journal article·2002-11

Anisotropy of intermetallic particle cracking damage evolution in an Al-Mg-Si base wrought aluminum alloy under uniaxial compression

H. Agarwal, A. M. Gokhale, S. Graham, M. F. Horstemeyer

Publisher page

Abstract

Particle cracking is an important damage mode in numerous engineering alloys having anisotropic microstructures. In this contribution, cracking of anisotropic Fe-rich intermetallic particles in an extruded 6061 (T651) Al-alloy is quantitatively characterized as a function of compressive strain for two loading directions. The Fe-rich intermetallic particles rotate when a compressive load is applied parallel to the extrusion direction, which in turn affects the particle cracking process. At low compressive strains, the number fraction of cracked Fe-rich particles is higher in specimens loaded perpendicular to the extrusion axis as compared to that in specimens loaded parallel to the extrusion axis. However, the reverse is true at the high strain levels. These differences in damage evolution are explained on the basis of particle rotations and microstructural anisotropy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. M.F. Horstmeyer and A.M. Gokhale: Int. J. Solids Struct., 1999, vol. 36, pp. 5029–55.10.1016/S0020-7683(98)00239-X ↗
2. M.F. Horstemeyer, J. Lathrop, A.M. Gokhale, and M. Dighe: Theor. Appl. Fract. Mech., 2000, vol. 33, pp. 31–47.10.1016/S0167-8442(99)00049-X ↗
3. Jien-Wei Yeh and Wen-Pin Liu: Metall. Trans. A, 1996, vol. 27A, pp. 3558–69.10.1007/BF02595447 ↗
4. R. Doglione, J.L. Douziech, C. Berdin, and D. Francois: Mater. Sci. Forum, 1996, pp. 130–39.
5. E.N. Pan, C.S. Lin, and C.R. Loper: Am. Foundrymen Soc. Trans., 1990, vol. 98, pp. 735–46.
6. J. Gurland and J. Plateau: Trans. ASM, 1963, vol. 56, pp. 442–52.
7. A.S. Argon, J. Im, and R. Safoglu: Metall. Trans. A, 1975, vol. 6A, pp. 825–37.10.1007/BF02672306 ↗
8. J. Gurland: Acta Metall., 1972, vol. 20, pp. 735–41.10.1016/0001-6160(72)90102-2 ↗
9. J.L. Maloney and W.M. Garrison, Jr.: Scripta Metall., 1989, vol. 23, pp. 2097–2100.10.1016/0036-9748(89)90238-X ↗
10. T.B. Cox and J.R. Low: Metall. Trans., vol. 5, pp. 1457–70.10.1007/BF02646633 ↗
11. A. Gangalee and J. Gurland: Trans. TMS-AIME, 1967, vol. 239, pp. 269–72.
12. M.D. Dighe: Master’s Thesis, Teorgia Institute of Technology, Atlanta, GA, 1999.
13. M.D. Dighe, A.M. Gokhale, and M.F. Horstemeyer: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 555–65.10.1007/s11661-002-0117-2 ↗
14. M.D. Dighe, A.M. Gokhale, and M.F. Horstemeyer: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 905–08.
15. M.D. Dighe, A.M. Gokhale, and M.F. Horstemeyer: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 1725–31.10.1007/s11661-998-0331-7 ↗
16. P. Louis and A.M. Gokhale: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 1449–54.10.1007/BF02647595 ↗
17. C.H. Caceres and J.R. Griffiths: Acta Mater., 1996, vol. 44, pp. 25–33.10.1016/1359-6454(95)00172-8 ↗
18. G.B. Jeffery: Proc. R. Soc., London, 1923, vol. A102, pp. 161–79.
19. S. Prager: Trans. Soc. Rheology, 1957, vol. 1, pp. 53–62.10.1122/1.548808 ↗
20. J.L. Erickson: Arch. Rat. Mech. Anal., 1959, vol. 4, pp. 231–37.10.1007/BF00281389 ↗
21. G.L. Hand: J. Fluid Mech., 1962, vol. 33, pp. 33–46.10.1017/S0022112062000476 ↗
22. C. Schuh and D.C. Dunand: Int. J. Plasticity, 2001, vol. 17, pp. 317–40.10.1016/S0749-6419(00)00038-3 ↗
23. Arun Kumar Balasundaram: Master’s Thesis, Georgia Institute of Technology, Atlanta, GA, 2001.