journal article·2012-06

Effects of Aluminum Addition on Tensile and Cup Forming Properties of Three Twinning Induced Plasticity Steels

Seokmin Hong, Sang Yong Shin, Hyoung Seop Kim, Sunghak Lee, Sung-Kyu Kim, Kwang-Geun Chin, Nack J. Kim

Publisher page

Abstract

In the present study, a high Mn twinning induced plasticity (TWIP) steel and two Al-added TWIP steels were fabricated, and their microstructures, tensile properties, and cup formability were analyzed to investigate the effects of Al addition on deformation mechanisms in tensile and cup forming tests. In the high Mn steel, the twin formation was activated to increase the strain hardening rate and ultimate tensile strength, which needed the high punch load during the cup forming test. In the Al-added TWIP steels, the twin formation was reduced, while the slip activation increased, thereby leading to the decrease in strain hardening rate and ultimate tensile strength. As twins and slips were homogeneously formed during the tensile or cup forming test, the punch load required for the cup forming and residual stresses were relatively low, and the tensile ductility was sufficiently high even after the cup forming test. This indicated that making use of twins and slips simultaneously in TWIP steels by the Al addition was an effective way to improve overall properties including cup formability.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. D. Cornette, P. Cugy, A. Hildenbrand, M. Bouzekri, and G. Lovato: SAE Technical Paper presented at the SAE World Congr., SAE International, Detroit, MI, 2005.
2. M.D. Thorpe and H. Adam: SAE Technical Paper presented at the SAE World Congr., SAE International, Detroit, MI, 2002.
3. B.C. De Cooman, L. Chen, H.S. Kim, Y. Estrin, S.K. Kim, and H. Voswinckel: in Microstructure and Texture in Steels, 1st ed., A. Haldar, S. Suwas, and D. Bhattacharjee, eds., Springer Co., New York, NY, 2009, pp. 165–83.10.1007/978-1-84882-454-6_10 ↗
4. H.-H. Bok, M.-G. Lee, H.-D. Kim, and M.-B. Moon: Metall. Mater. Int., 2010, vol. 16, pp. 185–95.10.1007/s12540-010-0405-0 ↗
5. O. Grässel, L. Krger, G. Frommeyer, and L.W. Meyer: Int. J. Plast., 2000, vol. 46, pp. 1391–1409.10.1016/S0749-6419(00)00015-2 ↗
6. S. Allain, J.-P. Chateau, and O. Bouaziz: Mater. Sci. Eng., 2004, vols. A387–A389, pp. 143–47.10.1016/j.msea.2004.01.060 ↗
7. S. Allain: Ph.D. Thesis, Institut National Polytechnique de Lorraine, Nancy, France, 2002.
8. O. Bouaziz and N. Guelton: Mater. Sci. Eng., 2001, vol. A319, pp. 246–49.10.1016/S0921-5093(00)02019-0 ↗
9. S. Vercammen: Ph.D. Thesis, Katholieke Universiteit Leuven, Leuven, Belgium, 2004.
10. Y.N. Dastur and W.C. Leslie: Metall. Trans. A, 1981, vol. 12A, pp. 749–59.10.1007/BF02648339 ↗
11. I. Karaman, H. Sehitoglu, K. Gall, Y.I. Chumlyakov, and H.J. Maier: Acta Mater., 2000, vol. 48, pp. 1345–59.10.1016/S1359-6454(99)00383-3 ↗
12. S. Kibey, J.B. Liu, M.J. Curtis, D.D. Johnson, and H. Sehitoglu: Acta Mater., 2006, vol. 54, pp. 2991–3001.10.1016/j.actamat.2006.02.048 ↗
13. E. Bayraktar, F.A. Khalid, and C. Levaillant: J. Mater. Proc. Technol., 2004, vol. 147, pp. 145–54.10.1016/j.jmatprotec.2003.10.007 ↗
14. B.X. Huang, X.D. Wang, Y.H. Rong, L. Wang, and L. Jin: Mater. Sci. Eng., 2006, vols. A438–A440, pp. 306–40.10.1016/j.msea.2006.02.150 ↗
15. Y. Kim, N. Kang, Y. Park, I. Choi, G. Kim, S. Kim, and K. Cho: J. Kor. Inst. Metall. Mater., 2008, vol. 46, pp. 780–88.
16. J.K. Jung, O.Y. Lee, Y.K. Park, D.E. Kim, K.G. Jin, S.K. Kim, and K.H. Song: J. Kor. Inst. Metall. Mater., 2008, vol. 46, pp. 627–33.
17. O. Bouaziz, S. Allain, and C. Scott: Scripta Mater., 2008, vol. 58, pp. 484–87.10.1016/j.scriptamat.2007.10.050 ↗
18. I. Choi, Y. Park, D. Son, S.-J. Kim, and M. Moon: Metall. Mater. Int., 2010, vol. 16, pp. 27–33.10.1007/s12540-010-0027-6 ↗
19. N. Ma, T. Park, D. Kim, C. Kim, and K. Chung: Metall. Mater. Int., 2010, vol. 16, pp. 427–39.10.1007/s12540-010-0613-7 ↗
20. M.N. Shiekhelsouk, V. Favier, K. Inal, and M. Cherkaoui: Int. J. Plast., 2009, vol. 25, pp. 105–33.10.1016/j.ijplas.2007.11.004 ↗
21. T. Shun, C.M. Wan, and J.G. Byrne: Acta Metall., 1992, vol. 40, pp. 3402–12.10.1016/0956-7151(92)90054-I ↗
22. J.G. Sevillano: Scripta Mater., 2009, vol. 60, pp. 336–39.10.1016/j.scriptamat.2008.10.035 ↗
23. G. Frommeyer, U. Brüx, and P. Neumann: ISIJ Int., 2003, vol. 43, pp. 438–46.10.2355/isijinternational.43.438 ↗
24. K. Sipos, L. Remy, and A. Pineau: Metall. Trans. A, 1976, vol. 7A, pp. 857–64.10.1007/BF02644083 ↗
25. L. Remy and A. Pineau: Mater. Sci. Eng., 1977, vol. A28, pp. 99–107.10.1016/0025-5416(77)90093-3 ↗
26. J.M. Jang, S.J. Kim, N.H. Kang, K.M. Cho, and D.W. Suh: Metall. Mater. Int., 2009, vol. 15, pp. 909–16.10.1007/s12540-009-0909-7 ↗
27. K. Ahn, D. Yoo, M.H. Seo, S.H. Park, and K. Chung: Metall. Mater. Int., 2009, vol. 15, pp. 637–47.10.1007/s12540-009-0637-z ↗
28. S.K. Kim, J. Choi, S.C. Kang, I.R. Shon, and K.G. Chin: POSCO Technical Report, POSCO, Pohang, Korea, 2006, vol. 10, pp. 106–14.
29. B.K. Zuidema, D.K. Subramanyam, and W.C. Leslie: Metall. Trans. A, 1987, vol. 18A, pp. 1629–39.10.1007/BF02646146 ↗
30. L. Chen, H.S. Kim, S.K. Kim, and B.C. De Cooman: ISIJ Int., 2007, vol. 47, pp. 1804–12.10.2355/isijinternational.47.1804 ↗
31. O. Grässel and G. Frommeyer: Mater. Sci. Technol., 1998, vol. 14, pp. 1231–17.10.1179/026708398790300891 ↗
32. K.G. Chin, C.Y. Kang, S.Y. Shin, S. Hong, S. Lee, H.S. Kim, K.-H. Kim, and N.J. Kim: Mater. Sci. Eng., 2011, vol. A528, pp. 2922–28.10.1016/j.msea.2010.12.085 ↗
33. K.T. Park, G. Kim, S.K. Kim, S.W. Lee, S.W. Hwang, and C.S. Lee: Metall. Mater. Int., 2010, vol. 16, pp. 1–6.10.1007/s12540-010-0001-3 ↗
34. M.R. Berrahmoune, S. Berveiller, K. Inal, and E. Patoor: Mater. Sci. Eng., 2006, vol. A438, pp. 262–66.10.1016/j.msea.2006.02.189 ↗
35. M. Nagumo, S. Sekiguchi, H. Hayashi, and K. Takai: Mater. Sci. Eng., 2003, vol. A344, pp. 86–91.10.1016/S0921-5093(02)00403-3 ↗
36. A.P. Miodownik: CALPHAD, 1998, vol. 2, pp. 207–26.10.1016/0364-5916(78)90010-X ↗
37. P.J. Ferreira and P. Mullner: Acta Mater., 1998, vol. 46, pp. 4479–84.10.1016/S1359-6454(98)00155-4 ↗
38. Y.K. Lee and C.S. Choi: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 355–60.10.1007/s11661-000-0271-3 ↗
39. “ASTM E8M-08: Standard Test Methods for Tension Testing of Metallic Materials,” Annual Book of ASTM Standards, ASTM, West Conshohocken, PA, 2008, vol. 03.01, pp. 1–25.
40. C. Scott, N. Guelton, S. Allain, and M. Faral: Proc. MS&T’05 Conf., Pittsburgh, PA, Sept. 2005.
41. H. Schumann: Neue Hütte, 1972, vol. 10, pp. 605–09.
42. K. Ishida, H. Ohtani, N. Satoh, R. Kainuma, and T. Nishizawa: ISIJ Int., 1990, vol. 30, pp. 680–86.10.2355/isijinternational.30.680 ↗
43. J. Kim and B.C. De Cooman: Metall. Mater. Trans. A, 2011, vol. 42A, pp. 932–36.10.1007/s11661-011-0610-6 ↗
44. J.E. Jin and Y.K. Lee: Mater. Sci. Eng., 2009, vol. A527, pp. 157–61.10.1016/j.msea.2009.08.028 ↗
45. K.T. Park, K.G Jin, S.H. Han, S.W. Hwang, K. Choi, and C.S. Lee: Mater. Sci. Eng., 2010, vol. A527, pp. 3651–61.10.1016/j.msea.2010.02.058 ↗
46. T.S. Byun: Acta Mater., 2003, vol. 51, pp. 3063–71.10.1016/S1359-6454(03)00117-4 ↗
47. D. Barbier, N. Gey, S. Allain, N. Bozzolo, and M. Humbert: Mater. Sci. Eng., 2009, vol. A500, pp. 196–206.10.1016/j.msea.2008.09.031 ↗
48. I. Gutierrez-Urrutia, S. Zaefferer, and D. Raabe: Mater. Sci. Eng., 2010, vol. A527, pp. 3552–60.10.1016/j.msea.2010.02.041 ↗
49. K. Yan, D.G. Carr, M.D. Callaghan, K.-D. Liss, and H. Li: Scripta Mater., 2010, vol. 62, pp. 246–49.10.1016/j.scriptamat.2009.11.008 ↗
50. L. Bracke, L. Kestens, and J. Penning: Scripta Mater., 2009, vol. 61, pp. 220–22.10.1016/j.scriptamat.2009.03.045 ↗
51. A.H. Cottrell: in Dislocation and Plastic Flow in Crystals, 1st ed., Claredon Press, Oxford, United Kingdom, 1953, pp. 140–53.
52. J. Kim, L. Chen, H. Kim, S. Kim, Y. Estrin, and B.C. De Cooman: Proc. Int. Conf. on New Developments in Advanced High-Strength Sheet Steels, Orlando, FL, June 2008.
53. O. Bouaziz, S. Allain, C.P. Scott, P. Cugy, and D. Barbier: Curr. Opin. Solid State Mater. Sci., 2011, vol. 15, pp. 141–68.10.1016/j.cossms.2011.04.002 ↗
54. W.G. Johnston: J. Appl. Phys., 1962, vol. 33, pp. 2716–30.10.1063/1.1702538 ↗
55. W.G. Johnston and J.J. Gilman: J. Appl. Phys., 1959, vol. 30, pp. 129–44.10.1063/1.1735121 ↗