246s.
6. J.C. Lippold: Welding J., 1983, vol. 62, pp. 1s-11s.
7. J.A. Brooks: Welding J., 1974, vol. 53, pp. 517s-523s.
8. E. Folkhard: in Welding Metallurgy of Stainless Steels, Springer-Verlag, New York, NY, 1988.10.1007/978-3-7091-8965-8 ↗
9. L. Egnell and W.M. May: Proc. Conf. Welding of Creep Resistant Steels, The Welding Institute, London, 1970, pp. 144–51.
10. T.M. Cullen and J.W. Freeman: J. Eng. Power, 1963, vol. 85, pp. 151–64.10.1115/1.3675237 ↗
11. R.W. Messler Jr. and L. Li: Sci. Technol. Welding Joining, 1997, vol. 2 (2), pp. 43–52.10.1179/stw.1997.2.2.43 ↗
12. J.J. Pepe and W.F. Savage: Welding J., 1970, vol. 49, pp. 545s-553s.
13. F. Matsuda, S. Katayama, and Y. Arata: Trans. JWRI, 1983, vol. 12 (2), pp. 87–92.
14. V. Shankar, T.P.S. Gill, S.L. Mannan, and S. Sundaresan: Sci. Technol. Welding Joining, 1998, vol. 3 (1), pp. 17–24.10.1179/stw.1998.3.1.17 ↗
15. C.D. Lundin, R. Menon, C.H. Lee, and V. Osorio: Welding Research—the State of the Art, Proc. JDC University Symp., Toronto, ASM, Metals Park, OH, 1985, pp. 33–42.
16. C.D. Lundin, C.H. Lee, R. Menon, and V. Osorio: Weld. J., 1988, vol. 67 (2), pp. 35s-46s.
17. T.P.S. Gill and J.B. Gnanamoorthy: J. Mater. Sci., 1982, vol. 17, p. 1513.10.1007/BF00752268 ↗
18. T.P.S. Gill and J.B. Gnanamoorthy: Trans. Ind. Inst. Met., 1983, vol. 36, p. 269.
19. V. Shankar, T.P.S. Gill, S.L. Mannan, and S. Sundaresan: Sci. Technol. Welding and Joining, 2000, vol. 5 (2), pp. 91–97.10.1179/136217100101538074 ↗
20. F. Matsuda: Advances in Welding Metallurgy, AWS, JWS, and JWES, Miami, FL, 1990 pp. 19–35.
21. Y. Arata, F. Matsuda, and S. Katayama: Trans. JWRI, 1977, vol. 6 (1), pp. 105–16.
22. V. Shankar: Ph.D. Thesis, Indian Institute of Technology, Madras, 2000.
23. C.D. Lundin, C.H. Lee, and C.Y.P. Qiao: Welding J., 1993, vol. 72 (7), pp. 321s-328s.
24. T.B. Massalski: Alloy Phase Diagrams, ASM, Metals Park, OH, 1996.
25. F. Matsuda, H. Nakagawa, and J.-B. Lee: Trans. JWRI, 1989, vol. 18 (1), pp. 107–17.
26. H.J. Schuller: Arch. Eisenhuttenwes., 1963, vol. 34, pp. 61–68.
27. Y. Nakao, H. Ohshige, S. Koga, H. Nishihara, and J. Sugitani: J. JWS, 1982, vol. 51 (12), pp. 989–95.
28. S.C. Fegan, T.Z. Kattamis, J.E. Morral, and A.K. Bhambri: J. Mater. Sci., 1975, vol. 10, pp. 1266–70.10.1007/BF00541420 ↗
29. W. Kestemich: Phil. Mag., 1985, vol. 52 (4), pp. 533–48.10.1080/01418618508237645 ↗
30. C.J. Long and W.T. DeLong: Welding J., 1973, vol. 53 (7), pp. 281s-297s.
31. R. Sandhya: IGCAR, Kalpakkam, unpublished research.
32. F. Matsuda, S. Katayama, and Y. Arata: Trans. JWRI, 1983, vol. 12 (2), pp. 87–92.
33. F. Matsuda, S. Katayama, and Y. Arata: Trans. JWRI, 1981, vol. 10 (2), pp. 73–84.
34. W. Lin, J.C. Lippold, and W.A. Baeslack III: Welding J., 1993, vol. 72, pp. 135s-153s.
35. V. Shankar, T.P.S. Gill, S.L. Mannan, and S. Sundaresan: Welding J., 1998, vol. 77 (5), pp. 193s-201s.
36. V.P. Kujanpaa, S.A. David, and C.L. White: Welding J., 1987, vol. 66 (8), pp. 221s-228s.
37. J.C. Lippold, W.A. Baeslack III, and I. Varol: Welding J., 1992, vol. 71, pp. 1s-14s.
38. V. Shankar, T.P.S. Gill, S.L. Mannan, and S. Sundaresan: Sci. Technol. Welding Joining, 1998, vol. 3 (1), pp. 17–24.10.1179/stw.1998.3.1.17 ↗