journal article·2007-12

Crystallography of Fatigue Crack Propagation in Precipitation-Hardened Al-Cu-Mg/Li

YunJo Ro, Sean R. Agnew, Richard P. Gangloff

Publisher page

Abstract

A combined electron backscatter diffraction (EBSD)/stereology method successfully quantifies the orientation of fatigue crack surfaces for Al-Li-Cu and Al-Cu-Mg alloys stressed at low ΔK, in which deformation is localized in slip bands and cracking is highly faceted. The method orients features as small as ∼1 μm in complex microstructures. Vacuum fatigue facets align within 15 deg of up to four variants of {111} slip planes, governed by the distribution of crack tip resolved shear stress. The small fraction of precisely oriented {111} facets suggests that cracking involves complex intraband and multiple-band interface paths. Water vapor and NaCl solution affect a similar dramatic change in the crack path; near-{111} facets are never observed, at odds with mechanisms for H-enhanced slip localization and associated slip band cracking. Rather, two environmental crack facet morphologies, broad flat and repeating step, exhibit a wide range of orientations between {001} and {110}, as governed by crack tip resolved normal stresses. The repetitive stepped facets appear to contain areas parallel to {100}/{110} on the ∼1-μm scale, coupled with surface curvature consistent with a mechanism of discontinuous fatigue crack growth involving H-enhanced {100}/{110} cleavage and intermingled crack tip plasticity. Broad-flat faceted regions are parallel to a variety of planes, consistent with a mechanism combining high crack tip tensile stresses and H trapped at the dislocation structure from cyclic deformation, within 1 μm of the crack tip.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Hydrogen embrittlement and corrosion behaviors in metals · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (82)

Show source-provided references
1. K.T. Venkateswara, Rao R.O. Ritchie: Int. Mater. Rev., 1992, vol. 37 (4) pp. 153–85
2. R.S. Piascik, R.P. Gangloff: Metall. Trans. A, 1993, vol. 24A, pp. 2751–6210.1007/BF02659499 ↗
3. D.C. Slavik, C.P. Blankenship Jr., E.A. Starke Jr., R.P. Gangloff: Metall. Trans. A, 1993, vol. 24A, pp. 1807–1710.1007/BF02657855 ↗
4. D.C. Slavik, R.P. Gangloff: Acta Mater., 1996, vol. 44, pp. 3515–3410.1016/1359-6454(96)00013-4 ↗
5. D.C. Slavik, J.A. Wert, R.P. Gangloff: J. Mater. Res., 1993, vol. 8 (10), pp. 2482–9110.1557/JMR.1993.2482 ↗
6. D. Li, R.P. Gangloff, G.H. Bray, M.V. Glazov, R.J. Rioja: in Advances in the Metallurgy of Aluminum Alloys, M. Tiryakioglu, ed., ASM INTERNATIONAL, Materials Park, OH, 2001, pp. 105–18
7. G.H. Bray, M.V. Glazov, R.J. Rioja, D. Li, R.P. Gangloff: Int. J. Fatigue, 2001, vol. 23, pp. 265–7610.1016/S0142-1123(01)00159-1 ↗
8. J. Petit, J. de Fouquet, G. Henaff: in Handbook on Fatigue Crack Propagation in Metallic Structures, A. Carpinteri, ed., Elsevier, New York, NY, 1994, pp. 1159–120410.1016/B978-0-444-81645-0.50010-X ↗
9. R.P. Gangloff: Fatigue '02, A.F. Blom, ed., Engineering Materials Advisory Services, West Midlands, United Kingdom, 2002, pp. 3401–34
10. Y.J. Ro: Master’s Thesis, University of Virginia, Charlottesville, VA, 2004
11. T.H. Sanders Jr., E.A. Starke Jr.: Acta Metall., 1982, vol. 30, pp. 927–3910.1016/0001-6160(82)90199-7 ↗
12. K.V. Jata, E.A. Starke Jr.: Metall. Trans. A, 1986, vol. 17A, pp. 1011–2610.1007/BF02661267 ↗
13. M. Lewandowska, J. Mizera, J.W. Wyrzykowski: Mater. Charact., 2000, vol. 45, pp. 195–20210.1016/S1044-5803(00)00074-7 ↗
14. A. Brotzu, M. Cavallini, F. Felli, and M. Marchetti: Fatigue in the Presence of Corrosion, RTO AVT Workshop, NATO Report No. RTO-MP-18 (AC/323(AVT)TP/8), Corfu, Greece, 1998, pp. 8-1–8-12
15. N. Ranganathan, F. Adiwijayanto, J. Petit, J.P. Bailon: Acta Metall. Mater., 1995, vol. 43 (3), pp. 1029–3510.1016/0956-7151(94)00301-W ↗
16. N. Ranganathan, S.Q. Li, J.P. Bailon, J. Petit: Mater. Sci. Eng., A, 1994, vol. A187, pp. 37–4210.1016/0921-5093(94)90328-X ↗
17. G.R. Yoder, P.S. Pao, M.A. Imam, L.A. Cooley: Scripta Metall., 1988, vol. 22, pp. 1241–4410.1016/S0036-9748(88)80139-X ↗
18. K.J. Nix, H.M. Flower: Acta Metall., 1982, vol. 30, pp. 1549–5910.1016/0001-6160(82)90175-4 ↗
19. R.J.H. Wanhill: Metall. Trans. A, 1975, vol. 6A, pp. 1587–9610.1007/BF02641972 ↗
20. J. Lankford, D.L. Davidson: Acta Metall., 1983, vol. 31 (8), pp. 1273–8410.1016/0001-6160(83)90189-X ↗
21. R.M.N. Pelloux: Trans. ASM, 1969, vol. 62, pp. 281–85
22. C.Q. Bowles, D. Broek: Int. J. Fract. Mech., 1972, vol. 8 (1), pp. 75–8510.1007/BF00185199 ↗
23. D.A. Meyn: Trans. ASM, 1968, vol. 61, pp. 52–61
24. P.J.E. Forsyth: Acta Metall., 1963, vol. 11, pp. 703–1510.1016/0001-6160(63)90008-7 ↗
25. J.A. Feeney, J.C. McMillan, R.P. Wei: Met. Trans., 1970, vol. 1, pp. 1741–5710.1007/BF02642025 ↗
26. R.W. Hertzberg and W.J. Mills: in Fractography—Microscopic Cracking Processes, C.D. Beachem and W.R. Warke, eds., ASTM STP 600, ASTM, West Conshohocken, PA, 1976, vol. 11, pp. 220–34
27. J. Beevers: Met. Sci., 1977, vol. 11, pp. 362–6710.1179/msc.1977.11.8-9.362 ↗
28. R.P. Wei and R.P. Gangloff: in Fracture Mechanics: Perspectives and Directions, ASTM STP 1020, R.P. Wei and R.P. Gangloff, eds., ASTM, Philadelphia, PA, 1989, pp. 233–6410.1520/STP1020-EB ↗
29. S.P. Lynch: Corros. Sci., 1982, vol. 22 (10), pp. 925–3710.1016/0010-938X(82)90062-2 ↗
30. G.G. Garrett, J.F. Knott: Acta Metall., 1975, vol. 23, pp. 841–4810.1016/0001-6160(75)90200-X ↗
31. K.R.L. Thompson, J.V. Craig: Metall. Trans., 1970, vol. 1, pp. 1047–4910.1007/BF02811800 ↗
32. Y.J. Ro, S.R. Agnew, R.P. Gangloff: Scripta Metall., 2005, vol. 52, pp. 531–3610.1016/j.scriptamat.2004.10.040 ↗
33. B.M. Gable, A.W. Zhu, A.A. Csontos, E.A. Starke Jr.: J. Light Met., 2001, vol. 1 (1), pp. 1–1410.1016/S1471-5317(00)00002-X ↗
34. H.J. McQueen: JOM, 1998, vol. 50 (6), pp. 28–3310.1007/s11837-998-0124-x ↗
35. J. Hirsch, O. Engler: in Microstructural and Crystallographic Aspects of Recrystallization, N. Hansen, D. Juul Jensen, Y.L. Liu, B. Ralph, eds., Risø National Laboratory, Roskilde, Denmark, 1995, pp. 48–62
36. A.W. Bowen: Mater. Sci. Technol., 1990, vol. 6, pp. 1058–7110.1179/mst.1990.6.11.1058 ↗
37. B. Ren: in Aluminum Alloys for Packaging II, J.G. Morris, S.K. Das, H.S. Goodrich, eds., TMS, Warrendale, PA, 1996, pp. 41–48
38. W. Truszkowski, J. Krǒl, B. Major: Metall. Trans. A, 1980, vol. 11A, pp. 749–5810.1007/BF02661204 ↗
39. T. Kamijo, M. Kikuchi, M. Saga: Mater. Sci. Forum, 1996, vols. 217–222, pp. 577–8210.4028/www.scientific.net/MSF.217-222.577 ↗
40. P.A. Davies, V. Randle: J. Microsc., 2001, vol. 204, pp. 29–3810.1046/j.1365-2818.2001.00922.x ↗
41. J.L. Nelson, J.A. Beavers: Metall. Trans. A, 1979, vol. 10A, pp. 658–6210.1007/BF02658333 ↗
42. G. Themelis, S. Chikwembani, J. Weertman: Mater. Charact., 1990, vol. 24, pp. 27–4010.1016/1044-5803(90)90069-V ↗
43. J.A. Wert, W.M. Robertson: Metallography, 1982, vol. 15, pp. 367–8110.1016/0026-0800(82)90028-3 ↗
44. P.C. Chen, R.C. Wilcox: Mater. Charact., 1991, vol. 26, pp. 9–1510.1016/1044-5803(91)90003-M ↗
45. A.P. Reynolds, G.E. Stoner: Metall. Trans. A, 1991, vol. 22A, pp. 1849–5510.1007/BF02646509 ↗
46. F.S. Lin, E.A. Starke Jr.: Mater. Sci. Eng., 1980, vol. 43, pp. 65–7610.1016/0025-5416(80)90209-8 ↗
47. R.D. Carter, E.W. Lee, E.A. Starke Jr., C.J. Beevers: Metall. Trans. A, 1984, vol. 15A, pp. 555–6310.1007/BF02644980 ↗
48. E.A. Starke, Jr. and J.C. Williams: in Fracture Mechanics: Perspective and Directions (Twenty Symp.), R.P. Wei and R.P. Gangloff, eds., ASTM STP 1020, ASTM, West Conshohocken, PA, 1989, pp. 184–20510.1520/STP18825S ↗
49. E. Hornbogen, K.-H.Z. Gahr: Acta Metall., 1976, vol. 24, pp. 581–9210.1016/0001-6160(76)90104-8 ↗
50. Y. Brechet, F. Louchet, C. Marchionni, J.L. Verger-Gaugry: Philos. Mag. A, 1987, vol. 56 (3), pp. 353–6610.1080/01418618708214391 ↗
51. R. Tintillier, H.J. Gudladt, V. Gerold, J. Petit: in Aluminum-Lithium V, T.H. Sanders, E.A. Starke Jr., eds., Materials and Component Engineering Publications Ltd., Birmingham, United Kingdom, 1989, pp. 1135–46
52. J.R. Rice: Mech. Mater., 1987, vol. 6, pp. 317–3510.1016/0167-6636(87)90030-5 ↗
53. W.C. Crone, T.W. Shield: J. Mech. Phys. Solids, 2001, vol. 49, pp. 2819–3810.1016/S0022-5096(01)00080-1 ↗
54. D.A. Koss, K.S. Chan: Acta Metall., 1980, vol. 28, pp. 1245–5210.1016/0001-6160(80)90080-2 ↗
55. R.A. Oriani: Corros., 1987, vol. 43 (7), pp. 390–9710.5006/1.3583875 ↗
56. R.A. Oriani: in Stress Corrosion Cracking and Hydrogen Embrittlement of Iron-Base Alloys, R.W. Staehle, J. Hochmann, R.D. McCright, J.E. Slater, eds., NACE, Houston, TX, 1977, pp. 351–57
57. S.P. Lynch: in Hydrogen Effects on Material Behavior and Corrosion Deformation Interactions, N.R. Moody, A.W. Thompson, R. Ricker, G. Was, R. Jones, eds., TMS, Warrendale, PA, 2002, pp. 449–66
58. S.P. Lynch: Acta Metall., 1988, vol. 36 (10), pp. 2639–6110.1016/0001-6160(88)90113-7 ↗
59. T. Tabata, H.K. Birnbaum: Scripta Metall., 1983, vol. 17, pp. 947–5010.1016/0036-9748(83)90268-5 ↗
60. G.M. Bond, I.M. Robertson, H.K. Birnbaum: Acta Metall., 1987, vol. 35 (9), pp. 2289–9610.1016/0001-6160(87)90076-9 ↗
61. I.M. Robertson: Eng. Fract. Mech., 1999, vol. 64, pp. 649–7310.1016/S0013-7944(99)00094-6 ↗
62. I.M. Robertson: Eng. Fract. Mech., 2001, vol. 68, pp. 671–9210.1016/S0013-7944(01)00011-X ↗
63. P. Sofronis and I.M. Robertson: Philos. Mag. A, 2002, vol. 82, pp. 3405–1310.1080/01418610208240451 ↗
64. P. Rieux, J. Driver, J. Rieu: Acta Metall., 1979, vol. 27, pp. 145–5310.1016/0001-6160(79)90066-X ↗
65. F.O. Riemelmoser, P. Gumbsch, R. Pippan: Mater. Trans., 2001, vol. 42 (1), pp. 2–1310.2320/matertrans.42.2 ↗
66. F.O. Riemelmoser, R. Pippan, H.P. Stuwe: Acta Mater., 1998, vol. 46 (5), pp. 1793–9910.1016/S1359-6454(97)00366-2 ↗
67. E. Gach and R. Pippan: in Advances in Fracture Research, T. Kishi, Y.-W. Mai, R.O. Ritchie, K. Ravi-Chandar, and A.T. Yokobori, Jr., eds., ICF 10, Elsevier Science, Oxford, United Kingdom, 2001, paper no. ICF100420OR
68. C. Fong, D. Tromans: Metall. Trans. A, 1988, vol. 19A, pp. 2765–7310.1007/BF02645811 ↗
69. R.S. Piascik, R.P. Gangloff: Metall. Trans. A, 1991, vol. 22A, pp. 2415–2810.1007/BF02665008 ↗
70. M. Gao, P.S. Pao, R.P. Wei: Metall. Trans. A, 1988, vol. 19A, pp. 1739–5010.1007/BF02645142 ↗
71. R.P. Gangloff: Comprehensive Structural Integrity, I. Milne, R.O. Ritchie, and B. Karihaloo, eds., Elsevier Science, New York, NY, 2003, vol. 6, pp. 31–101
72. P.J.E. Forsyth, C.A. Stubbington, and D. Clarke: J. Inst. Met., 1961–1962, vol. 90, pp. 238–39
73. L. Christodoulou, H.M. Flower: Acta Metall., 1980, vol. 28, pp. 481–8710.1016/0001-6160(80)90138-8 ↗
74. D.A. Jones, A.F. Jankowski, and G.A. Davidson: Corrosion 97, NACE, Houston, TX, 1997, paper no. 188
75. K.R. Cooper, L.M. Young, R.P. Gangloff, R.G. Kelly: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1625–3410.4028/www.scientific.net/MSF.331-337.1625 ↗
76. J.E. Angelo, N.R. Moody, M.I. Baskes: Modell. Simul. Mater. Sci. Eng., 1995, vol. 3, pp. 289–30710.1088/0965-0393/3/3/001 ↗
77. N.R. Moody, M.I. Baskes, S.L. Robinison, M.W. Perra: Eng. Fract. Mech., 2001, vol. 68, pp. 731–5010.1016/S0013-7944(00)00122-3 ↗
78. J.P. Hirth: Metall. Trans. A, 1980, vol. 11A, pp. 861–9010.1007/BF02654700 ↗
79. J.R. Scully, G.A. Young Jr., S.W. Smith: Mater. Sci. Forum, 2000, vols. 331–337, pp. 1583–9910.4028/www.scientific.net/MSF.331-337.1583 ↗
80. Y.J. Ro, M.R. Begley, R.P. Gangloff, S.R. Agnew: Mater. Sci. Eng. A, 2006, vols. 435–436, pp. 333–42
81. R. Sunder: Fatigue Fract. Eng. Mater. Struct., 2005, vol. 28, pp. 289–30010.1111/j.1460-2695.2005.00857.x ↗
82. J.C. Grosskreutz, G.G. Shaw: Acta Metall., 1972, vol. 20, pp. 523–2810.1016/0001-6160(72)90008-9 ↗