journal article·2008-01

Improved Creep Behavior of Ferritic-Martensitic Alloy T91 by Subgrain Boundary Density Enhancement

G. Gupta, Gary S. Was

Publisher page

Abstract

The objective of this study was to increase the creep strength of the ferritic-martensitic (F-M) alloy T91 by enhancing the subgrain boundary density. A thermomechanical treatment involving a 5 pct compression treatment, followed by an annealing treatment at 1050 °C for 1 hour, then air cooling, and a tempering treatment at 800 °C for 0.66 hours, then another air cooling, resulted in an increase in the subgrain boundary density of ∼39 pct, without altering any of the other microstructural features. Creep tests were conducted on both as-received (AR) and subgrain-boundary-enhanced (SGBE) conditions of the F-M alloy T91, over a temperature range of 500 °C to 600 °C and in the stress range of 150 to 255 MPa in argon. The T91-AR exhibited a higher creep rate than the T91-SGBE by a factor of ∼2.0 to 8.0. The ratio of time to rupture for the T91-SGBE compared to the T91-AR varied from 1.0 to 5.0. In general, higher ratios were seen at higher stresses. Creep behavior was analyzed on the basis of the Orowan equation, according to which creep rate is controlled by the mobile dislocation density and dislocation velocity. Internal stress calculations performed on both conditions showed a higher internal stress in the T91-SGBE by ∼10 MPa. Analysis of the sources of internal stress suggest that the higher value for the SGBE condition is due to subgrain boundary density enhancement. The SGBE condition exhibited a temperature-increment benefit of between 8 °C and 26 °C, such that the creep strength realized for the T91-SGBE was similar to that realized for the T91-AR, but at a higher temperature. The temperature-increment benefit increased exponentially with applied stress but less so with temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. G. Gupta and G.S. Was: J. ASTM Int., 2005, vol. 2 (3)10.1520/JAI12355 ↗
2. S. Spigarelli, E. Cerrie, P. Bianchi, E. Evangelista: Mater. Sci. Technol., 1999, vol. 15, pp. 1433–4010.1179/026708399101505428 ↗
3. P. Anderson, T. Bellgardt, F.L. Jones: Mater. Sci. Technol., 2003, vol. 19, pp. 207–1310.1179/026708303225009436 ↗
4. P.J. Ennis and A. Czyrska-Filemonowicz: OMMI, 2002, vol. 1 (1)
5. N. Eberle, F.L. Jones: Mater. Sci. Technol., 2003, vol. 19, pp. 214–1810.1179/026708303225010623 ↗
6. A. Fujio: Mater. Sci. Eng., A, 2004, vols. 387–389 (1–2), pp. 565–69
7. G. Eggeler: Acta Metall., 1989, vol. 37 (12), pp. 3225–3410.1016/0001-6160(89)90194-6 ↗
8. F. Abe, T. Horiuchi, M. Taneike, K. Sawada: Mater. Sci. Eng., A, 2004, vol. 378, pp. 299–30310.1016/j.msea.2003.11.073 ↗
9. V. Sklenicka, K. Kucharova, A. Dlouhy, J. Krejci: in Materials for Advanced Power Engineering, D. Coutsouradis et al., eds., Kluwer Academic Publisher, Netherlands, 1994, p. 435
10. G. Gupta, B. Alexandreanu, G.S. Was: Metall. Mater. Trans. A, 2004, vol. 35A (2), pp. 717–1910.1007/s11661-004-0382-3 ↗
11. G. Gupta: Doctoral Thesis, University of Michigan, Ann Arbor, MI, 2007
12. P. Hirsch, A. Howie, R. Nicholson, D.W. Pashley, M.J. Whelan: Electron Microscopy of Thin Crystals, Krieger Publishing Company, Malabar, 1977
13. M.H. Loretto: Electron Beam Analysis of Materials, Chapman and Hall, London, 1994
14. E. Nes, K. Marthinsen, B. Holmedal: Mater. Sci. Technol., 2004, vol. 20, p. 133710.1179/026708304225022250 ↗
15. A. Kostka, K.G. Tak, G. Eggeler: Acta Mater., 2007, vol. 55, pp. 539–5010.1016/j.actamat.2006.08.046 ↗
16. J. Pesicka, R. Kuzel, A. Dronhofer, G. Eggeler: Acta Mater., 2003, vol. 51, pp. 4847–6210.1016/S1359-6454(03)00324-0 ↗
17. J. Pescika, A. Dronhofer, G. Eggeler: Mater. Sci. Eng., A, 2004, vols. 387–389, pp. 176–8010.1016/j.msea.2004.03.080 ↗
18. U.S. Kocks: Prog. Mater Sci., 1975, vol. 19
19. J. Cadek: Creep in Metallic Materials, Elsevier Science Publishing Company, Inc., New York, NY, 1988
20. N. Baluc, R. Schaublin, P. Spatig, and M. Victoria: 21st Int. Symp., ASTM STP 144 1447, M.L. Grossbeck, T.R. Allen, R.G. Lott, and A.S. Kumar, eds., ASTM International, West Conshohocken, PA, 2004
21. F. Dobes, A. Orlova: Mater. Sci. Forum, 2005, vol. 482, pp. 291–9410.4028/www.scientific.net/MSF.482.291 ↗
22. H. Wiedersich: J. Met., 1964, vol. 16, p. 425
23. A. Orlova: Mater. Sci. Eng., A, 2001, vol. A297, pp. 281–8510.1016/S0921-5093(00)01697-X ↗
24. E. Nes, K. Marthinsen, B. Holmedal: Mater. Sci. Technol., 2004, vol. 20, p. 133710.1179/026708304225022250 ↗
25. G. Dimmler: Doctoral Thesis, Graz University of Technology, 2003 (in German)
26. R.L. Fleischer: Acta Metall., 1963, vol. 11, p. 20310.1016/0001-6160(63)90213-X ↗
27. A. Seeger: Proc. 2nd United Nations Int. Conf. on the Peaceful Uses of Atomic Energy, United Nations, New York, NY, 1958, vol. 6, p. 250
28. G.E. Dieter: Mechanical Metallurgy, 2nd ed., McGraw-Hill Book Company, New York, NY, 1981, pp. 166–74
29. G.E. Lucas: J. Nucl. Mater., 1993, vol. 206, pp. 287–30510.1016/0022-3115(93)90129-M ↗
30. R. Schaeublin, D. Gelles, M. Victoria: J. Nucl. Mater., 2002, vols. 307–311, pp. 197–20210.1016/S0022-3115(02)01034-6 ↗
31. S.J. Zinkle: Radiat. Eff. Def. Solids, 1999, vol. 148, p. 37710.1080/10420159908229104 ↗
32. A.J.E. Foreman, M.J. Makin: Can. J. Phys., 1967, vol. 45, p. 51110.1139/p67-044 ↗
33. U.S. Kocks: Physics of Strength and Plasticity, MIT Press, Cambridge, MA, 1969, p. 143
34. S.J. Zinkle, Y. Matsukawa: J. Nucl. Mater., 2004, vols. 329–333, pp. 88–9610.1016/j.jnucmat.2004.04.298 ↗
35. A. Di Gianfrancesco et al.: La Rev. Metall., 2001, pp. 117–2310.1051/metal:2001158 ↗