Fatigue Crack Growth under High Pressure of Gaseous Hydrogen in a 15-5PH Martensitic Stainless Steel: Influence of Pressure and Loading Frequency
Source abstract
Abstract
In this study, the effect of gaseous hydrogen pressure in relation with the loading frequency on the fatigue crack growth behavior of a precipitation-hardened martensitic stainless steel is investigated. It is found that increasing the hydrogen pressure from 0.09 to 9 MPa induces an enhancement of the fatigue crack growth rates. This enhancement is pronounced particularly at higher stress intensity factor amplitudes at 9 MPa. Meanwhile, decreasing the frequency from 20 to 0.2 Hz under 0.9 MPa of hydrogen reveals a significant increase in the crack growth rates that tends to join the curve obtained under 9 MPa at 20 Hz, but with a different cracking mode. However, it is shown that the degradation in fatigue crack growth behavior derives from a complex interaction between the fatigue damage and the amount of hydrogen enriching the crack tip, which is dependent on the hydrogen pressure, loading frequency, and stress intensity factor level. Scanning electron microscope (SEM) observations of the fracture surfaces are used to support the explanations proposed to account for the observed phenomena.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Fatigue and fracture mechanics · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. R.P. Gangloff and R.P. Wei: Metall. Trans. A, 1977, vol. 8, pp. 1043–53.10.1007/BF02667388 ↗
2. C.J. McMahon: Eng. Fract. Mech., 2001, vol. 68, pp. 773–88.10.1016/S0013-7944(00)00124-7 ↗
3. I. Moro, L. Briottet, P. Lemoine, E. Andrieu, C. Blanc, and G. Odemer: Mater. Sci. Eng. A, 2010, vol. 527, pp. 7252–60.10.1016/j.msea.2010.07.027 ↗
4. G. Schuster and C. Altstetter: Metall. Trans. A, 1983, vol. 14A, pp. 2085–90.10.1007/BF02662375 ↗
5. Y. Murakami, T. Kanezaki, Y. Mine, and S. Matsuoka: Metall. Mater. Trans. A, 2008, vol. 39A, pp. 1327–39.10.1007/s11661-008-9506-5 ↗
6. Y.S. Ding, L.W. Tsay, M.F. Chiang, and C. Chen: J. Nucl. Mater., 2009, vol. 385, pp. 538–44.10.1016/j.jnucmat.2008.12.048 ↗
7. R.A. Oriani: Ber. Buns. Phys. Chem. N.F., 1972, vol. 76, pp. 848–57.10.1002/bbpc.19720760864 ↗
8. R.A. Oriani: Ann. Rev. Mater. Sci., 1978, vol. 8, pp. 327–57.10.1146/annurev.ms.08.080178.001551 ↗
9. R.A. Oriani: Corrosion Science: A Retrospective and Current Status in Honor of Robert P Frankenthal, Electrochemical Society Inc, Pennington, NJ, 2002, pp. 385–99.
10. C.D. Beachem: Metall. Trans., 1972, vol. 3, pp. 437–51.10.1007/BF02642048 ↗
11. H.K. Birnbaum: Atomistics of Fracture, Plenum, New York, NY, 1983, pp. 733–65.10.1007/978-1-4613-3500-9_25 ↗
12. H.K. Birnbaum and P. Sofronis: Mater. Sci. Eng. A, 1994, vol. 176, pp. 191–202.10.1016/0921-5093(94)90975-X ↗
13. H.K. Birnbaum and P. Sofronis: Corrosion-Deformation Interactions CDI’96, The Institute of Materials, Nice, France, 1996, pp. 172–95.
14. I.M. Robertson: Eng. Fract. Mech., 2001, vol. 68, pp. 671–92.10.1016/S0013-7944(01)00011-X ↗
15. S.P. Lynch: Hydrogen Effects on Material Behavior and Corrosion Deformation Interactions, TMS, Warrendale, PA, 2003, pp. 449–66.
16. Y. Murakami and R.O. Ritchie: Gaseous Hydrogen Embrittlement of Materials in Energy Technologies: The Problem, its Characterisation and Effects on Particular Alloy Classes, vol. 1. R.P. Gangloff and B. Somerday, eds., Woodhead Publishing Limited, Cambridge, U.K., in press.
17. C. Murray: Metall. Trans. A, 1981, vol. 12A, pp. 2138–41.10.1007/BF02644189 ↗
18. Y. Kondo, M. Kubota, and K. Shimada: Eng. Fract. Mech., 2010, vol. 77, pp. 1963–74.10.1016/j.engfracmech.2010.01.012 ↗
19. J. Mostofi and M. Zamanian: Mater. Perform., 2008, vol. 47, pp. 64–67.
20. S. Castagnet, J.C. Grandidier, M. Comyn, and G. Benoit: Int. J. Hydrogen Energ., 2010, vol. 35, pp. 7633–40.10.1016/j.ijhydene.2010.04.155 ↗
21. Z. Sun, G. Benoit, C. Moriconi, F. Hamon, D. Halm, F. Hamon, and G. Hénaff: Int. J. Hydrogen Energ. 4 th Asian Bio-Hydrogen Symp., 2011, vol. 36, pp. 8641–44.10.1016/j.ijhydene.2011.04.094 ↗
22. A.T. Stewart: Eng. Fract. Mech., 1980, vol. 13, pp. 463–78.10.1016/0013-7944(80)90078-8 ↗
23. R.J. Cooke, P.E. Irving, G.S. Booth, and C.J. Beevers: Eng. Fract. Mech., 1975, vol. 7, pp. 69–77.10.1016/0013-7944(75)90067-3 ↗
24. J.D. Frandsen and H.L. Marcus: Scripta Metall., 1975, vol. 9, pp. 1089–94.10.1016/0036-9748(75)90285-9 ↗
25. G. Hénaff, J. Petit, and B. Bouchet: Int. J. Fatigue, 1992, vol. 14, pp. 211–18.10.1016/0142-1123(92)90002-T ↗
26. H.J. Cialone and J.H. Holbrook: Metall. Trans. A, 1985, vol. 16A, pp. 115–22.10.1007/BF02656719 ↗
27. H.J. Cialone and J.H. Holbrook: Hydrogen Embrittlement: Prevention and Control, ASTM STP 962, L. Raymond, ed., ASTM, West Conshohocken, PA, 1988, pp. 134–52.10.1520/STP45297S ↗
28. R.J. Walter and W.T. Chandler: Effect of Hydrogen on Behavior of Materials, A.W. Thompson and I.M. Bernstein, eds., TMS, Warrendale, PA, 1976, pp. 273–86.
29. T. Michler and J. Naumann: Int. J. Hydrogen Energ. Hyceltec 2009 Conf., 2010, vol. 35, pp. 11373–77.10.1016/j.ijhydene.2010.07.093 ↗
30. K.A. Nibur, B.P. Somerday, C.S. Marchi, D.K. Balch, J.W. Foulk III, M. Dadfarnia, P. Sofronis, and G.A. Hayden: Measurement and Interpretation of Threshold Stress Intensity Factors for Steels in High-Pressure Hydrogen Gas, Sandia Report, SAND2010-4633, Sandia National Laboratories, Albuquerque, NM, 2010.
31. G. Hénaff and J. Petit: Fatigue’96, G. Lutjering and H. Nowack, eds., Pergamon Press, Berlin, Germany, 1996, pp. 715–20.
32. P.K. Liaw, S.J. Hudak Jr., and J.K. Donald: Metall. Trans. A, 1982, vol. 13A, pp. 1633–45.10.1007/BF02644804 ↗
33. P.K. Liaw: Acta Metall., 1985, vol. 33, pp. 1489–1502.10.1016/0001-6160(85)90050-1 ↗
34. S. Matsuoka, H. Tanaka, N. Homma, and Y. Murakami: Int. J. Fract., 2009, vol. 168, pp. 101–12.10.1007/s10704-010-9560-z ↗
35. W.G. Clark: Hydrogen in Metals, I.M. Bernstein and A.W. Thompson, eds., ASM, Materials Park, OH, 1977, pp. 149–62.
36. S.P. Lynch and N.E. Ryan: Second International Congress in Hydrogen in Metals, C.D. Beachem, ed., ASM, Materials Park, OH, 1977, pp. 369–76.
37. J.C.M. Li, R.A. Oriani, and L.S. Darken: Zeit. Phys. Chem. NF, 1966, vol. 49, pp. 271–90.10.1524/zpch.1966.49.3_5.271 ↗
38. J.K. Tien, R.J. Richards, O. Buck, and H.L. Marcus: Scripta Metall., 1975, vol. 9, pp. 1097–1101.10.1016/0036-9748(75)90287-2 ↗
39. H.G. Nelson: Effect of Hydrogen on Behavior of Materials, A.W. Thompson and I.M. Bernstein, eds., The Metallurgical Society of AIME, Moran, WY, 1975, pp. 602–11.
40. P. Fassina, F. Brunella, L. Lazzari, G. Re, L. Vergani, and A. Sciuccati: Procedia Engineering, 11th International Conference on the Mechanical Behavior of Materials (ICM11), 2011, vol. 10, pp. 3345–52.10.1016/j.proeng.2011.04.552 ↗
41. C.S. Marchi and B. Somerday: Technical Reference on Hydrogen Compatibility of Materials, Sandia Report SAND2008-1163, Sandia National Laboratories, Albuquerque, NM, 2008.
42. V. Olden, C. Thaulow, and R. Johnsen: Mater. Des., 2008, vol. 29, pp. 1934–48.10.1016/j.matdes.2008.04.026 ↗
43. N. Saintier, T. Awane, J.M. Olive, S. Matsuoka, and Y. Murakami: Int. J. Hydrogen Energ., 2011, vol. 36, pp. 8630–40.10.1016/j.ijhydene.2011.03.111 ↗
44. P. Bastien and P. Azou: CRH Acad. Sc., 1950, vol. 231, pp. 147–48.
45. S. Fujita: Interscience, 1963, vol. 20, pp. 657–70.
46. J. Hirth: Metall. Trans. A, 1980, vol. 11A, pp. 861–90.10.1007/BF02654700 ↗
47. J.K. Tien, A.W. Thompson, I.M. Bernstein, and R.J. Richards: Metall. Trans. A, 1976, vol. 7A, pp. 821–29.10.1007/BF02644079 ↗
48. A.H.M. Krom, H.J. Maier, R.W.J. Koers, and A. Bakker: Mater. Sci. Eng. A, 1999, vol. 271, pp. 22–30.10.1016/S0921-5093(99)00276-2 ↗
49. A.H.M. Krom, R.W.J. Koers, and A. Bakker: J. Mech. Phys. Solids, 1999, vol. 47, pp. 971–92.10.1016/S0022-5096(98)00064-7 ↗
50. H. Kotake, R. Matsumoto, S. Taketomi, and N. Miyazaki: Int. J. Press. Ves. Pip., 2008, vol. 85, pp. 540–49.10.1016/j.ijpvp.2008.02.002 ↗
51. J.S. Wang: Eng. Fract. Mech., 2001, vol. 68, pp. 647–69.10.1016/S0013-7944(00)00120-X ↗
52. A. Barnoush and H. Vehoff: Corros. Sci., 2008, vol. 50, pp. 259–67.10.1016/j.corsci.2007.05.026 ↗
53. G.M. Pressouyre: Metall. Trans. A, 1979, vol. 12A, pp. 1571–73.10.1007/BF02812023 ↗
54. R.J. Richards, S. Purushothaman, J.K. Tien, J.D. Frandsen, and O. Buck: Metall. Trans. A, 1978, vol. 9A, pp. 1107–11.10.1007/BF02652215 ↗
55. C. Moriconi, G. Henaff, and D. Halm: Proc. Eng., 11 th Int. Conf. on the Mechanical Behavior of Materials (ICM11), vol. 10, 2011, pp. 2657–62.10.1016/j.proeng.2011.04.443 ↗